scholarly journals The Effect of Incorporation of Ferrite Nano-particles on Compressive Strength and Re-sistivity of Self-Compacting Concrete

2015 ◽  
Vol 05 (01) ◽  
pp. 131-138 ◽  
Author(s):  
Mohamed A. Ahmed ◽  
Yehia A. Hassanean ◽  
Kamal A. Assaf ◽  
Moustafa A. Shawkey
Keyword(s):  
Compressive Strength ◽  
Nano Particles ◽  
Self Compacting Concrete

scholarly journals Evaluation of Self-Compacting Concrete Strength with Non-Destructive Tests for Concrete Structures

2019 ◽  
Vol 9 (23) ◽  
pp. 5109 ◽  
Author(s):  
Miguel C. S. Nepomuceno ◽  
Luís F. A. Bernardo
Keyword(s):  
Compressive Strength ◽  
Concrete Strength ◽  
Surface Hardness ◽  
Pulse Velocity ◽  
Concrete Compressive Strength ◽  
Self Compacting Concrete ◽  
Coarse Aggregates ◽  
Pull Out ◽  
Concrete Maturity ◽  
Non Destructive

Self-compacting concrete (SCC) shows to have some specificities when compared to normal vibrated concrete (NVC), namely higher cement paste dosage and smaller volume of coarse aggregates. In addition, the maximum size of coarse aggregates is also reduced in SCC to prevent blocking effect. Such specificities are likely to affect the results of non-destructive tests when compared to those obtained in NVC with similar compressive strength and materials. This study evaluates the applicability of some non-destructive tests to estimate the compressive strength of SCC. Selected tests included the ultrasonic pulse velocity test (PUNDIT), the surface hardness test (Schmidt rebound hammer type N), the pull-out test (Lok-test), and the concrete maturity test (COMA-meter). Seven sets of SCC specimens were produced in the laboratory from a single mixture and subjected to standard curing. The tests were applied at different ages, namely: 1, 2, 3, 7, 14, 28, and 94 days. The concrete compressive strength ranged from 45 MPa (at 24 h) to 97 MPa (at 94 days). Correlations were established between the non-destructive test results and the concrete compressive strength. A test variability analysis was performed and the 95% confidence limits for the obtained correlations were computed. The obtained results for SCC showed good correlations between the concrete compressive strength and the non-destructive tests results, although some differences exist when compared to the correlations obtained for NVC.

An Experimental Investigation on The Influence of Nano Silica on The Strength and Durability Characteristics of Self Compacting Concrete

2021 ◽  
pp. 598-605
Author(s):  
B. Arun Kumar ◽  
Shamshad Begum
Keyword(s):  
Sulphuric Acid ◽  
Chemical Properties ◽  
Particle Packing ◽  
Nano Particles ◽  
Cycle Performance ◽  
Nano Silica ◽  
Self Compacting Concrete ◽  
Chemical Waste ◽  
Concrete Members ◽  
Concrete Production

Self-compacting concrete (SCC) is also considered as a concrete which can be placed and compacted under its own weight with little or no vibration without segregation or bleeding. The use of SCC with its improving productions techniques is increasing everyday in concrete production. It is used to facilitate and ensure proper filling and good structural performance of heavily reinforced structural members. Recently, nano particles have been gaining increasing attention and have been applied in many fields to fabricate new materials with novel functions due to their unique physical and chemical properties. Degradation of concrete members exposed to aggressive sulphuric acid environments is a key durability issue that affects the life cycle performance and maintenance costs of vital civil infrastructure. Sulphuric acid in groundwater, chemical waste or generated from the oxidation of sulphur bearing compounds in backfill can attack substructure concrete members. Moreover, concrete structures in industrial zones are susceptible to deterioration due to acid rain of which sulphuric acid is a chief component. In this work 40Mpa self-compacting concrete is developed using modified Nan-Su method of mix design. Slump flow, J-Ring, V-funnel tests are conducted to justify the fresh properties of SCC and are checked against EFNARC (2005) specifications. Specimens of dimensions 150x150x150mm were cast without nano silica and with two nano silica are added in different percentages(1%, 1.5% and 2% by weight of cement) to SCC. To justify the compressive strength for 7 and 28days, specimens are tested under axial compression. Durability properties were also studied by immersing the specimensin5% HCl and5% H2SO4. The particle packing in concrete can be improved by using Nano-silica which leads to densifying of the micro and nanostructure resulting in improved mechanical properties. Nano-silica addition to cement based materials can also control the degradation of the fundamental C-S-H (calcium-silicate-hydrate) reaction of concrete caused by calcium leaching in water as well as block water penetration and therefore lead to improvements in durability.

