scholarly journals Floatation-Spectrophotometric Determination of Thorium, Using Complex Formation with Eriochrome Cyanine R

2011 ◽  
Vol 6 ◽  
pp. ACI.S5949 ◽  
Author(s):  
Sabah Shiri ◽  
Ali Delpisheh ◽  
Ali Haeri ◽  
Abdolhossein Poornajaf ◽  
Tahereh Khezeli ◽  
...  
Keyword(s):  
Complex Formation ◽  
Aqueous Phase ◽  
Signal To Noise Ratio ◽  
Calibration Graph ◽  
Signal To Noise ◽  
Brij 35 ◽  
Relative Standard ◽  
Optimized Conditions ◽  
Interfering Ions

A novel and sensitive floatation-spectrophotometric method is presented for determination of trace amounts of thorium in water samples. The method is based on the ion-associated formation between thorium, Eriochrome cyanine R and Brij-35 at pH = 4 media. The complex was floated in the interface of the aqueous phase and n-hexane by vigorous shaking. After removing the aqueous phase the floated particles were dissolved in methanol and the absorbance was measured at 607 nm. The influence of different important parameters such as Eriochrome cyanine R and surfactants concentration, pH, volume of n-hexane, standing time and interfering ions were evaluated. Under optimized conditions the calibration graph was linear in the range of 6-230 ng mL-1 of thorium with a correlation coefficient of 0.9985. The limit of detections (LOD), based on signal to noise ratio (S/N) of 3 was 1.7 ng mL-1. The relative standard deviations for determination of 150 and 30 ng ml-1 of thorium were 3.26 and 4.41%, respectively (n = 10). The method showed a good linearity, recoveries, as well as some advantages such as sensitivity, simplicity, affordability and a high feasibility. The method was successfully applied to determine thorium in different water and urine samples.

scholarly journals Determination of Flumequine in Channel Catfish by Liquid Chromatography with Fluorescence Detection

1999 ◽  
Vol 82 (3) ◽  
pp. 614-619 ◽  
Author(s):  
Steven M Plakas ◽  
Kathleen R El Said ◽  
F Aladar Bencsath ◽  
Steven M Musser ◽  
Calvin C Walker
Keyword(s):  
Liquid Chromatography ◽  
Fluorescence Detection ◽  
Ictalurus Punctatus ◽  
Channel Catfish ◽  
Solid Phase ◽  
Signal To Noise Ratio ◽  
Methanol Solution ◽  
Signal To Noise ◽  
Relative Standard

Abstract Rapid methods are described for determination of flumequine (FLU) residues in muscle and plasma of farm-raised channel catfish (Ictalurus punctatus). FLU residues were extracted from tissues with an acidified methanol solution, and extracts were cleaned up on C18 solid-phase extraction cartridges. FLU concentrations were determined by liquid chromatography (LC)using a C18 analytical column and fluorescence detection (excitation, 325 nm; emission, 360 nm). Mean recoveries of FLU from fortified muscle were 87–94% at 5 levels ranging from 10 to 160 ppb (5 replicates per level). FLU recoveries from fortified plasma were 92–97% at 5 levels ranging from 20 to 320 ppb. Limits of detection (signal-to-noise ratio, 3:1)for the method as described were 3 and 6 ppb for muscle and plasma, respectively. Relative standard deviations (RSDs) for recoveries were ≤12%. Live catfish were dosed with 14C-labeled or unlabeled FLU to generate incurred residues. Recoveries of 14C residues throughout extraction and cleanup were 90 and 94% for muscle and plasma, respectively. RSDs for incurred FLU at 2 levels in muscle and plasma ranged from 2 to 6%. The identity of FLU in incurred tissues was confirmed by LC/mass spectrometry.

