scholarly journals RADIOMETRIC PROPERTIES OFAGRICULTURAL PERMEABLE COVERINGS

2010 ◽  
Vol 41 (2) ◽  
pp. 1 ◽  
Author(s):  
Sergio Castellano ◽  
Silke Hemming ◽  
Giovanni Russo ◽  
Vida Mohammadkhani ◽  
Gert-Jan Glam Swinkels ◽  
...  
Keyword(s):  
Open Field ◽  
Three Dimensional ◽  
Field Tests ◽  
Mesh Size ◽  
Integrating Sphere ◽  
Large Size ◽  
Direct Light ◽  
Agricultural Applications ◽  
Set Up ◽  
Radiation Passing

Nets are commonly used for agricultural applications. However, only little is known about the radiometric properties of net types and how to influence them. In order to investigate the influence of net construction parameters on their radiometric properties, a set of radiometric tests were performed on 45 types of agricultural nets. Laboratory tests on large size net samples was performed using a large and a small integrating sphere. Open field radiometric test were carried out by means of an experimental set up (120x120x50 cm) and a full scale shade house. Small differences (less than 5%) occurred between laboratory and open field tests. Results highlighted that the porosity and the mesh size, combined with the colour and secondarily, with the fabric and the kind of threads of the net influenced the shading performance of the net. The colour influenced the spectral distribution of the radiation passing through the net absorbing its complementary colours. Since nets are three-dimensional structures the transmissivity of direct light under different angles of incident of solar radiation changes when installed in the warp or weft direction. Transmissivity could be considered one of the main parameters involved in the agronomic performances of the netting system.

Deformation Analysis of Hydrostatic Thrust Bearing under Different Load

2014 ◽  
Vol 494-495 ◽  
pp. 583-586
Author(s):  
Yan Qin Zhang ◽  
Li Guo Fan ◽  
Yao Chen ◽  
Rui Li ◽  
Tian Zheng Wu ◽  
...  
Keyword(s):  
Thrust Bearing ◽  
Three Dimensional ◽  
Deformation Analysis ◽  
Hydrostatic Bearing ◽  
Deformation Problem ◽  
Large Size ◽  
Set Up ◽  
Load Simulation ◽  
Bearing Structure ◽  
Ansys Workbench

In order to solve deformation problem of large size hydrostatic thrust bearing under different load. Simulation model of fan cavity hydrostatic thrust bearing, three-dimensional mathematical model in guide rail is set up. Using CFD principle, FIUENT and ANSYS Workbench software, temperature field, pressure field and deformation field of hydrostatic bearing is simulated. Hydrostatic bearing deformation under different load conditions can be simulated and the lubrication characteristic is forecast in advance through this method. It provides valuable theoretical basis for hydrostatic bearing structure parameter optimization of oil cavity and worktable.

Central ossifying fibroma of mandible

2020 ◽  
Vol 13 (12) ◽  
pp. e239286
Author(s):  
Kumar Nilesh ◽  
Prashant Punde ◽  
Nitin Shivajirao Patil ◽  
Amol Gautam
Keyword(s):  
Fibrous Tissue ◽  
Three Dimensional ◽  
Facial Asymmetry ◽  
Ossifying Fibroma ◽  
Mandible Reconstruction ◽  
Three Dimensional Printing ◽  
Osseous Lesion ◽  
Large Size ◽  
Dimensional Printing

Ossifying fibroma (OF) is a rare, benign, fibro-osseous lesion of the jawbone characterised by replacement of the normal bone with fibrous tissue. The fibrous tissue shows varying amount of calcified structures resembling bone and/or cementum. The central variant of OF is rare, and shows predilection for mandible among the jawbone. Although it is classified as fibro-osseous lesion, it clinically behaves as a benign tumour and can grow to large size, causing bony swelling and facial asymmetry. This paper reports a case of large central OF of mandible in a 40-year-old male patient. The lesion was treated by segmental resection of mandible. Reconstruction of the surgical defect was done using avascular fibula bone graft. Role of three-dimensional printing of jaw and its benefits in surgical planning and reconstruction are also highlighted.

