Impact of Grain Structure and Material Properties on Via Extrusion in 3D Interconnects

2015 ◽  
Vol 12 (3) ◽  
pp. 118-122 ◽  
Author(s):  
Tengfei Jiang ◽  
Chenglin Wu ◽  
Jay Im ◽  
Rui Huang ◽  
Paul S. Ho
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Grain Size ◽  
Finite Element ◽  
Analytical Model ◽  
Material Properties ◽  
Grain Structure ◽  
Element Analysis ◽  
Silicon Vias ◽  
The Relationship

In this article, the effects of Cu microstructure on the mechanical properties and extrusion of through-silicon vias (TSVs) were studied based on two types of TSVs with different microstructure. A direct correlation was found between the grain size and the mechanical properties of the vias. Both an analytical model and finite element analysis (FEA) were used to establish the relationship between the mechanical properties and via extrusion. The effect of via/Si interface on extrusion was also studied by FEA. The results suggest small and uniform grains in the Cu vias, as well as stronger interfaces between the via and Si led to smaller via extrusion, and are thus preferable for reduced via extrusion failure and improved TSV reliability.

Impact of Grain Structure and Material Properties on Via Extrusion in 3-D Interconnects

2014 ◽  
Vol 2014 (1) ◽  
pp. 000008-000012
Author(s):  
Tengfei Jiang ◽  
Chenglin Wu ◽  
Jay Im ◽  
Rui Huang ◽  
Paul S. Ho
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Analytical Model ◽  
Material Properties ◽  
Grain Structure ◽  
Silicon Vias ◽  
The Relationship

In this paper, the effects of Cu microstructure on the mechanical properties and extrusion of though-silicon vias (TSVs) were studied based on two types of TSVs with different microstructure. A direct correlation was found between the grain size and the mechanical properties of the vias. Both an analytical model and FEA were used to establish the relationship between the mechanical properties and via extrusion. The effect of via/Si interface on extrusion was also studied by FEA. The results suggest small and uniform grains in the Cu vias, as well as stronger interfaces between the via and Si led to smaller via extrusion, and are thus preferable for reduced via extrusion failure and improved TSV reliability.

scholarly journals Finite element analysis relating shape, material properties, and dimensions of taenioglossan radular teeth with trophic specialisations in Paludomidae (Gastropoda)

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Wencke Krings ◽  
Jordi Marcé-Nogué ◽  
Stanislav N. Gorb
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Material Properties ◽  
Stress And Strain ◽  
Plant Surface ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Force Volume ◽  
General Size

AbstractThe radula, a chitinous membrane with embedded tooth rows, is the molluscan autapomorphy for feeding. The morphologies, arrangements and mechanical properties of teeth can vary between taxa, which is usually interpreted as adaptation to food. In previous studies, we proposed about trophic and other functional specialisations in taenioglossan radulae from species of African paludomid gastropods. These were based on the analysis of shape, material properties, force-resistance, and the mechanical behaviour of teeth, when interacting with an obstacle. The latter was previously simulated for one species (Spekia zonata) by the finite-element-analysis (FEA) and, for more species, observed in experiments. In the here presented work we test the previous hypotheses by applying the FEA on 3D modelled radulae, with incorporated material properties, from three additional paludomid species. These species forage either on algae attached to rocks (Lavigeria grandis), covering sand (Cleopatra johnstoni), or attached to plant surface and covering sand (Bridouxia grandidieriana). Since the analysed radulae vary greatly in their general size (e.g. width) and size of teeth between species, we additionally aimed at relating the simulated stress and strain distributions with the tooth sizes by altering the force/volume. For this purpose, we also included S. zonata again in the present study. Our FEA results show that smaller radulae are more affected by stress and strain than larger ones, when each tooth is loaded with the same force. However, the results are not fully in congruence with results from the previous breaking stress experiments, indicating that besides the parameter size, more mechanisms leading to reduced stress/strain must be present in radulae.

scholarly journals Finite Element Analysis Relating Shape, Material Properties, and Dimensions of Taenioglossan Radular Teeth with Trophic Specialisations in Paludomidae (Gastropoda)

2021 ◽  
Author(s):  
Wencke Krings ◽  
Jordi Marcé-Nogué ◽  
Stanislav N. Gorb
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Mechanical Behaviour ◽  
Material Properties ◽  
Stress And Strain ◽  
Plant Surface ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Force Volume