Influence of Nano Particles in the Flexural Behavior of High-Strength Reinforced Concrete Beams

2021 ◽  
Vol 1160 ◽  
pp. 25-43
Author(s):  
Naglaa Glal-Eldin Fahmy ◽  
Rasha El-Mashery ◽  
Rabiee Ali Sadeek ◽  
L.M. Abd El-Hafaz
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
High Strength Concrete ◽  
High Strength ◽  
Reinforced Concrete Beams ◽  
Nano Particles ◽  
Flexural Behavior ◽  
Single Type ◽  
Strength Concrete ◽  
Flexural Ductility

High strength concrete (HSC) characterized by high compressive strength but lower ductility compared to normal strength concrete. This low ductility limits the benefit of using HSC in building safe structures. Nanomaterials have gained increased attention because of their improvement of mechanical properties of concrete. In this paper we present an experimental study of the flexural behavior of reinforced beams composed of high-strength concrete and nanomaterials. Eight simply supported rectangular beams were fabricated with identical geometries and reinforcements, and then tested under two third-point loads. The study investigated the concrete compressive strength (50 and 75 N/mm2) as a function of the type of nanomaterial (nanosilica, nanotitanium and nanosilica/nanotitanium hybrid) and the nanomaterial concentration (0%, 0.5% and 1.0%). The experimental results showed that nano particles can be very effective in improving compressive and tensile strength of HSC, nanotitanium is more effective than nanosilica in compressive strength. Also, binary usage of hybrid mixture (nanosilica + nanotitanium) had a remarkable improvement appearing in compressive and tensile strength than using the same percentage of single type of nanomaterials used separately. The reduction in flexural ductility due to the use of higher strength concrete can be compensated by adding nanomaterials. The percentage of concentration, concrete grade and the type of nanomaterials, could predominantly affect the flexural behavior of HSRC beams.

scholarly journals The use of a volcanic material as filler in self-compacting concrete production for lower strength applications

2017 ◽  
Vol 67 (325) ◽  
pp. 111 ◽  
Author(s):  
D. Burgos ◽  
A. Guzmán ◽  
K. M.A. Hossain ◽  
S. Delvasto
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Cementitious Material ◽  
Total Weight ◽  
Self Compacting Concrete ◽  
Lower Strength ◽  
Volcanic Material ◽  
Fine Powders ◽  
Slump Flow ◽  
Concrete Production

This study evaluates the use of large amounts of fine powders (fillers) derived from a Colombian volcanic material into the production of self-compacting concrete (SCC) for lower strength applications. The effects on SCC properties were studied with the incorporation of up to 50% of volcanic material of Tolima (MVT) as a partial substitute of the total weight of Portland cement. The workability was determined through slump flow, V-funnel, and L-box test. The compressive strength results were analyzed statistically by MINITAB. These demonstrated that 30% (by total weight of cementitious material) was the maximum allowable percentage of MVT to be used in the production of SCCs. Based on this, mechanical and permeability properties of SCC MVT 30% were evaluated at 28, 90 y 360 curing days. SCC MVT 30% exhibited compressive strength of 21 and 27 MPa after 28 and 360 days of curing, respectively.

scholarly journals Kajian Karakteristik Beton Memadat Sendiri yang Menggunakan Serat Ijuk (Hal. 54-65)

2018 ◽  
Vol 4 (4) ◽  
pp. 54
Author(s):  
Iis Nurjamilah ◽  
Abinhot Sihotang
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
High Strength ◽  
Self Compacting Concrete ◽  
Palm Fiber ◽  
Fiber Concrete ◽  
Dilute Mixture