scholarly journals Vibration characteristics of triple-gear-rotor system in compressed air energy storage under variable torque load

2021 ◽  
Vol 104 (1) ◽  
pp. 003685042098705
Author(s):  
Xinran Wang ◽  
Yangli Zhu ◽  
Wen Li ◽  
Dongxu Hu ◽  
Xuehui Zhang ◽  
...  
Keyword(s):  
Large Scale ◽  
Three Dimensional ◽  
Element Model ◽  
Rotor System ◽  
Dynamic Responses ◽  
System Response ◽  
Rotating Speed ◽  
Torque Load ◽  
Set Up ◽  
Two Stages

This paper focuses on the effects of the off-design operation of CAES on the dynamic characteristics of the triple-gear-rotor system. A finite element model of the system is set up with unbalanced excitations, torque load excitations, and backlash which lead to variations of tooth contact status. An experiment is carried out to verify the accuracy of the mathematical model. The results show that when the system is subjected to large-scale torque load lifting at a high rotating speed, it has two stages of relatively strong periodicity when the torque load is light, and of chaotic when the torque load is heavy, with the transition between the two states being relatively quick and violent. The analysis of the three-dimensional acceleration spectrum and the meshing force shows that the variation in the meshing state and the fluctuation of the meshing force is the basic reasons for the variation in the system response with the torque load. In addition, the three rotors in the triple-gear-rotor system studied show a strong similarity in the meshing states and meshing force fluctuations, which result in the similarity in the dynamic responses of the three rotors.

Optimum Design for the Frame of Open Type Abrasive Flow Polish Machine

2012 ◽  
Vol 497 ◽  
pp. 89-93
Author(s):  
Liang Liang Yuan ◽  
Ke Hua Zhang ◽  
Li Min
Keyword(s):  
Finite Element ◽  
Natural Frequency ◽  
Finite Element Methods ◽  
Optimization Design ◽  
Low Cost ◽  
Three Dimensional ◽  
Force Model ◽  
Optimization Analysis ◽  
Open Type ◽  
Set Up

In order to process heterotype hole of workpiece precisely, an open abrasive flow polish machine is designed, and the optimization design of machine frame is done for low cost. Firstly, basing on the parameters designed with traditional ways, three-dimensional force model is set up with the soft of SolidWorks. Secondly, the statics and modal analysis for machine body have been done in Finite element methods (FEM), and then the optimization analysis of machine frame has been done. At last, the model of rebuild machine frame has been built. Result shows that the deformation angle value of machine frame increased from 0.72′ to 1.001′, the natural frequency of the machine decreased from 75.549 Hz to 62.262 Hz, the weight of machine decreased by 74.178 Kg after optimization. It meets the strength, stiffness and angel stiffness requirement of machine, reduces the weight and cost of machine.

scholarly journals The Sankara Nethralaya Tamil Nadu Essilor Myopia (STEM) Study—Defining a Threshold for Non-Cycloplegic Myopia Prevalence in Children

2021 ◽  
Vol 10 (6) ◽  
pp. 1215
Author(s):  
Aparna Gopalakrishnan ◽  
Jameel Rizwana Hussaindeen ◽  
Viswanathan Sivaraman ◽  
Meenakshi Swaminathan ◽  
Yee Ling Wong ◽  
...  
Keyword(s):  
Open Field ◽  
Tamil Nadu ◽  
Mean Difference ◽  
School Vision ◽  
Elite School ◽  
Prevalence Estimates ◽  
The Mean ◽  
Clinically Significant ◽  
Set Up ◽  
Definition Of