Abstract The radula, a chitinous membrane with embedded tooth rows, is the molluscan autapomorphy for feeding. The morphologies, arrangements and mechanical properties of teeth can vary between taxa, which is usually interpreted as adaptation to food. In previous studies, we proposed about trophic and other functional specialisations in taenioglossan radulae from species of African paludomid gastropods. These were based on the analysis of shape, material properties, force-resistance, and the mechanical behaviour of teeth, when interacting with an obstacle, which was previously simulated for one species (Spekia) by the finite-element-analysis (FEA) and, for more species, observed in experiments. In the here presented work, we test the previous hypotheses by applying the FEA on 3D modelled radulae, with incorporated material properties, from three additional paludomid species. These species forage either on algae attached to rocks (Lavigeria), covering sand (Cleopatra), or attached to plant surface and covering sand (Bridouxia). Since the analysed radulae vary greatly in their size between species, we additionally aimed at relating the simulated stress and strain distributions with the tooth sizes by altering the force/volume. For this purpose, we also included Spekia again in the present study. Our FEA results show that smaller radulae are more affected by stress and strain than larger ones, when each tooth is loaded with the same force. However, the results are not fully in congruence with results from the previous breaking stress experiments, indicating that besides the parameter size, more mechanisms leading to reduced stress/strain must be present in radulae.

Research on Mechanical Properties and Simulation of Straw-Biodegradable Tableware

2011 ◽  
Vol 101-102 ◽  
pp. 1096-1100
Author(s):  
Quan Rong Jing ◽  
Feng Xu ◽  
De Gao
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Optimal Solution ◽  
Reference Method ◽  
Specific Load ◽  
Analysis Software ◽  
Element Analysis ◽  
The Relationship

Through the test of mechanical properties of the straw-biodegradable tableware, the relationship between performance and processing technology was analyzed and the optimal solution was obtained. And using finite element analysis software, the internal stress distribution under the specific load was obtained based on mechanical properties, more valuable reference method about tableware design was provided through studying the changing intensity.

Mapping the Mechanical Properties of Cancellous Bone from the Femoral Head

2015 ◽  
Vol 801 ◽  
pp. 273-277
Author(s):  
Karla Noemy Kun ◽  
Lorand Kun ◽  
Ramona Nagy ◽  
Karoly Menyhardt ◽  
Dana Silaghi-Perju ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Femoral Head ◽  
Cancellous Bone ◽  
Material Properties ◽  
Compression Testing ◽  
Experimental Program ◽  
Element Analysis

This work presents an experimental program to determine the mechanical properties of cancellous bone in the femoral head as a function of location. To achieve this several specimens of cancellous bone of approximately 10 mm height and 10 mm diameter were obtained from one human femoral head, starting the sampling from its main loading compressive direction. All specimens underwent compression testing in order to determine the mechanical properties of each specimen and thus a properties map of the cancellous bone in the femoral head was obtained. Based on the results a parametric file with material properties was created in order to be used by professionals in finite element analysis programs.

Inverse Method to Determine Mechanical Properties of Thin Film by Nanoindentation and Finite Element Analysis

2006 ◽  
Vol 326-328 ◽  
pp. 219-222 ◽  
Author(s):  
Dong Cheon Baek ◽  
Soon Bok Lee
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Young’S Modulus ◽  
Material Properties ◽  
Inverse Method ◽  
Young's Modulus ◽  
Displacement Curve ◽  
Element Analysis

As a reliable tool to measure the Young’s modulus, nanoindention technique has been used widely recently. In this paper, nanoindetation technique was overviewed with its advantage and limitation and a new method was proposed to determine material properties of film, i.e. both Young’s modulus E and Poisson’s ratio ν from load-displacement curve of shallow-depth indentation using ‘inverse method’.

scholarly journals New approach for getting better accuracy with mesh dependent material properties

2018 ◽  
Vol 9 ◽  
pp. A2
Author(s):  
Qiu-Ping Zhou ◽  
Hua Ding
Keyword(s):  
Finite Element Method ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Material Properties ◽  
Optimal Solution ◽  
Mesh Size ◽  
Element Analysis ◽  
New Approach ◽  
The Finite Element Analysis ◽  
The Relationship

Based on the relationship between finite element (FE) solution and mesh size, a new approach based on mesh depending on the material properties is proposed to make the finite element analysis results more efficient and more close to the optimal solution. This optimal solution is often evaluated either by experiment or by finite element method (FEM). At the opposite of the accuracy obtained by sensitivities analysis of the FEM which requires time-consuming, our approach allows getting the optimal meshing based on the material properties.

Finite Element Analysis of Reinforced Concrete Beams with Exterior FRP Shell

2011 ◽  
Vol 243-249 ◽  
pp. 1461-1465
Author(s):  
Chuan Min Zhang ◽  
Chao He Chen ◽  
Ye Fan Chen
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Contact Interface ◽  
Accurate Calculation ◽  
Element Analysis

The paper makes an analysis of the reinforced concrete beams with exterior FRP Shell in Finite Element, and compares it with the test results. The results show that, by means of this model, mechanical properties of reinforced concrete beams with exterior FRP shell can be predicted better. However, the larger the load, the larger deviation between calculated values and test values. Hence, if more accurate calculation is required, issues of contact interface between the reinforced concrete beams and the FRP shell should be taken into consideration.

Sign in / Sign up

Export Citation Format

Share Document