Estimating Real Time Diurnal Permeation from Constant Temperature Measurements

2001 ◽  
Author(s):  
Marek Lockhart ◽  
Mark Nulman ◽  
Giuseppe Rossi
Keyword(s):  
Real Time ◽  
Constant Temperature ◽  
Temperature Measurements

Growth optimization during III-nitride multiwafer MOVPE using real-time curvature, reflectance and true temperature measurements

2007 ◽  
Vol 298 ◽  
pp. 202-206 ◽  
Author(s):  
F. Brunner ◽  
V. Hoffmann ◽  
A. Knauer ◽  
E. Steimetz ◽  
T. Schenk ◽  
...  
Keyword(s):  
Real Time ◽  
Temperature Measurements ◽  
True Temperature ◽  
Growth Optimization

A Novel Solution for Performing Real-Time Fiber Optic Temperature Measurements

2015 ◽  
Author(s):  
Alexander Barry ◽  
David Broaddus ◽  
Jonas Ivasauskas ◽  
William Johnston
Keyword(s):  
Real Time ◽  
Fiber Optic ◽  
Temperature Measurements ◽  
Fiber Optic Temperature

scholarly journals Real-Time Monitoring of Combustion Instability in a Homogeneous Charge Compression Ignition (HCCI) Engine Using Cycle-by-Cycle Exhaust Temperature Measurements

2012 ◽  
Author(s):  
David P. Gardiner ◽  
W. Stuart Neill ◽  
Wallace L. Chippior
Keyword(s):  
Real Time ◽  
Fuel Injection ◽  
Combustion Instability ◽  
Temperature Measurements ◽  
Cylinder Pressure ◽  
Hcci Engine ◽  
Exhaust Temperature ◽  
Indicated Mean Effective Pressure ◽  
Test Engine ◽  
Reference Measurements

This paper describes an experimental study concerning the feasibility of monitoring the combustion instability levels of an HCCI engine based upon cycle-by-cycle exhaust temperature measurements. The test engine was a single cylinder, four-stroke, variable compression ratio Cooperative Fuel Research (CFR) engine coupled to an eddy current dynamometer. A rugged exhaust temperature sensor equipped with special signal processing circuitry was installed near the engine exhaust port. Reference measurements were provided by a laboratory grade, water-cooled cylinder pressure transducer. The cylinder pressure measurements were used to calculate the Coefficient of Variation of Indicated Mean Effective Pressure (COV of IMEP) for each operating condition tested. Experiments with the HCCI engine confirmed that cycle-by-cycle variations in exhaust temperature were present, and were of sufficient magnitude to be captured for processing as high fidelity signal waveforms. There was a good correlation between the variability of the exhaust temperature signal and the COV of IMEP throughout the operating range that was evaluated. The correlation was particularly strong at the low levels of COV of IMEP (2–3%), where production engines would typically operate. A real-time combustion instability signal was obtained from cycle-by-cycle exhaust temperature measurements, and used to provide feedback to the fuel injection control system. Closed loop operation of the HCCI engine was achieved in which the engine was operated as lean as possible while maintaining the COV level at or near 2.5%.

scholarly journals Practical bioinstrumentation developments for AC magnetic field-mediated magnetic nanoparticle heating applications

2018 ◽  
Author(s):  
Mahendran Subramanian ◽  
Arkadiusz Miaskowski ◽  
Ajit K. Mahapatro ◽  
Ondrej Hovorka ◽  
Jon Dobson
Keyword(s):  
Drug Release ◽  
Real Time ◽  
Thermal Imaging ◽  
Heat Dissipation ◽  
Temperature Measurements ◽  
Whole Body ◽  
Planar Coil ◽  
Release Analysis

AbstractHeat dissipation during magnetization reversal processes in magnetic nanoparticles (MNP), upon exposure to alternating magnetic fields (AMF), has been extensively studied in relation to applications in magnetic fluid hyperthermia (MFH). This current paper demonstrates the design, fabrication, and evaluation of an efficient instrument, operating on this principle, for use as (i) a non-contact, in vitro, real-time temperature monitor; (ii) a drug release analysis system (DRAS); (iii) a high flux density module for AMF-mediated MNP studies; and (iv) an in vivo coil setup for real-time, whole body thermal imaging. The proposed DRAS is demonstrated by an AMF-mediated drug release proof-of-principle experiment. Also, the technique described facilitates non-contact temperature measurements of specific absorption rate (SAR) as accurately as temperature measurements using a probe in contact with the sample. Numerical calculations estimating the absolute and root mean squared flux densities, and other MNP – AMF studies suggest that the proposed stacked planar coil module could be employed for calorimetry. Even though the proposed in vivo coil setup could be used for real-time, whole body thermal imaging (within the limitations due to issues of penetration depth), further design effort is required in order to enhance the energy transfer efficiency.

Sign in / Sign up

Export Citation Format

Share Document