Indirect Determination of Material Properties of Closed-Cell Metal Foam: Comparison of Voxel and Tetrahedral Finite Element Models

2012 ◽  
Author(s):  
O. Jiroušek ◽  
P. Koudelka ◽  
P. Zlámal
Keyword(s):  
Finite Element ◽  
Material Properties ◽  
Metal Foam ◽  
Finite Element Models ◽  
Indirect Determination ◽  
Closed Cell

Determination of Charge Coefficient of Piezoelectric Films Using a Combined Finite Element Model and Dynamic Loading Technique

2020 ◽  
Vol 835 ◽  
pp. 229-242
Author(s):  
Oboso P. Bernard ◽  
Nagih M. Shaalan ◽  
Mohab Hossam ◽  
Mohsen A. Hassan
Keyword(s):  
Finite Element ◽  
Dynamic Loading ◽  
Material Properties ◽  
Accurate Determination ◽  
Substrate Material ◽  
Experimental Results ◽  
Piezoelectric Composite ◽  
Piezoelectric Film ◽  
Piezoelectric Charge

Accurate determination of piezoelectric properties such as piezoelectric charge coefficients (d33) is an essential step in the design process of sensors and actuators using piezoelectric effect. In this study, a cost-effective and accurate method based on dynamic loading technique was proposed to determine the piezoelectric charge coefficient d33. Finite element analysis (FEA) model was developed in order to estimate d33 and validate the obtained values with experimental results. The experiment was conducted on a piezoelectric disc with a known d33 value. The effect of measuring boundary conditions, substrate material properties and specimen geometry on measured d33 value were conducted. The experimental results reveal that the determined d33 coefficient by this technique is accurate as it falls within the manufactures tolerance specifications of PZT-5A piezoelectric film d33. Further, obtained simulation results on fibre reinforced and particle reinforced piezoelectric composite were found to be similar to those that have been obtained using more advanced techniques. FE-results showed that the measured d33 coefficients depend on measuring boundary condition, piezoelectric film thickness, and substrate material properties. This method was proved to be suitable for determination of d33 coefficient effectively for piezoelectric samples of any arbitrary geometry without compromising on the accuracy of measured d33.

Constitutive Laws for Biomechanical Modeling of Refractive Surgery

1996 ◽  
Vol 118 (4) ◽  
pp. 473-481 ◽  
Author(s):  
Michael R. Bryant ◽  
Peter J. McDonnell
Keyword(s):  
Finite Element ◽  
Material Properties ◽  
Refractive Surgery ◽  
Fiber Optic ◽  
Transverse Isotropy ◽  
Constitutive Laws ◽  
Finite Element Models ◽  
Corneal Refractive Surgery ◽  
Best Fit ◽  
Membrane Inflation

Membrane inflation tests were performed on fresh, intact human corneas using a fiber optic displacement probe to measure the apical displacements. Finite element models of each test were used to identify the material properties for four different constitutive laws commonly used to model corneal refractive surgery. Finite element models of radial keratotomy using the different best-fit constitutive laws were then compared. The results suggest that the nonlinearity in the response of the cornea is material rather than geometric, and that material nonlinearity is important for modeling refractive surgery. It was also found that linear transverse isotropy is incapable of representing the anisotropy that has been experimentally measured by others, and that a hyperelastic law is not suitable for modeling the stiffening response of the cornea.

The Role of Topology and Tissue Mechanics in Remora Attachment

2014 ◽  
Vol 1648 ◽  
Author(s):  
Michael Culler ◽  
Keri A. Ledford ◽  
Jason H. Nadler
Keyword(s):  
Finite Element ◽  
Material Properties ◽  
Tissue Mechanics ◽  
Unit Cell ◽  
Surface Topology ◽  
Finite Element Models ◽  
Cell Geometry ◽  
Critical Step ◽  
Tissue Material

ABSTRACTRemora fish are capable of fast, reversible and reliable adhesion to a wide variety of both natural and artificial marine hosts through a uniquely evolved dorsal pad. This adhesion is partially attributed to suction, which requires a robust seal between the pad interior and the ambient environment. Understanding the behavior of remora adhesion based on measurable surface parameters and material properties is a critical step when creating artificial, bio-inspired devices. In this work, structural and fluid finite element models (FEM) based on a simplified “unit cell” geometry were developed to predict the behavior of the seal with respect to host/remora surface topology and tissue material properties.

