scholarly journals Miniature Lowpass Filters in Low Loss 9k7 LTCC

2015 ◽  
Vol 2015 (CICMT) ◽  
pp. 000054-000057
Author(s):  
Steve Dai ◽  
Lung-Hwa Hsieh
Keyword(s):  
Noise Figure ◽  
Low Loss ◽  
High Q ◽  
Rf Components ◽  
Low Pass ◽  
Low Pass Filters ◽  
Quality Factor Q ◽  
Critical Process ◽  
Tape System

DuPont 9k7 low temperature cofired ceramic (LTCC) is a low loss, or high quality factor Q, tape system targeting at radio frequency (RF) applications. This paper reports the effect of a critical process parameter, heating rate, on the densification and dielectric properties of the 9k7 LTCC. The role of competing densification and crystallization during the sintering of 9k7 is discussed. The high Q of DuPont 9K7 can be used to improve RF system performance, for example a better receiver noise figure, by designing embedded passive RF components such as inductors, capacitors and filters. Miniaturized multilayer low pass filters (LPF) with a wide stopband were fabricated to showcase the technology.

High Directivity Couplers using Multilayer Organics (MLO)

2010 ◽  
Vol 2010 (DPC) ◽  
pp. 001931-001947
Author(s):  
George White ◽  
Minu Valayil ◽  
Charlie Russell ◽  
Sid Dalmia
Keyword(s):  
High Dielectric Constant ◽  
Low Cost ◽  
Coupling Coefficients ◽  
Low Loss ◽  
High Q ◽  
Mixed Signal Circuits ◽  
Low Pass ◽  
High Dielectric ◽  
Interconnect Technology ◽  
Q Values

This paper presents the design and fabrication of a stand-alone high directivity coupler using high dielectric constant multilayer organic (MLO) technology. MLO is a low cost high density interconnect technology that allows for the realization of high Q and low loss inductor and capacitor elements that allow for the miniaturization of RF and mixed signal circuits. Q values above 300 have been measured for MLO with costs being lower than both LTCC and TFOS technologies. Low-loss lumped and distributed elements were realized using a novel multilayer build up process that supports both land grid array (LGA) and edge terminations. The couplers which support frequencies between 700 MHz and 2GHz exhibit coupling coefficients above 20db and isolation greater than 40db. The couplers can be combined with low pass harmonic filters in the same technology.

Ku/Ka-band Compact Orthomode Junction with Low Pass Filters for High Power Applications

2015 ◽  
Vol E98.C (2) ◽  
pp. 156-161
Author(s):  
Hidenori YUKAWA ◽  
Koji YOSHIDA ◽  
Tomohiro MIZUNO ◽  
Tetsu OWADA ◽  
Moriyasu MIYAZAKI
Keyword(s):  
High Power ◽  
Ka Band ◽  
Low Pass ◽  
Low Pass Filters

Mathematical Model of Low-Pass Filters

2011 ◽  
Vol 5 (2) ◽  
pp. 155-162
Author(s):  
Jose de Jesus Rubio ◽  
Diana M. Vazquez ◽  
Jaime Pacheco ◽  
Vicente Garcia
Keyword(s):  
Mathematical Model ◽  
Low Pass ◽  
Low Pass Filters

scholarly journals Delay Equivalences in Tuning PID Control for the Double Integrator Plus Dead-Time

Mathematics ◽  
2021 ◽  
Vol 9 (4) ◽  
pp. 328
Author(s):  
Mikulas Huba ◽  
Damir Vrancic
Keyword(s):  
Dead Time ◽  
Pid Controllers ◽  
Noisy Environment ◽  
Advantages And Disadvantages ◽  
Implementation Problem ◽  
Low Pass ◽  
Excellent Control ◽  
Low Pass Filters ◽  
Double Integrator

The paper investigates and explains a new simple analytical tuning of proportional-integrative-derivative (PID) controllers. In combination with nth order series binomial low-pass filters, they are to be applied to the double-integrator-plus-dead-time (DIPDT) plant models. With respect to the use of derivatives, it should be understood that the design of appropriate filters is not only an implementation problem. Rather, it is also critical for the resulting performance, robustness and noise attenuation. To simplify controller commissioning, integrated tuning procedures (ITPs) based on three different concepts of filter delay equivalences are presented. For simultaneous determination of controller + filter parameters, the design uses the multiple real dominant poles method. The excellent control loop performance in a noisy environment and the specific advantages and disadvantages of the resulting equivalences are discussed. The results show that none of them is globally optimal. Each of them is advantageous only for certain noise levels and the desired degree of their filtering.

scholarly journals 1.0 V-0.18 µm CMOS Tunable Low Pass Filters with 73 dB DR for On-Chip Sensing Acquisition Systems

Electronics ◽  
2021 ◽  
Vol 10 (5) ◽  
pp. 563
Author(s):  
Jorge Pérez-Bailón ◽  
Belén Calvo ◽  
Nicolás Medrano
Keyword(s):  
Power Consumption ◽  
Dynamic Range ◽  
Low Voltage ◽  
Cutoff Frequency ◽  
Cmos Technology ◽  
Active Area ◽  
Current Steering ◽  
Low Pass ◽  
On Chip ◽  
Low Pass Filters