Cloud Point Extraction and Spectrophotometry Determination of Lead in Environment Water Using 5-Br-PADAP

2013 ◽  
Vol 830 ◽  
pp. 345-348
Author(s):  
Lin Gao ◽  
Sheng Jie Chen ◽  
Fang Chen ◽  
Wen Hong Zhou ◽  
Jun Long Yao
Keyword(s):  
Cloud Point ◽  
Cloud Point Extraction ◽  
Detection Method ◽  
Low Cost ◽  
Calibration Graph ◽  
Buffer Solution ◽  
Relative Standard ◽  
Triton X ◽  
Optimized Conditions

A simple, sensitive, green and low cost detection method based on the cloud point extraction (CPE) separation and spectrophotometry was proposed for the determination of lead. In pH=9.0 H3BO3 buffer solution, Pb(II) reacts with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) in the presence of Triton X-100 yielding a hydrophobic complex, which then is extracted into micro-volume surfactant-rich phase. The calibration graph was linear in the range of 20-400 µg/L (at 560 nm). Under the optimized conditions, the detection limits of 10.94 µg/L and the relative standard deviations(RSD) of 2.0% (n=5) for Lead(II) were found, respectively. The sensitivity and absorbance of this method are at least five times higher when compared with that of usual 5-Br-PADAP spectrophotometry without CPE, and the proposed method has been applied to the determination of Lead in environment water samples with satisfactory results.

scholarly journals Capillary Electrophoretic-Ultraviolet Method for the Separation and Estimation of Zineb, Maneb, and Ferbam in Food Samples

2007 ◽  
Vol 90 (3) ◽  
pp. 834-837 ◽  
Author(s):  
Jatinder Singh Aulakh ◽  
Agnes Fekete ◽  
Ashok Kumar Malik ◽  
Rakesh Kumar Mahajan ◽  
Philippe Schmitt-Kopplin
Keyword(s):  
Signal To Noise Ratio ◽  
Food Samples ◽  
Tetraacetic Acid ◽  
Signal To Noise ◽  
Electrophoretic Method ◽  
Ultraviolet Detection ◽  
Buffer Solutions ◽  
Relative Standard ◽  
Capillary Electrophoretic

Abstract A simple and sensitive capillary electrophoretic method with ultraviolet detection has been developed for the separation and determination of ferbam [iron(III)-dimethyldithiocarbamate], maneb [manganese(II)-ethylenebisdithiocarbamate] and zineb [zinc(II)-ethylenebisdithiocarbamate], in borate buffer, after their acidic decomposition and complexation with CDTA (trans-1,2-diaminocyclohexane-N,N,N,N-tetraacetic acid monohydrate), as CDTA-metal complexes of Fe+3, Mn+2, and Zn+2. The determination is dependent on the pH and the nature of the buffer solutions. In this method, the detection limit (signal-to-noise ratio = 3) is 0.0013, 0.0022, and 0.0023 mM for ferbam, maneb, and zineb, respectively. The relative standard deviation for the analysis of 1 mM of each was found to be 1.5 0.2%. The method was successfully applied for the analysis of red beans and grain samples spiked with ferbam, maneb, and zineb. The applicability of capillary electrophoresis as a useful tool for the simultaneous determination and analysis of ferbam, maneb, and zineb is demonstrated.

Determination of the Best Emulsion for the Microscopy of Crystals

1981 ◽  
Vol 39 ◽  
pp. 32-33
Author(s):  
David A. Grano ◽  
Kenneth H. Downing
Keyword(s):  
Spatial Frequency ◽  
Information Transfer ◽  
Signal To Noise Ratio ◽  
Experimental Situation ◽  
Photographic Emulsion ◽  
Modulation Transfer ◽  
Signal To Noise ◽  
Frequency Space ◽  
Noise Ratio

The retrieval of high-resolution information from images of biological crystals depends, in part, on the use of the correct photographic emulsion. We have been investigating the information transfer properties of twelve emulsions with a view toward 1) characterizing the emulsions by a few, measurable quantities, and 2) identifying the “best” emulsion of those we have studied for use in any given experimental situation. Because our interests lie in the examination of crystalline specimens, we've chosen to evaluate an emulsion's signal-to-noise ratio (SNR) as a function of spatial frequency and use this as our critereon for determining the best emulsion.The signal-to-noise ratio in frequency space depends on several factors. First, the signal depends on the speed of the emulsion and its modulation transfer function (MTF). By procedures outlined in, MTF's have been found for all the emulsions tested and can be fit by an analytic expression 1/(1+(S/S0)2). Figure 1 shows the experimental data and fitted curve for an emulsion with a better than average MTF. A single parameter, the spatial frequency at which the transfer falls to 50% (S0), characterizes this curve.