Modeling the HSK Toolholder-Spindle Interface

2002 ◽  
Vol 124 (3) ◽  
pp. 734-744 ◽  
Author(s):  
Ihab M. Hanna ◽  
John S. Agapiou ◽  
David A. Stephenson
Keyword(s):  
Finite Element ◽  
Material Properties ◽  
System Reliability ◽  
High Volume ◽  
Finite Element Models ◽  
Operational Experience ◽  
Bending Load ◽  
Load Carrying ◽  
Detailed Evaluation ◽  
Contact Pressures

The HSK toolholder-spindle connection was developed to overcome shortcomings of the 7/24 steep-taper interface, especially at higher speeds. However, the HSK system was standardized quickly, without detailed evaluation based on operational experience. Several issues concerning the reliability, maintainability, and safety of the interface have been raised within the international engineering community. This study was undertaken to analytically investigate factors which influence the performance and limitations of the HSK toolholder system. Finite Element Models were created to analyze the effects of varying toolholder and spindle taper geometry, axial spindle taper length, drawbar/clamping load, spindle speed, applied bending load, and applied torsional load on HSK toolholders. Outputs considered include taper-to-taper contact pressures, taper-to-taper clearances, minimum drawbar forces, interface stiffnesses, and stresses in the toolholder. Static deflections at the end of the holder predicted by the models agreed well with measured values. The results showed that the interface stiffness and load-carrying capability are significantly affected by taper mismatch and dimensional variations, and that stresses in the toolholder near the drive slots can be quite high, leading to potential fatigue issues for smaller toolholders subjected to frequent clamping-unclamping cycles (e.g., in high volume applications). The results can be used to specify minimum toolholder material properties for critical applications, as well as drawbar design and spindle/toolholder gaging guidelines to increase system reliability and maintainability.

scholarly journals High-Fidelity Sensitivity Analysis of Modal Properties of Mistuned Bladed Disks Regarding Material Anisotropy

2018 ◽  
Author(s):  
Adam Koscso ◽  
Guido Dhondt ◽  
E. P. Petrov
Keyword(s):  
Sensitivity Analysis ◽  
Finite Element ◽  
Natural Frequencies ◽  
Mode Shapes ◽  
Finite Element Models ◽  
Coordinate Systems ◽  
Bladed Disks ◽  
Bladed Disk ◽  
Material Orientation

A new method has been developed for sensitivity calculations of modal characteristics of bladed disks made of anisotropic materials. The method allows the determination of the sensitivity of the natural frequencies and mode shapes of mistuned bladed disks with respect to anisotropy angles that define the crystal orientation of the monocrystalline blades using full-scale finite element models. An enhanced method is proposed to provide high accuracy for the sensitivity analysis of mode shapes. An approach has also been developed for transforming the modal sensitivities to coordinate systems used in industry for description of the blade anisotropy orientations. The capabilities of the developed methods are demonstrated on examples of a single blade and a mistuned realistic bladed disk finite element models. The modal sensitivity of mistuned bladed disks to anisotropic material orientation is thoroughly studied.

Modeling the HSK (Hollow Shank Taper 1/10 Tapered Joint) Toolholder-Spindle Interface

2000 ◽  
Author(s):  
Ihab M. Hanna ◽  
John S. Agapiou ◽  
David A. Stephenson
Keyword(s):  
Finite Element ◽  
Material Properties ◽  
System Reliability ◽  
High Volume ◽  
Finite Element Models ◽  
Operational Experience ◽  
Bending Load ◽  
Load Carrying ◽  
Detailed Evaluation ◽  
Contact Pressures

Abstract The HSK toolholder-spindle connection was developed to overcome shortcomings of the 7/24 steep-taper interface, especially at higher speeds. However, the HSK system was standardized quickly, without detailed evaluation based on operational experience. Several issues concerning the reliability, maintainability, and safety of the interface have been raised within the international engineering community. This study was undertaken to analytically investigate factors which influence the performance and limitations of the HSK toolholder system. Finite Element Models were created to analyze the effects of varying toolholder and spindle taper geometry, axial spindle taper length, drawbar/clamping load, spindle speed, applied bending load, and applied torsional load on HSK toolholders. Outputs considered include taper-to-taper contact pressures, taper-to-taper clearances, minimum drawbar forces, interface stiffnesses, and stresses in the toolholder. Static deflections at the end of the holder predicted by the models agreed well with measured values. The results showed that the interface stiffness and load-carrying capability are significantly affected by taper mismatch and dimensional variations, and that stresses in the toolholder near the drive slots can be quite high, leading to potential fatigue issues for smaller toolholders subjected to frequent clamping-unclamping cycles (e.g., in high volume applications). The results can be used to specify minimum toolholder material properties for critical applications, as well as drawbar design and spindle/toolholder gaging guidelines to increase system reliability and maintainability.

