Characteristics of Mixture Formation in a Direct Injection SI Engine with Optimized In-Cylinder Swirl Air Motion

1999 ◽  
Author(s):  
Akihiko Kakuhou ◽  
Tomonori Urushihara ◽  
Teruyuki Itoh ◽  
Yasuo Takagi
Keyword(s):  
Direct Injection ◽  
Si Engine ◽  
Mixture Formation ◽  
Air Motion

Effect of n-heptane and n-decane on exhaust odour in direct injection diesel engines

2005 ◽  
Vol 219 (4) ◽  
pp. 565-571 ◽  
Author(s):  
M M Roy
Keyword(s):  
Direct Effect ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Ignition Delay ◽  
Boiling Point ◽  
Alternative Fuels ◽  
Direct Injection ◽  
Cetane Number ◽  
Mixture Formation ◽  
Incomplete Combustion

This study investigated the effect of n-heptane and n-decane on exhaust odour in direct injection (DI) diesel engines. The prospect of these alternative fuels to reduce wall adherence and overleaning, major sources of incomplete combustion, as well as odorous emissions has been investigated. The n-heptane was tested as a low boiling point fuel that can improve evaporation as well as wall adherence. However, the odour is a little worse with n-heptane and blends than that of diesel fuel due to overleaning of the mixture. Also, formaldehyde (HCHO) and total hydrocarbon (THC) in the exhaust increase with increasing n-heptane content. The n-decane was tested as a fuel with a high cetane number that can improve ignition delay, which has a direct effect on wall adherence and overleaning. However, with n-decane and blends, the odour rating is about 0.5-1 point lower than for diesel fuel. Moreover, the aldehydes and THC are significantly reduced. This is due to less wall adherence and proper mixture formation.

Parameter Optimization of a Turbo Charged Direct Injection Flex Fuel SI Engine

2009 ◽  
Vol 2 (1) ◽  
pp. 123-133 ◽  
Author(s):  
Mark J. Christie ◽  
Nicholas Fortino ◽  
Hakan Yilmaz
Keyword(s):  
Parameter Optimization ◽  
Direct Injection ◽  
Si Engine ◽  
Flex Fuel

Effects of the Injection Parameters on the Emissions of a Heavy Duty Diesel Engine

2009 ◽  
Author(s):  
M. Yılmaz ◽  
M. Zafer Gul ◽  
Y. Yukselenturk ◽  
B. Akay ◽  
H. Koten
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Combustion Process ◽  
Design Parameters ◽  
Combustion Model ◽  
Particulate Emissions ◽  
Multiphase Model ◽  
Heavy Duty ◽  
Flow Development ◽  
Air Motion

It is estimated by the experts in the automotive industry that diesel engines on the transport market should increase within the years to come due to their high thermal efficiency coupled with low carbon dioxide (CO2) emissions, provided their nitrogen oxides (NOx) and particulate emissions are reduced. At present, adequate after-treatments, NOx and particulates matter (PM) traps are developed and industrialized with still concerns about fuel economy, robustness, sensitivity to fuel sulfur and cost because of their complex and sophisticated control strategy. New combustion processes focused on clean diesel combustion are investigated for their potential to achieve near zero particulate and NOx emissions. Their main drawbacks are increased level of unburned hydrocarbons (HC) and carbon monoxide (CO) emissions, combustion control at high load and limited operating range and power output. In this work, cold flow simulations for a single cylinder of a nine-liter (6 cylinder × 1.5 lt.) diesel engine have been performed to find out flow development and turbulence generation in the piston-cylinder assembly. In this study, the goal is to understand the flow field and the combustion process in order to be able to suggest some improvements on the in-cylinder design of an engine. Therefore combustion simulations of the engine have been performed to find out flow development and emission generation in the cylinder. Moreover, the interaction of air motion with high-pressure fuel spray injected directly into the cylinder has also been carried out. A Lagrangian multiphase model has been applied to the in-cylinder spray-air motion interaction in a heavy-duty CI engine under direct injection conditions. A comprehensive model for atomization of liquid sprays under high injection pressures has been employed. The combustion is modeled via a new combustion model ECFM-3Z (Extended Coherent Flame Model) developed at IFP. Finally, a calculation on an engine configuration with compression, spray injection and combustion in a direct injection Diesel engine is presented. Further investigation has also been performed in-cylinder design parameters in a DI diesel engine that result in low emissions by effect of high turbulence level. The results are widely in agreement qualitatively with the previous experimental and computational studies in the literature.

scholarly journals Phenomenological model for determining velocity field of LPG jet in combustion chamber of direct injection S.I. engine

2004 ◽  
Vol 26 (2) ◽  
pp. 83-92
Author(s):  
Bui Van Ga ◽  
Phung Xuan Tho ◽  
Nhan Hong Quang ◽  
Nguyen Huu Huong
Keyword(s):  
Combustion Chamber ◽  
Phenomenological Model ◽  
Direct Injection ◽  
Spark Ignition ◽  
Velocity Profiles ◽  
Gas Jet ◽  
Liquefied Petroleum Gas ◽  
Si Engine ◽  
Si Engines ◽  
Stratified Combustion

A phenomenological model has been established to predict the velocity distribution of LPG (Liquefied Petroleum Gas) jet in combustion chamber of spark ignition (SI) engine. A shaped coefficient \(\beta\) governing the similarity of velocity profiles of LPG jets has been defined based on the theoretical and experimental analyses of turbulent diffusion jets. The results show that \(\beta\) is constant for steady jet but it is not the case for unsteady one. The model will enable us to calculate the velocity profiles of LPG jet after ending injection. This is necessary for research of stratified combustion in direct injection LPG SI engines.

scholarly journals Analysis of creation and combustion process of hydrogen-air mixtures by optical method in isochoric chamber

2017 ◽  
Vol 170 (3) ◽  
pp. 121-125
Author(s):  
Marek BRZEŻAŃSKI ◽  
Tadeusz PAPUGA ◽  
Łukasz RODAK
Keyword(s):  
Combustion Chamber ◽  
Flame Front ◽  
Dose Distribution ◽  
Optical Method ◽  
Direct Injection ◽  
Combustion Process ◽  
Variable Composition ◽  
Mixture Formation ◽  
Before And After

The article considers the analysis of combustion process of hydrogen-air mixture of variable composition. Direct injection of hydrogen into the isochoric combustion chamber was applied and the mixture formation took place during the combustion process. The influence of the dose distribution of the fuel supplied before and after ignition on the formation of the flame front and the course of the pressure in the isochoric combustion chamber was discussed. The filming process and registration of pressure in the isochoric chamber during research of combustion process was applied.

Sign in / Sign up

Export Citation Format

Share Document