Tolerance-optimized RF structures in LTCC for mm-wave frequencies applications

2015 ◽  
Vol 2015 (CICMT) ◽  
pp. 000073-000076 ◽  
Author(s):  
Jordi Balcells-Ventura ◽  
Tobias Klein ◽  
Peter Uhlig ◽  
Carsten Günner ◽  
Reinhard Kulke
Keyword(s):  
Low Temperature ◽  
Power Splitter ◽  
Frequency Bands ◽  
Embedded Passives ◽  
Fabrication Tolerances

Low Temperature Co-fired Ceramic (LTCC) is a well established technology for microwave space products and RF structures and it is a good candidate for these new frequency bands. Embedded passives are available to increase the density of integration even more. At higher frequencies structures become smaller and more prone to process tolerances. This challenge is addressed here with two novel mm-wave tolerance-optimized RF concepts in LTCC: load termination and Gysel power splitter. The concept presented here minimizes the effect of fabrication tolerances to provide stable RF response.

The Infrared Spectra of Amino Acids and Some Simple Polypeptides to 33 cm−1 at Room and Liquid Nitrogen Temperatures

1971 ◽  
Vol 25 (2) ◽  
pp. 175-182 ◽  
Author(s):  
William R. Feairheller ◽  
J. T. Miller
Keyword(s):  
Amino Acids ◽  
Low Temperature ◽  
Ir Spectra ◽  
Liquid Nitrogen ◽  
Infrared Spectra ◽  
Low Temperatures ◽  
Low Frequency ◽  
Absorption Bands ◽  
Frequency Bands ◽  
Analytical Information

The ir spectra of a number of amino acids have been studied and the absorption bands in the 400–33 cm−1 region are reported. Spectra were recorded at both room and liquid nitrogen temperatures. It was observed that recording at low temperatures is a useful method for obtaining additional analytical information when the amino acids are in the zwitterion form. Low temperature is also useful in determining the assignment of several of the low frequency bands.

Exsolution and inversion in pigeonite from the Whin Sill, Northern England

1978 ◽  
Vol 36 (1) ◽  
pp. 474-475
Author(s):  
P.P.K. Smith
Keyword(s):  
High Temperature ◽  
Low Temperature ◽  
Homogeneous Nucleation ◽  
Silicate Mineral ◽  
Antiphase Boundaries ◽  
Two Phase ◽  
Primitive Form ◽  
The Core ◽  
Nucleation Mechanisms ◽  
And Inversion

Grains of pigeonite, a calcium-poor silicate mineral of the pyroxene group, from the Whin Sill dolerite have been ion-thinned and examined by TEM. The pigeonite is strongly zoned chemically from the composition Wo8En64FS28 in the core to Wo13En34FS53 at the rim. Two phase transformations have occurred during the cooling of this pigeonite:- exsolution of augite, a more calcic pyroxene, and inversion of the pigeonite from the high- temperature C face-centred form to the low-temperature primitive form, with the formation of antiphase boundaries (APB's). Different sequences of these exsolution and inversion reactions, together with different nucleation mechanisms of the augite, have created three distinct microstructures depending on the position in the grain.In the core of the grains small platelets of augite about 0.02μm thick have farmed parallel to the (001) plane (Fig. 1). These are thought to have exsolved by homogeneous nucleation. Subsequently the inversion of the pigeonite has led to the creation of APB's.

Low temperature x-ray microanalysis of frozen-hydrated tobacco leaves

1984 ◽  
Vol 42 ◽  
pp. 284-285
Author(s):  
S. Edith Taylor ◽  
Patrick Echlin ◽  
May McKoon ◽  
Thomas L. Hayes
Keyword(s):  
Low Temperature ◽  
Lemna Minor ◽  
Root Tips ◽  
Tobacco Leaves ◽  
X Ray ◽  
Whole Cells ◽  
Carbon Coated ◽  
The Right ◽  
Beam Currents ◽  
The University

Low temperature x-ray microanalysis (LTXM) of solid biological materials has been documented for Lemna minor L. root tips. This discussion will be limited to a demonstration of LTXM for measuring relative elemental distributions of P,S,Cl and K species within whole cells of tobacco leaves.Mature Wisconsin-38 tobacco was grown in the greenhouse at the University of California, Berkeley and picked daily from the mid-stalk position (leaf #9). The tissue was excised from the right of the mid rib and rapidly frozen in liquid nitrogen slush. It was then placed into an Amray biochamber and maintained at 103K. Fracture faces of the tissue were prepared and carbon-coated in the biochamber. The prepared sample was transferred from the biochamber to the Amray 1000A SEM equipped with a cold stage to maintain low temperatures at 103K. Analyses were performed using a tungsten source with accelerating voltages of 17.5 to 20 KV and beam currents from 1-2nA.