This paper presents a new approach based on the use of a Current Steering (CS) technique for the design of fully integrated Gm–C Low Pass Filters (LPF) with sub-Hz to kHz tunable cut-off frequencies and an enhanced power-area-dynamic range trade-off. The proposed approach has been experimentally validated by two different first-order single-ended LPFs designed in a 0.18 µm CMOS technology powered by a 1.0 V single supply: a folded-OTA based LPF and a mirrored-OTA based LPF. The first one exhibits a constant power consumption of 180 nW at 100 nA bias current with an active area of 0.00135 mm2 and a tunable cutoff frequency that spans over 4 orders of magnitude (~100 mHz–152 Hz @ CL = 50 pF) preserving dynamic figures greater than 78 dB. The second one exhibits a power consumption of 1.75 µW at 500 nA with an active area of 0.0137 mm2 and a tunable cutoff frequency that spans over 5 orders of magnitude (~80 mHz–~1.2 kHz @ CL = 50 pF) preserving a dynamic range greater than 73 dB. Compared with previously reported filters, this proposal is a competitive solution while satisfying the low-voltage low-power on-chip constraints, becoming a preferable choice for general-purpose reconfigurable front-end sensor interfaces.

CURRENT-MODE ACTIVE-C FILTER EMPLOYING REDUCED NUMBER OF CCCII+s

2007 ◽  
Vol 16 (04) ◽  
pp. 507-516 ◽  
Author(s):  
SHAHRAM MINAEI ◽  
ERKAN YUCE
Keyword(s):  
Current Mode ◽  
Pass Band ◽  
Passive Component ◽  
Resistorless Filter ◽  
Low Pass ◽  
Component Matching ◽  
Band Pass ◽  
High Output Impedance ◽  
Quality Factor Q ◽  
High Pass

In this paper, a universal current-mode second-order active-C filter for simultaneously realizing low-pass, band-pass and high-pass responses is proposed. The presented filter employs only three plus-type second-generation current-controlled conveyors (CCCII+s). This filter needs no critical active and passive component matching conditions and no additional active and passive elements for realizing high output impedance low-pass, band-pass and high-pass characteristics. The angular resonance frequency (ω0) and quality factor (Q) of the proposed resistorless filter can be tuned electronically. To verify the theoretical analysis and to exhibit the performance of the proposed filter, it is simulated with SPICE program.

scholarly journals Noise-Reducing Fabric Electrode for ECG Measurement

Sensors ◽  
2021 ◽  
Vol 21 (13) ◽  
pp. 4305
Author(s):  
Takamasa Terada ◽  
Masahiro Toyoura ◽  
Takahide Sato ◽  
Xiaoyang Mao
Keyword(s):  
Special Structure ◽  
Electrode Impedance ◽  
Electrode Structure ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Chip Type ◽  
Low Pass ◽  
Filter Fabric

In this work, we propose a fabric electrode with a special structure that can play the role of a noise reduction filter. Fabric electrodes made of the conductive fabric have been used for long-term ECG measurements because of their flexibility and non-invasiveness; however, due to the large impedance between the skin and the fabric electrodes, noise is easily introduced into the ECG signal. In contrast to conventional work, in which chip-type passive elements are glued to the electrode to reduce noise, the proposed electrode can obtain a noise-reduced ECG by changing the structure of fabric. Specifically, the proposed electrode was folded multiple times to form a capacitor with a capacitance of about 3 nF. It is combined with the skin-electrode impedance to form a low-pass filter. In the experiment, we made a prototype of the electrodes and measured ECG at rest and during EMG-induced exercise. As a result, the SNR values at rest and during exercise were improved about 12.02 and 10.29 , respectively, compared with the fabric electrode without special structure. In conclusion, we have shown that changing the fabric electrode structure effectively removes noise in ECG measurement.

scholarly journals Wideband Reconfigurable Integrated Low-Pass Filter for 5G Compatible Software Defined Radio Solutions

Electronics ◽  
2021 ◽  
Vol 10 (6) ◽  
pp. 734
Author(s):  
Karolis Kiela ◽  
Marijan Jurgo ◽  
Vytautas Macaitis ◽  
Romualdas Navickas
Keyword(s):  
Software Defined Radio ◽  
Dynamic Range ◽  
Noise Figure ◽  
Harmonic Distortion ◽  
Cmos Process ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Filter Performance ◽  
Low Pass ◽  
Bandwidth Tuning

This article presents a wideband reconfigurable integrated low-pass filter (LPF) for 5G NR compatible software-defined radio (SDR) solutions. The filter uses Active-RC topology to achieve high linearity performance. Its bandwidth can be tuned from 2.5 MHz to 200 MHz, which corresponds to a tuning ratio of 92.8. The order of the filter can be changed between the 2nd, 4th, or 6th order; it has built-in process, voltage, and temperature (PVT) compensation with a tuning range of ±42%; and power management features for optimization of the filter performance across its entire range of bandwidth tuning. Across its entire order, bandwidth, and power configuration range, the filter achieves in-band input-referred third-order intercept point (IIP3) between 32.7 dBm and 45.8 dBm, spurious free dynamic range (SFDR) between 63.6 dB and 79.5 dB, 1 dB compression point (P1dB) between 9.9 dBm and 14.1 dBm, total harmonic distortion (THD) between −85.6 dB and −64.5 dB, noise figure (NF) between 25.9 dB and 31.8 dB and power dissipation between 1.19 mW and 73.4 mW. The LPF was designed and verified using 65 nm CMOS process; it occupies a 0.429 mm2 area of silicon and uses a 1.2 V supply.

Sign in / Sign up

Export Citation Format

Share Document