Selective electromembrane extraction and sensitive colorimetric detection of copper(II)

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Wajid Ali Khan ◽  
Muhammad Balal Arain ◽  
Hashmat Bibi ◽  
Mustafa Tuzen ◽  
Nasrullah Shah ◽  
...  
Keyword(s):  
Applied Voltage ◽  
Colorimetric Detection ◽  
Environmental Water ◽  
Selective Extraction ◽  
Effective Parameters ◽  
Relative Standard ◽  
Electromembrane Extraction ◽  
Optimized Conditions ◽  
Donor Phase

AbstractIn this study, an extremely effective electromembrane extraction (EME) method was developed for the selective extraction of Cu(II) followed by Red-Green-Blue (RGB) detection. The effective parameters optimized for the extraction efficiency of EME include applied voltage, extraction time, supported liquid membrane (SLM) composition, pH of acceptor/donor phases, and stirring rate. Under optimized conditions, Cu(II) was extracted from a 3 mL aqueous donor phase to 8 µL of 100 mM HCl acceptor solution through 1-octanol SLM using an applied voltage of 50 V for 15 min. The proposed method provides a working range of 0.1–0.75 µg·mL−1 with 0.03 µg·mL−1 limit for detection. Finally, the developed technique was applied to different environmental water samples for monitoring environmental pollution. Obtained relative recoveries were within the range of 93–106%. The relative standard deviation (RSD) and enhancement factor (EF) were found to be ≤4.8% and 100 respectively. We hope that this method can be introduced for quantitative determination of Cu(II) as a fast, simple, portable, inexpensive, effective, and precise procedure.

Development of a solid-phase extraction – spectrofluorimetric method for trace glutathione determination

2011 ◽  
Vol 89 (4) ◽  
pp. 517-523 ◽  
Author(s):  
Ke-Jing Huang ◽  
Cong-Hui Han ◽  
Ying-Ying Wu ◽  
Chao-Qun Han ◽  
De-Jun Niu ◽  
...  
Keyword(s):  
Solid Phase Extraction ◽  
Limit Of Detection ◽  
Solid Phase ◽  
Signal To Noise Ratio ◽  
Calibration Graph ◽  
Extraction Column ◽  
Phase Extraction ◽  
Selective Reaction ◽  
Spectrofluorimetric Method ◽  
Relative Standard

A simple and efficient solid-phase extraction – spectrofluorimetric method has been developed to determine glutathione (GSH). Fluorescent probe N-(4,4-difluoro-5,7-dimethyl-4-bora-3a,4a-diaza-s-indacene-3-yl)methyl)iodoacetamide (BODIPY Fl-C1-IA) was used as the derivatization reagent. The procedure was based on a BODIPY Fl-C1-IA selective reaction with GSH to form the highly fluorescent product BODIPY Fl-C1-IA–GSH, using a solid-phase extraction column and spectrofluorimetric determination. The variables affecting analytical performance were studied and optimized. The calibration graph using the preconcentration system for GSH was linear over the range of 1–200 nmol/L with a limit of detection of 0.05 nmol/L (signal-to-noise ratio = 3). The relative standard deviation for six replicate determinations of GSH at the 100 nmol/L concentration level was 3.9%. The method was applied to water samples and average recoveries between 87.5% and 111.5% were obtained for spiked samples.