Bulk standards for low-temperature biological x-ray microanalysis

1984 ◽  
Vol 42 ◽  
pp. 282-283
Author(s):  
P. Echlin ◽  
M. McKoon ◽  
E.S. Taylor ◽  
C.E. Thomas ◽  
K.L. Maloney ◽  
...  
Keyword(s):  
Phase Separation ◽  
Low Temperature ◽  
Analytical Method ◽  
Salt Solutions ◽  
Absolute Concentration ◽  
Cooling Process ◽  
X Ray ◽  
The Absolute ◽  
Analytical Procedures ◽  
Electrical Conductors

Although sections of frozen salt solutions have been used as standards for x-ray microanalysis, such solutions are less useful when analysed in the bulk form. They are poor thermal and electrical conductors and severe phase separation occurs during the cooling process. Following a suggestion by Whitecross et al we have made up a series of salt solutions containing a small amount of graphite to improve the sample conductivity. In addition, we have incorporated a polymer to ensure the formation of microcrystalline ice and a consequent homogenity of salt dispersion within the frozen matrix. The mixtures have been used to standardize the analytical procedures applied to frozen hydrated bulk specimens based on the peak/background analytical method and to measure the absolute concentration of elements in developing roots.

Field ion microscopy

1988 ◽  
Vol 46 ◽  
pp. 434-435
Author(s):  
Gert Ehrlich
Keyword(s):  
Low Temperature ◽  
Sample Surface ◽  
Low Pressure ◽  
Radius Of Curvature ◽  
Field Ion Microscopy ◽  
Phosphor Screen ◽  
Ion Microscopy ◽  
Field Ion Microscope

The field ion microscope, devised by Erwin Muller in the 1950's, was the first instrument to depict the structure of surfaces in atomic detail. An FIM image of a (111) plane of tungsten (Fig.l) is typical of what can be done by this microscope: for this small plane, every atom, at a separation of 4.48Å from its neighbors in the plane, is revealed. The image of the plane is highly enlarged, as it is projected on a phosphor screen with a radius of curvature more than a million times that of the sample. Müller achieved the resolution necessary to reveal individual atoms by imaging with ions, accommodated to the object at a low temperature. The ions are created at the sample surface by ionization of an inert image gas (usually helium), present at a low pressure (< 1 mTorr). at fields on the order of 4V/Å.

High-Vacuum Evaporation and a Cryostage to Observe Fractured Yeast

1988 ◽  
Vol 46 ◽  
pp. 256-257
Author(s):  
William P. Wergin ◽  
Eric F. Erbe ◽  
Eugene L. Vigil
Keyword(s):  
Electron Microscope ◽  
Low Temperature ◽  
Standard Specimen ◽  
High Vacuum ◽  
Specimen Holder ◽  
Sputter Coating ◽  
Fresh Frozen ◽  
Gain Access ◽  
Scanning Electron ◽  
Transfer Device

Investigators have long realized the potential advantages of using a low temperature (LT) stage to examine fresh, frozen specimens in a scanning electron microscope (SEM). However, long working distances (W.D.), thick sputter coatings and surface contamination have prevented LTSEM from achieving results comparable to those from TEM freeze etch. To improve results, we recently modified techniques that involve a Hitachi S570 SEM, an Emscope SP2000 Sputter Cryo System and a Denton freeze etch unit. Because investigators have frequently utilized the fractured E face of the plasmalemma of yeast, this tissue was selected as a standard for comparison in the present study.In place of a standard specimen holder, a modified rivet was used to achieve a shorter W.D. (1 to -2 mm) and to gain access to the upper detector. However, the additional height afforded by the rivet, precluded use of the standard shroud on the Emscope specimen transfer device. Consequently, the sample became heavily contaminated (Fig. 1). A removable shroud was devised and used to reduce contamination (Fig. 2), but the specimen lacked clean fractured edges. This result suggested that low vacuum sputter coating was also limiting resolution.