Numerical Investigation on Weld-Induced Imperfections in Aluminum Ship Plates

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Bai-Qiao Chen ◽  
C. Guedes Soares
Keyword(s):  
Finite Element ◽  
Aluminum Alloy ◽  
Material Properties ◽  
Welding Process ◽  
Finite Element Models ◽  
Finite Element Analyses ◽  
Temperature Dependent ◽  
Military Applications ◽  
Structural Responses ◽  
Or In Military

The present work aims at better understanding and predicting the thermal and structural responses of aluminum components subjected to welding, contributing to the design and fabrication of aluminum ships such as catamarans, lifesaving boats, tourist ships, and fast ships used in transportation or in military applications. Taken into consideration the moving heat source in metal inert gas (MIG) welding, finite element models of plates made of aluminum alloy are established and validated against published experimental results. Considering the temperature-dependent thermal and mechanical properties of the aluminum alloy, thermo-elasto-plastic finite element analyses are performed to determine the size of the heat-affected zone (HAZ), the temperature histories, the distortions, and the distributions of residual stresses induced by the welding process. The effects of the material properties on the finite element analyses are discussed, and a simplified model is proposed to represent the material properties based on their values at room temperature.

Modal Velocity-Based Multiaxial Fatigue Damage Evaluation Using Simplified Finite Element Models

2020 ◽  
Vol 87 (11) ◽  
Author(s):  
Kurthan Kersch ◽  
Elmar Woschke
Keyword(s):  
Finite Element ◽  
Fatigue Damage ◽  
Cross Section ◽  
Multiaxial Fatigue ◽  
Finite Element Models ◽  
Damage Evaluation ◽  
Geometric Factors ◽  
The Relationship ◽  
General Method

Abstract This work proposes a new method for the fatigue damage evaluation of vibrational loads, based on preceding investigations on the relationship between stresses and modal velocities. As a first step, the influence of the geometry on the particular relationship is studied. Therefore, an analytic expression for Euler Bernoulli beams with a non-constant cross section is derived. Afterward, a general method for obtaining geometric factors from finite element (FE) models is proposed. In order to ensure a fast fatigue damage evaluation, strongly simplified FE-models are used for the determination of both factors and measurement locations. The entire method is demonstrated on three mechanical structures and indicates a better compromise between effort and accuracy than existing methods. For all examples, the usage of velocities and geometric factors obtained from simplified FE models enables a sufficient fatigue damage calculation.

Fracture Prediction for the Proximal Femur Using Finite Element Models: Part I—Linear Analysis

1991 ◽  
Vol 113 (4) ◽  
pp. 353-360 ◽  
Author(s):  
J. C. Lotz ◽  
E. J. Cheal ◽  
W. C. Hayes
Keyword(s):  
Finite Element ◽  
Fracture Risk ◽  
Strain Gage ◽  
Proximal Femur ◽  
Material Properties ◽  
The United States ◽  
Nonlinear Material ◽  
Finite Element Models ◽  
Model Predictions

Over 90 percent of the more than 250,000 hip fractures that occur annually in the United States are the result of falls from standing height. Despite this, the stresses associated with femoral fracture from a fall have not been investigated previously. Our objectives were to use three-dimensional finite element models of the proximal femur (with geometries and material properties based directly on quantitative computed tomography) to compare predicted stress distributions for one-legged stance and for a fall to the lateral greater trochanter. We also wished to test the correspondence between model predictions and in vitro strain gage data and failure loads for cadaveric femora subjected to these loading conditions. An additional goal was to use the model predictions to compare the sensitivity of several imaging sites in the proximal femur which are used for the in vivo prediction of hip fracture risk. In this first of two parts, linear finite element models of two unpaired human cadaveric femora were generated. In Part II, the models were extended to include nonlinear material properties for the cortical and trabecular bone. While there was poor correspondence between strain gage data and model predictions, there was excellent agreement between the in vitro failure data and the linear model, especially using a von Mises effective strain failure criterion. Both the onset of structural yielding (within 22 and 4 percent) and the load at fracture (within 8 and 5 percent) were predicted accurately for the two femora tested. For the simulation of one-legged stance, the peak stresses occurred in the primary compressive trabeculae of the subcapital region. However, for a simulated fall, the peak stresses were in the intertrochanteric region. The Ward’s triangle (basicervical) site commonly used for the clinical assessment of osteoporosis was not heavily loaded in either situation. These findings suggest that the intertrochanteric region may be the most sensitive site for the assessment of fracture risk due to a fall and the subcapital region for fracture risk due to repetitive activities such as walking.

Sign in / Sign up

Export Citation Format

Share Document