Energy Absorption Properties of FRP tube under Commission Load

2003 ◽  
Author(s):  
Atsushi Yokoyama ◽  
Tamotsu Nakatani ◽  
Motoharu Tateishi ◽  
Akihiko Gotoh
Keyword(s):  
Energy Absorption ◽  
Absorption Properties ◽  
Frp Tube

Database System for FRP Tube with Energy Absorption Properties

2003 ◽  
Author(s):  
Akihiko Goto ◽  
Atsushi Yokoyama ◽  
Tamotsu Nakatani
Keyword(s):  
Energy Absorption ◽  
Database System ◽  
Absorption Properties ◽  
Frp Tube

scholarly journals Parametric Analysis on Landing Gear Strut Friction of Light Aircraft for Touchdown Performance

2021 ◽  
Vol 11 (12) ◽  
pp. 5445
Author(s):  
Shengyong Gan ◽  
Xingbo Fang ◽  
Xiaohui Wei
Keyword(s):  
Response Surface ◽  
Energy Absorption ◽  
Landing Gear ◽  
Surface Model ◽  
Absorption Properties ◽  
Surface Method ◽  
Design Variables ◽  
Landing Impact ◽  
Landing Response ◽  
Parametric Studies

The aim of this paper is to obtain the strut friction–touchdown performance relation for designing the parameters involving the strut friction of the landing gear in a light aircraft. The numerical model of the landing gear is validated by drop test of single half-axle landing gear, which is used to obtain the energy absorption properties of strut friction in the landing process. Parametric studies are conducted using the response surface method. Based on the design of the experiment results and response surface functions, the sensitivity analysis of the design variables is implemented. Furthermore, a multi-objective optimization is carried out for good touchdown performance. The results show that the proportion of energy absorption of friction load accounts for more than 35% of the total landing impact energy. The response surface model characterizes well for the landing response, with a minimum fitting accuracy of 99.52%. The most sensitive variables for the four landing responses are the lower bearing width and the wheel moment of inertia. Moreover, the max overloading of sprung mass in LC-1 decreases by 4.84% after design optimization, which illustrates that the method of analysis and optimization on the strut friction of landing gear is efficient for improving the aircraft touchdown performance.

scholarly journals Factors Affecting the Compression and Energy Absorption Properties of Small-Sized Thin-Walled Metal Tubes

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Xiaoqin Hao ◽  
Jia Yu ◽  
Weidong He ◽  
Yi Jiang
Keyword(s):  
Energy Absorption ◽  
Simulation Models ◽  
Simulation Method ◽  
Engineering Practice ◽  
Small Ring ◽  
Metal Tube ◽  
Absorption Properties ◽  
Factors Affecting ◽  
Thin Walled ◽  
Hollow Metal

To solve the problem of the effective cushioning of fast-moving mechanical components in small ring-shaped spaces, the factors affecting the compression and energy absorption properties of small-sized hollow metal tubes were studied. Simulation models were constructed to analyse the influences of tube diameter, wall thickness, relative position, and number of stacked components on the compression and energy absorption properties. The correctness of the simulation method and its output were verified by experiments, which proved the effectiveness of compression and energy absorption properties of small-sized thin-walled metal tubes. The research provides support for the application of metal tube buffers in armament launch technology and engineering practice.

Correlation between Zirconium Addition and Compressive Properties of AZ31 Mg Alloy Foams

2011 ◽  
Vol 121-126 ◽  
pp. 75-79
Author(s):  
Bo Young Hur ◽  
Rui Zhao
Keyword(s):  
Mechanical Properties ◽  
Energy Absorption ◽  
Mg Alloy ◽  
Compressive Properties ◽  
Absorption Properties ◽  
Compression Behavior ◽  
Foaming Agent ◽  
Az31 Mg Alloy ◽  
Absorption Characteristics ◽  
Zirconium Addition

The compressive behaviors of AZ31-Zr foams using Ca particles as thickening agent and CaCO3 powder as foaming agent were investigated in this study. The porosity was about 48.7%~72.9%, pore size was between 0.43~0.97 mm, and homogenous pore structures were obtained. Mechanical properties of AZ31 Mg alloy foams were investigated by means of UTM. The cellular AZ31 Mg foams possess superior comprehensive mechanical properties. The energy absorption characteristics and the effects of compression behavior on the energy absorption properties for the cellular AZ31 Mg foams have been investigated and discussed. The results show that with the addition of Zr, the Mg alloy foam has the highest energy absorption value of 16.26 MJ/m3 and the hardness value of 81.8 HV, which is much higher than that of the foams fabricated without Zr.

Investigation of photon energy absorption properties for some biomolecules

2019 ◽  
Vol 30 (7) ◽  
Author(s):  
Mohammed Sultan Al-Buriahi ◽  
Halil Arslan ◽  
Baris T. Tonguc
Keyword(s):  
Energy Absorption ◽  
Photon Energy ◽  
Absorption Properties

Design of Honeycomb Mesostructures for Crushing Energy Absorption

2012 ◽  
Vol 134 (7) ◽  
Author(s):  
Jesse Schultz ◽  
David Griese ◽  
Jaehyung Ju ◽  
Prabhu Shankar ◽  
Joshua D. Summers ◽  
...  
Keyword(s):  
Sensitivity Analysis ◽  
Energy Absorption ◽  
Wall Thickness ◽  
High Speed ◽  
Fe Simulation ◽  
Honeycomb Structure ◽  
Maximum Energy ◽  
Geometric Parameters ◽  
Constant Mass ◽  
Absorption Properties

This paper presents the energy absorption properties of hexagonal honeycomb structures of varying cellular geometries under high speed in-plane crushing. While the crushing responses in terms of energy absorption and densification strains have been extensively researched and reported, a gap is identified in the generalization of honeycombs with contr’olled and varying geometric parameters. This paper addresses this gap through a series of finite element (FE) simulations where the cell angle and the inclined wall thickness, are varied while maintaining a constant mass of the honeycomb structure. A randomly filled, nonrepeating design of experiments (DOEs) is generated to determine the effects of these geometric parameters on the output of energy absorbed and a statistical sensitivity analysis is used to determine the parameters significant for the crushing energy absorption of honeycombs. It is found that while an increase in the inclined wall thickness enhances the energy absorption of the structure, increases in either the cell angle or ratio of cell angle to inclined wall thickness have adverse effects on the output. Finally, the optimization results suggest that a cellular geometry with a positive cell angle and a high inclined wall thickness provides for maximum energy absorption, which is verified with a 6% error when compared to a FE simulation.

Sign in / Sign up

Export Citation Format

Share Document