Determination of Tin in Canned Fruits and Vegetables by Atomic Absorption Spectrometry and Liquid–Liquid Extraction

1994 ◽  
Vol 77 (6) ◽  
pp. 1627-1630 ◽  
Author(s):  
Ana M Martín ◽  
Mercedes Sánchez ◽  
Pedro Espinosa ◽  
Gracia Bagur
Keyword(s):  
Aqueous Phase ◽  
Fruits And Vegetables ◽  
Methyl Ketone ◽  
Absorption Spectrometry ◽  
Liquid Extraction ◽  
Acid Complex ◽  
Liquid Liquid Extraction ◽  
Relative Standard ◽  
Good Agreement

Abstract A method was developed for the determination of tin based on the extraction of its 5,5-methylenedisalicylohydroxamic acid complex with 1.09M isobutyl methyl ketone in tributyl phosphate. After the samples were treated with nitric and hydrochloric acid, the aqueous phase was made to 0.05M in perchloric acid. When the ratio of aqueous phase to organic phase was 4:1 (v/v), the detection limit and the relative standard deviation (n = 7,50 μg tin) were 0.20 μg/mL and 0.9%, respectively. The proposed method was applied to the analysis of tin in canned fruits and vegetables. The results were in good agreement with those obtained by the phenylfluorone method.

scholarly journals Distance scaling method for accurate prediction of slowly varying magnetic fields in satellite missions

2016 ◽  
Vol 5 (2) ◽  
pp. 281-288 ◽  
Author(s):  
Panagiotis P. Zacharias ◽  
Elpida G. Chatzineofytou ◽  
Sotirios T. Spantideas ◽  
Christos N. Capsalis
Keyword(s):  
Signal To Noise Ratio ◽  
Near Field ◽  
Magnetic Behavior ◽  
Field Measurements ◽  
High Signal ◽  
Signal To Noise ◽  
Scaling Method ◽  
Magnetic Signature ◽  
The Magnetic Field

Abstract. In the present work, the determination of the magnetic behavior of localized magnetic sources from near-field measurements is examined. The distance power law of the magnetic field fall-off is used in various cases to accurately predict the magnetic signature of an equipment under test (EUT) consisting of multiple alternating current (AC) magnetic sources. Therefore, parameters concerning the location of the observation points (magnetometers) are studied towards this scope. The results clearly show that these parameters are independent of the EUT's size and layout. Additionally, the techniques developed in the present study enable the placing of the magnetometers close to the EUT, thus achieving high signal-to-noise ratio (SNR). Finally, the proposed method is verified by real measurements, using a mobile phone as an EUT.

scholarly journals New Spectrofluorimetric Method with Enhanced Sensitivity for Determination of Paroxetine in Dosage Forms and Plasma

2008 ◽  
Vol 3 ◽  
pp. ACI.S1053 ◽  
Author(s):  
Ibrahim A. Darwish ◽  
Sawsan M. Amer ◽  
Heba H. Abdine ◽  
Lama I. Al-Rayes
Keyword(s):  
High Sensitivity ◽  
Dosage Forms ◽  
Official Method ◽  
Factors Affecting ◽  
Pharmaceutical Tablets ◽  
Enhanced Sensitivity ◽  
Spectrofluorimetric Method ◽  
Relative Standard ◽  
Optimized Conditions

New simple spectrofluorimetric method with enhanced sensitivity has been developed and validated for the determination of the antidepressant paroxetine (PXT) in its dosage forms and plasma. The method was based on nucleophilic substitution reaction of PXT with 4-chloro-7-nitrobenzo-2-oxa-1,3-diazole in an alkaline medium (pH 8) to form a highly fluorescent derivative that was measured at 545 nm after excitation at 490 nm. The factors affecting the reaction was carefully studied and optimized. The kinetics of the reaction was investigated, and the reaction mechanism was presented. Under the optimized conditions, linear relationship with good correlation coefficient (0.9993) was found between the fluorescence intensity and PXT concentration in the range of 80-800 ng ml-1. The limits of detection and quantitation for the method were 25 and 77 ng ml-1, respectively. The precision of the method was satisfactory; the values of relative standard deviations did not exceed 3%. The proposed method was successfully applied to the determination of PXT in its pharmaceutical tablets with good accuracy; the recovery values were 100.2 ± 1.61%. The results obtained by the proposed method were comparable with those obtained by the official method. The proposed method is superior to the previously reported spectrofluorimetric method for determination of PXT in terms of its higher sensitivity and wider linear range. The high sensitivity of the method allowed its successful application to the analysis of PXT in spiked human plasma. The proposed method is practical and valuable for its routine application in quality control and clinical laboratories for analysis of PXT.

Sign in / Sign up

Export Citation Format

Share Document