The aim of this study was to investigate the agreement between cycloplegic and non-cycloplegic autorefraction with an open-field auto refractor in a school vision screening set up, and to define a threshold for myopia that agrees with the standard cycloplegic refraction threshold. The study was conducted as part of the Sankara Nethralaya Tamil Nadu Essilor Myopia (STEM) study, which investigated the prevalence, incidence, and risk factors for myopia among children in South India. Children from two schools aged 5 to 15 years, with no ocular abnormalities and whose parents gave informed consent for cycloplegic refraction were included in the study. All the children underwent visual acuity assessment (Pocket Vision Screener, Elite school of Optometry, India), followed by non-cycloplegic and cycloplegic (1% tropicamide) open-field autorefraction (Grand Seiko, WAM-5500). A total of 387 children were included in the study, of whom 201 were boys. The mean (SD) age of the children was 12.2 (±2.1) years. Overall, the mean difference between cycloplegic and non-cycloplegic spherical equivalent (SE) open-field autorefraction measures was 0.34 D (limits of agreement (LOA), 1.06 D to −0.38 D). For myopes, the mean difference between cycloplegic and non-cycloplegic SE was 0.13 D (LOA, 0.63D to −0.36D). The prevalence of myopia was 12% (95% CI, 8% to 15%) using the threshold of cycloplegic SE ≤ −0.50 D, and was 14% (95% CI, 11% to 17%) with SE ≤ −0.50 D using non-cycloplegic refraction. When myopia was defined as SE of ≤−0.75 D under non-cycloplegic conditions, there was no difference between cycloplegic and non-cycloplegic open-field autorefraction prevalence estimates (12%; 95% CI, 8% to 15%; p = 1.00). Overall, non-cycloplegic refraction underestimates hyperopia and overestimates myopia; but for subjects with myopia, this difference is minimal and not clinically significant. A threshold of SE ≤ −0.75 D agrees well for the estimation of myopia prevalence among children when using non-cycloplegic refraction and is comparable with the standard definition of cycloplegic myopic refraction of SE ≤ −0.50 D.

scholarly journals Optical Encryption Based on Computer Generated Holograms in Photopolymer

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1358
Author(s):  
Taihui Wu ◽  
Jianshe Ma ◽  
Chengchen Wang ◽  
Haibei Wang ◽  
Liangcai Cao ◽  
...  
Keyword(s):  
High Speed ◽  
Three Dimensional ◽  
Angular Spectrum ◽  
Quick Response ◽  
Response Code ◽  
Optical Encryption ◽  
Large Size ◽  
Quick Response Code ◽  
Computer Generated Holograms ◽  
Encryption Method

An optical encryption method based on computer generated holograms printing of photopolymer is presented. Fraunhofer diffraction is performed based on the Gerchberg-Saxton algorithm, and a hologram of the Advanced Encryption Standard encrypted Quick Response code is generated to record the ciphertext. The holograms of the key and the three-dimensional image are generated by the angular spectrum diffraction algorithm. The experimental results show that large-size encrypted Quick Response (QR) code and miniature keys can be printed in photopolymers, which has good application prospects in optical encryption. This method has the advantages of high-density storage, high speed, large fault tolerance, and anti-peeping.

scholarly journals Mesh size sensitivity analysis for interlaminar fracture of the fiber-reinforced laminated composites

2019 ◽  
Vol 14 ◽  
pp. 155892501988346 ◽  
Author(s):  
Fatih Daricik
Keyword(s):  
Crack Closure ◽  
Strain Energy ◽  
Three Dimensional ◽  
Laminated Composite ◽  
Mesh Size ◽  
Strain Energy Release ◽  
Virtual Crack Closure Technique ◽  
Closure Technique ◽  
Interlaminar Fracture ◽  
Element Size

The virtual crack closure technique is a well-known finite element–based numerical method used to simulate fractures and it suits well to both of two-dimensional and three-dimensional interlaminar fracture analysis. In particular, strain energy release rate during a three-dimensional interlaminar fracture of laminated composite materials can successfully be computed using the virtual crack closure technique. However, the element size of a numerical model is an important concern for the success of the computation. The virtual crack closure technique analysis with a finer mesh converges the numerical results to experimental ones although such a model may need excessive modeling and computing times. Since, the finer element size through a crack path causes oscillation of the stresses at the free ends of the model, the plies in the delaminated zone may overlap. To eliminate this problem, the element size for the virtual crack closure technique should be adjusted to ascertain converged yet not oscillating results with an admissible processing time. In this study, mesh size sensitivity of the virtual crack closure technique is widely investigated for mode I and mode II interlaminar fracture analyses of laminated composite material models by considering experimental force and displacement responses of the specimens. Optimum sizes of the finite elements are determined in terms of the force, the displacement, and the strain energy release rate distribution along the width of the model.