ABSTRAKKajian karakteristik beton memadat sendiri yang menggunakan serat ijuk merupakan sebuah kajian yang dilakukan untuk mengetahui pengaruh penambahan serat ijuk terhadap karakteristik beton memadat sendiri (SCC). Beton memadat sendiri yang menggunakan serat ijuk (PFSCC) didesain memiliki campuran yang encer, bermutu tinggi (= 40 MPa) dan memiliki persentase kekuatan lentur yang lebih baik. PFSCC  didapatkan dari hasil pencampuran antara semen sebanyak 85%, fly ash 15%, superplastizicer 1,5%, serat ijuk 0%, 0,5%; 1%; 1,5%; 2% dan 3% dari berat binder (semen + fly ash), kadar air 190 kg/m3, agregat kasar 552,47 kg/m3 dan pasir 1.063 kg/m3. Semakin banyak persentase penambahan serat ijuk ke dalam campuran berdampak terhadap menurunnya workability beton segar. Penambahan serat ijuk yang paling baik adalah sebanyak 1%, penambahan tersebut dapat meningkatkan kekuatan tekan beton sebesar 13% dan lentur sebesar 1,8%.Kata kunci: beton memadat sendiri (SCC), beton berserat, beton memadat sendiri yang menggunakan serat ijuk (PFSCC), serat ijuk ABSTRACTThe study of characteristics self compacting concrete using palm fibers is a study conducted to determine the effect of adding palm fibers to characteristics of self compacting concrete (SCC). palm fibers self compacting concrete (PFSCC) is designed to have a dilute mixture, high strength (= 40 MPa), and have better precentage flexural strength. PFSCC was obtained from mixing of 85% cement, 15% fly ash, 1.5% superplastizicer, 0%, 0.5%, 1%, 1.5%, 2% and 3% palm fibers from the weight of binder  (cement + fly ash), water content 190 kg/m3, coarse aggregate 552.47 kg/m3 and sand 1,063 kg/m3. The more persentage palm fibers content added to the mixture makes workability of fresh concrete decreases. The best addition of palm fiber is 1%, this addition can increases the compressive strength 13% and flexural strength 1.8%.Keywords: self compacting concrete (SCC), fiber concrete, Palm fiber self compacting concrete (PFSCC), palm fiber

scholarly journals Experimental Researchon Flow and Strength Properties of Blended Fibre Reinforced Self Compacting Concrete

2019 ◽  
Vol 8 (6S4) ◽  
pp. 151-155
Keyword(s):  
Compressive Strength ◽  
Aspect Ratio ◽  
Considerable Increase ◽  
Mechanical Vibration ◽  
Strength Properties ◽  
Single Fiber ◽  
Moderate Increase ◽  
Fiber Reinforced ◽  
Self Compacting Concrete ◽  
Split Tensile Strength

Self compacting concrete achieves compaction by itself without using mechanical vibration techniques. Addition of fibers to SCC results in increased performance mainly in flexure, and also in compressive strength. In this study both the flow and strength properties of single Fiber and blended fiber reinforced self compacting concrete are examined in comparison with control self compacting concrete. crimpled steel fibers having size of 0.45mm diameter x 12.5mm length (aspect ratio 27.7) and 0.45mm diameter x 20 mm length (aspect ratio 44.44) are used in the SCC mix at various percentages by weight of cement i.e. 0%, 2%, 4% and 6%. From the obtained results it can be seen that there is aadverse affect on flow properties. There is a moderate increase in the compressive strength, split tensile strength and considerable increase in the flexural strength of the self compacting concrete using the blended fibers at different percentages i.e. at 2% and 4%, when compared to the single fiber reinforced self compacting concrete.

Flexural behaviour of hybrid fibre (steel fiber and silica fume) reinforced self compacting composite concrete members

2014 ◽  
Vol 11 (4) ◽  
pp. 323-330 ◽  
Author(s):  
S. Arivalagan
Keyword(s):  
Compressive Strength ◽  
Silica Fume ◽  
Steel Fiber ◽  
Volume Fraction ◽  
Hardened Concrete ◽  
Flexural Behaviour ◽  
Self Compacting Concrete ◽  
Engineering Structures ◽  
Conventional Concrete ◽  
Concrete Members

The present day world is witnessing the construction of very challenging and difficult civil engineering structures. Self-compacting concrete (SCC) offers several economic and technical benefits; the use of steel fiber extends its possibilities. Steel fiber acts as a bridge to retard their cracks propagation, and improve several characteristics and properties of the concrete. Therefore, an attempt has been made in this investigation to study the Flexural Behaviour of Steel Fiber Reinforced self compacting concrete incorporating silica fume in the structural elements. The self compacting concrete mixtures have a coarse aggregate replacement of 25% and 35% by weight of silica fume. Totally eight mixers are investigated in which cement content, water content, dosage of superplasticers were all constant. Slump flow time and diameter, J-Ring, V-funnel, and L-Box were performed to assess the fresh properties of the concrete. The variable in this study was percentage of volume fraction (1.0, 1.5) of steel fiber. Finally, five beams were to be casted for study, out of which one was made with conventional concrete, one with SCC (25% silica fume) and other were with SCC (25% silica fume + 1% of steel fiber, 25% silica fume + 1.5% of steel fiber) one with SCC (35% silica fume), and other were SCC (35% Silica fume + 1% of steel fiber, 35% Silica fume + 1.5% of steel fiber). Compressive strength, flexural strength of the concrete was determined for hardened concrete for 7 and 28 days. This investigation is also done to determine the increase the compressive strength by addition of silica fume by varying the percentage.

Sign in / Sign up

Export Citation Format

Share Document