Observation by HVEM of the martensite transformation and the superconducting transition in Nb3Sn

1988 ◽  
Vol 46 ◽  
pp. 788-789
Author(s):  
M. A. Kirk ◽  
M. C. Baker ◽  
B. J. Kestel ◽  
H. W. Weber
Keyword(s):  
Thin Films ◽  
Low Temperature ◽  
Superconducting State ◽  
Martensite Transformation ◽  
Sputter Deposition ◽  
Diffusion Reaction ◽  
Solute Diffusion ◽  
Superconducting Transition ◽  
Twin Boundaries ◽  
Martensite Structure

It is well known that a number of compound superconductors with the A15 structure undergo a martensite transformation when cooled to the superconducting state. Nb3Sn is one of those compounds that transforms, at least partially, from a cubic to tetragonal structure near 43 K. To our knowledge this transformation in Nb3Sn has not been studied by TEM. In fact, the only low temperature TEM study of an A15 material, V3Si, was performed by Goringe and Valdre over 20 years ago. They found the martensite structure in some foil areas at temperatures between 11 and 29 K, accompanied by faults that consisted of coherent twin boundaries on {110} planes. In pursuing our studies of irradiation defects in superconductors, we are the first to observe by TEM a similar martensite structure in Nb3Sn.Samples of Nb3Sn suitable for TEM studies have been produced by both a liquid solute diffusion reaction and by sputter deposition of thin films.

In situ Tensile Experiments at Low Temperatures on Niobium Single Crystals by H.V.E.M.

1975 ◽  
Vol 33 ◽  
pp. 58-59
Author(s):  
F. H. Louchet ◽  
L. P. Kubin
Keyword(s):  
Electron Microscope ◽  
Transition Temperature ◽  
Low Temperature ◽  
Slip System ◽  
Low Temperatures ◽  
Tensile Axis ◽  
Image Intensifier ◽  
Screw Dislocations ◽  
Source Operation

Experiments have been carried out on the 3 MeV electron microscope in Toulouse. The low temperature straining holder has been previously described Images given by an image intensifier are recorded on magnetic tape.The microtensile niobium samples are cut in a plane with the two operative slip directions [111] and lying in the foil plane. The tensile axis is near [011].Our results concern:- The transition temperature of niobium near 220 K: at this temperature and below an increasing difference appears between the mobilities of the screw and edge portions of dislocations loops. Source operation and interactions between screw dislocations of different slip system have been recorded.

Electron microscopic assays of restriction endonuclease cutting, exonuclease digestion, and hybridization

1984 ◽  
Vol 42 ◽  
pp. 686-687
Author(s):  
Mark Hannibal ◽  
Jacob Varkey ◽  
Michael Beer
Keyword(s):  
Electron Microscope ◽  
Low Temperature ◽  
Restriction Endonuclease ◽  
Double Helix ◽  
Test Material ◽  
Electron Microscopic ◽  
Exonuclease Iii ◽  
Dna Molecule ◽  
Linear Molecules ◽  
Exonuclease Digestion

Workman and Langmore have recently proposed a procedure for isolating particular chromatin fragments. The method requires restriction endonuclease cutting of the chromatin and a probe, their digestion with two exonucleases which leave complimentary single strand termini and low temperature hybridization of these. We here report simple electron microscopic monitoring of the four reactions involved.Our test material was ϕX-174 RF DNA which is cut once by restriction endonuclease Xho I. The conversion of circles to linear molecules was followed in Kleinschmidt spreads. Plate I shows a circular and a linear DNA molecule. The rate of cutting is shown in Figure 1.After completion of the endonuclease cutting, one portion of the DNA was treated with exonuclease III, an enzyme known to digest the 3' terminals of double helical DNA. Aliquots when examined in the electron microscope reveal a decreasing length of double helix and increasing bushes at the ends.

Role of boundaries in the crystallization of amorphous films

1988 ◽  
Vol 46 ◽  
pp. 626-627
Author(s):  
D. A. Smith
Keyword(s):  
Low Temperature ◽  
Amorphous State ◽  
Nucleation And Growth ◽  
Amorphous Films ◽  
Island Nucleation ◽  
Surface Steps ◽  
Transmission Electron ◽  
Component Systems ◽  
Temperature Deposition

The nucleation and growth processes which lead to the formation of a thin film are particularly amenable to investigation by transmission electron microscopy either in situ or subsequent to deposition. In situ studies have enabled the observation of island nucleation and growth, together with addition of atoms to surface steps. This paper is concerned with post-deposition crystallization of amorphous alloys. It will be argued that the processes occurring during low temperature deposition of one component systems are related but the evidence is mainly indirect. Amorphous films result when the deposition conditions such as low temperature or the presence of impurities (intentional or unintentional) preclude the atomic mobility necessary for crystallization. Representative examples of this behavior are CVD silicon grown below about 670°C, metalloids, such as antimony deposited at room temperature, binary alloys or compounds such as Cu-Ag or Cr O2, respectively. Elemental metals are not stable in the amorphous state.

Sign in / Sign up

Export Citation Format

Share Document