scholarly journals Computer-aided design of multi-purpose steel headframes for mines with a new technical level

2020 ◽  
Vol 174 ◽  
pp. 01048
Author(s):  
Elena Kassikhina ◽  
Vladimir Pershin ◽  
Nina Rusakova
Keyword(s):  
Cross Sections ◽  
Computer Aided Design ◽  
Information Technologies ◽  
Three Dimensional ◽  
Numerical Control ◽  
Technical Level ◽  
Resource Saving ◽  
Existing Structures ◽  
Set Up ◽  
Aided Design

The existing structures of the steel sinking headgear and permanent headframe do not meet the requirements of resource saving (metal consumption and manpower input at installation), and the present methods of the headframe designing do not fully reflect recent possibilities of applying of the advanced information technologies. Technical level of the modern software makes it possible for designers to set up multiple numerical experiments to create a computer simulation that allows solving the problem without field and laboratory experiments, and therefore without special costs. In this regard, a mathematical simulation has been developed and based on it, software to select cross-sections of multi- purpose steel headframe elements and to calculate proper weight of its metal structures depending on the characteristics and hoisting equipment. A headframe drawing is displayed, as the results of the software work, including list of elements, obtained optimal hoisting equipment in accordance with the initial data. The software allows speeding up graphic work and reducing manpower input on calculations and paper work. The software allows developing a three-dimensional image of the structure and its functional blocks, based on the obtained initial parameters, as well as developing control software for units with numerical control (NC) in order to manufacture multi-purpose headframes.

Study on Magnetic Barrel Machine Equipped with Three-Dimensional Arrangement of Magnets

2007 ◽  
Vol 329 ◽  
pp. 761-766 ◽  
Author(s):  
Y. Zhang ◽  
Masato Yoshioka ◽  
Shin-Ichiro Hira
Keyword(s):  
High Speed ◽  
Permanent Magnets ◽  
Three Dimensional ◽  
Video Camera ◽  
High Speed Video ◽  
High Speed Video Camera ◽  
The Media ◽  
Set Up

At present, a commercially available magnetic barrel machine equipped with permanent magnets has some faults arising from constructional reason. That is, grinding or finishing ability is different from place to place in the machining region, resulting in the limitation on the region we can use in the container of workpieces. Therefore, in this research, authors made the new magnetic barrel machine equipped with three dimensional (3D) magnet arrangement to overcome these faults. The grinding ability of the new 3D magnetic barrel machine converted was experimentally examined, and compared with that of the traditional magnetic barrel machine. As a result, it was shown that we can use much broader region in the new 3D machine. It was also shown that the grinding ability became higher. The distribution of barrel media in action was recorded by means of a high speed video camera. It was clarified that the media rose up higher and were distributed more uniformly in the container by the effect of the magnet block newly set up. It was supposed that this must be the reason for the above-mentioned improvement of grinding ability.

Exploring Nature's plasticity with a flexible probing tool, and finding new ways for its electronic distribution

2002 ◽  
Vol 30 (2) ◽  
pp. 78-82 ◽  
Author(s):  
M. Beier ◽  
M. Baum ◽  
H. Rebscher ◽  
R. Mauritz ◽  
A. Wixmerten ◽  
...  
Keyword(s):  
Three Dimensional ◽  
In Situ Synthesis ◽  
Light Modulation ◽  
Genomic Assays ◽  
Electronic Distribution ◽  
Spatial Light Modulation ◽  
Microarray Fabrication ◽  
Set Up ◽  
Microarray Format

Concepts and results are described for the use of a single, but extremely flexible, probing tool to address a wide variety of genomic questions. This is achieved by transforming genomic questions into a software file that is used as the design scheme for potentially any genomic assay in a microarray format. Microarray fabrication takes place in three-dimensional microchannel reaction carriers by in situ synthesis based on spatial light modulation. This set-up allows for maximum flexibility in design and realization of genomic assays. Flexibility is achieved at the molecular, genomic and assay levels. We have applied this technology to expression profiling and genotyping experiments.

Sign in / Sign up

Export Citation Format

Share Document