Carbon Deposition Reducing Coatings for Highly Loaded Large Diesel Engines

2003 ◽  
Author(s):  
R. Gadow ◽  
D. López ◽  
J. Pérez
Keyword(s):  
Diesel Engines ◽  
Carbon Deposition ◽  
Highly Loaded

scholarly journals Influence of Sulfur and Additives on Wear of Exhaust Valve Seat of Cylinder Head

Complexity ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Jianping Zhao ◽  
Shunli Zhang ◽  
Zhenhuan Dou ◽  
YuBo Sun ◽  
Jiangkun Wan ◽  
...  
Keyword(s):  
Sulfur Content ◽  
Contact Surface ◽  
High Power ◽  
Diesel Engines ◽  
Carbon Deposition ◽  
Diesel Oil ◽  
Exhaust Valve ◽  
Composition Analysis ◽  
Valve Seat ◽  
Protection Mechanism

In this paper, taking a certain type of high-power diesel engine exhaust valve abnormal wear phenomenon as an example, we conduct research on the exhaust valve surface micromorphology characteristics, contact surface accumulation products, additive transition layer, and combustion test. These passed diesel sulfur content comparative test, diesel additive composition analysis, and high-sulfur-content and low-sulfur-content diesel and diesel oil additive action test. At present, there is no authoritative research on the influence of sulfur content in diesel on valve seat wear of high-power diesel engines, and the protection mechanism of diesel additives on the valve seat is not clear. The sulfur in diesel, like the lead in gasoline, has long been known to resist wear in the valve seats of high-power diesel engines; just as gasoline additives compensate for the loss of lead, diesel oil additives seem to compensate for the loss of sulfur. Tests show that a uniform carbon deposition layer is formed on the contact surface after the diesel is burned, and the carbon deposition layer is more densely and uniformly adsorbed on the contact surface under the action of diesel additives to form an antiwear layer. Tests also show that the sulfur in diesel has no effect on the wear resistance of the valve seat.

Microstructural and fractographic characterization of B4C-Al cermets tested under dynamic and static loading

1989 ◽  
Vol 47 ◽  
pp. 562-563
Author(s):  
Gyeung Ho Kim ◽  
Mehmet Sarikaya ◽  
D. L. Milius ◽  
I. A. Aksay
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Static Loading ◽  
Carbon Deposition ◽  
Full Density ◽  
Unique Combination ◽  
Strong Component ◽  
Reaction Products

Cermets are designed to optimize the mechanical properties of ceramics (hard and strong component) and metals (ductile and tough component) into one system. However, the processing of such systems is a problem in obtaining fully dense composite without deleterious reaction products. In the lightweight (2.65 g/cc) B4C-Al cermet, many of the processing problems have been circumvented. It is now possible to process fully dense B4C-Al cermet with tailored microstructures and achieve unique combination of mechanical properties (fracture strength of over 600 MPa and fracture toughness of 12 MPa-m1/2). In this paper, microstructure and fractography of B4C-Al cermets, tested under dynamic and static loading conditions, are described.The cermet is prepared by infiltration of Al at 1150°C into partially sintered B4C compact under vacuum to full density. Fracture surface replicas were prepared by using cellulose acetate and thin-film carbon deposition. Samples were observed with a Philips 3000 at 100 kV.

DEVELOPMENT OF THE COMBUSTION CHAMBER OF GAS ENGINE, CONVERTED ON THE BASIS OF DIESELS D-120 OR D-144 ENGINES TO WORK FOR ON LIQUEFIED PETROLEUM GAS

2019 ◽  
pp. 2-8
Author(s):  
Serhii Kovalov
Keyword(s):  
Combustion Chamber ◽  
Compression Ratio ◽  
Diesel Engines ◽  
Combustion Engine ◽  
Motor Fuel ◽  
Liquefied Petroleum Gas ◽  
Gas Engine ◽  
Chamber Volume ◽  
Motor Fuels ◽  
Dynamic Cycle

The expediency of using vehicles of liquefied petroleum gas as a motor fuel, as com-pared with traditional liquid motor fuels, in particular with diesel fuel, is shown. The advantages of converting diesel engines into gas ICEs with forced ignition with respect to conversion into gas diesel engines are substantiated. The analysis of methods for reducing the compression ratio in diesel engines when converting them into gas ICEs with forced ignition has been carried out. It is shown that for converting diesel engines into gas ICEs with forced ignition, it is advisable to use the Otto thermo-dynamic cycle with a decrease in the geometric degree of compression. The choice is grounded and an open combustion chamber in the form of an inverted axisymmetric “truncated cone” is developed. The proposed shape of the combustion chamber of a gas internal combustion engine for operation in the LPG reduces the geometric compression ratio of D-120 and D-144 diesel engines with an unseparated spherical combustion chamber, which reduces the geometric compression ratio from ε = 16,5 to ε = 9,4. The developed form of the combustion chamber allows the new diesel pistons or diesel pistons which are in operation to be in operation to be refined, instead of making special new gas pistons and to reduce the geometric compression ratio of diesel engines only by increasing the combustion chamber volume in the piston. This method of reducing the geometric degree of compression using conventional lathes is the most technologically advanced and cheap, as well as the least time consuming. Keywords: self-propelled chassis SSh-2540, wheeled tractors, diesel engines D-120 and D-144, gas engine with forced ignition, liquefied petroleum gas (LPG), compression ratio of the internal com-bustion engine, vehicles operating in the LPG.

Sign in / Sign up

Export Citation Format

Share Document