How Mitigation Techniques Affect Reliability Results for BGAs

2016 ◽  
Vol 2016 (DPC) ◽  
pp. 001992-002017
Author(s):  
Greg Caswell ◽  
Melissa Keener
Keyword(s):  
Coefficient Of Thermal Expansion ◽  
Operating Conditions ◽  
The Other ◽  
Lead Free ◽  
Mechanical Shock ◽  
Sinusoidal Vibration ◽  
Shock Testing ◽  
Mitigation Techniques ◽  
Lead Free Solders ◽  
Mitigation Technique

Since 2006 RoHS requirements have required lead free solders to take the place of tin-lead solders in electronics. The problem is that in some environments the lead free solders are less reliable than the older tin-lead solders. One of the ways to solve this problem is to corner stake, edge bond or underfill the components. When considering what mitigation technique and material to use, the operating conditions must be characterized. The temperature range is important when selecting a material to use since the glass transition temperature (Tg) and coefficient of thermal expansion (CTE) are important properties. If improperly chosen, the mitigation material can cause more failures than an unmitigated component. This study focused on 208 I/O BGAs on a 4 layer FR4 board. There were three solders tested; two lead free (SAC305 and SN100C) and one leaded (SnPb). Three mitigation techniques were tested: corner staking, edge bonding, and underfilling. Each of these techniques had two mitigation materials tested. One material was reworkable and the other was not. The boards were subjected to mechanical shock testing and sinusoidal vibration testing until failure. The results of the testing show that no one mitigation technique is best for all of the conditions tested. The same is true for the mitigation material. The best choice of mitigation technique and material is application dependent.

How Mitigation Techniques Affect Reliability Results for BGAs

2016 ◽  
Vol 2016 (1) ◽  
pp. 000134-000138
Author(s):  
Greg Caswell ◽  
Melissa Keener (Black and Decker)
Keyword(s):  
Coefficient Of Thermal Expansion ◽  
Operating Conditions ◽  
The Other ◽  
Lead Free ◽  
Mechanical Shock ◽  
Sinusoidal Vibration ◽  
Shock Testing ◽  
Mitigation Techniques ◽  
Lead Free Solders ◽  
Mitigation Technique

Abstract Since 2006 RoHS requirements have required lead free solders to take the place of tin-lead solders in electronics. The problem is that in some environments the lead free solders are less reliable than the older tin-lead solders. One of the ways to solve this problem is to corner stake, edge bond or underfill the components. When considering what mitigation technique and material to use, the operating conditions must be characterized. The temperature range is important when selecting a material to use since the glass transition temperature (Tg) and coefficient of thermal expansion (CTE) are important properties. If improperly chosen, the mitigation material can cause more failures than an unmitigated component. This study focused on 208 I/O BGAs on a 4 layer FR4 board. There were three solders tested; two lead free (SAC305 and SN100C) and one leaded (SnPb). Three mitigation techniques were tested: corner staking, edge bonding, and underfilling. Each of these techniques had two mitigation materials tested. One material was reworkable and the other was not. The boards were subjected to mechanical shock testing and sinusoidal vibration testing until failure. The results of the testing show that no one mitigation technique is best for all of the conditions tested. The same is true for the mitigation material. The best choice of mitigation technique and material is application dependent.

Effect of aluminum content on structure, transport and mechanical properties of Sn-Zn eutectic lead free solder alloy rapidly solidified from melt.

2015 ◽  
Vol 10 (1) ◽  
pp. 2641-2648
Author(s):  
Rizk Mostafa Shalaby ◽  
Mohamed Munther ◽  
Abu-Bakr Al-Bidawi ◽  
Mustafa Kamal
Keyword(s):  
Mechanical Properties ◽  
Melting Point ◽  
Lead Free ◽  
Al Alloy ◽  
Lead Free Solder ◽  
Pronounced Increase ◽  
Mass Unit ◽  
Size Refinement ◽  
Free Solder ◽  
Lead Free Solders

The greatest advantage of Sn-Zn eutectic is its low melting point (198 oC) which is close to the melting point. of Sn-Pb eutectic solder (183 oC), as well as its low price per mass unit compared with Sn-Ag and Sn-Ag-Cu solders. In this paper, the effect of 0.0, 1.0, 2.0, 3.0, 4.0, and 5.0 wt. % Al as ternary additions on melting temperature, microstructure, microhardness and mechanical properties of the Sn-9Zn lead-free solders were investigated. It is shown that the alloying additions of Al at 4 wt. % to the Sn-Zn binary system lead to lower of the melting point to 195.72 ˚C.  From x-ray diffraction analysis, an aluminium phase, designated α-Al is detected for 4 and 5 wt. % Al compositions. The formation of an aluminium phase causes a pronounced increase in the electrical resistivity and microhardness. The ternary Sn-9Zn-2 wt.%Al exhibits micro hardness superior to Sn-9Zn binary alloy. The better Vickers hardness and melting points of the ternary alloy is attributed to solid solution effect, grain size refinement and precipitation of Al and Zn in the Sn matrix.  The Sn-9%Zn-4%Al alloy is a lead-free solder designed for possible drop-in replacement of Pb-Sn solders.  

Shear Strength and Dsc Analysis of High-Temperature Solders

2013 ◽  
Vol 58 (2) ◽  
pp. 529-533 ◽  
Author(s):  
R. Koleňák ◽  
M. Martinkovič ◽  
M. Koleňáková
Keyword(s):  
Shear Strength ◽  
High Temperature ◽  
Lead Free ◽  
Dsc Analysis ◽  
Ultrasonic Activation ◽  
Metallic Substrates ◽  
Cu Substrate ◽  
Lead Free Solders

The work is devoted to the study of shear strength of soldered joints fabricated by use of high-temperature solders of types Bi-11Ag, Au-20Sn, Sn-5Sb, Zn-4Al, Pb-5Sn, and Pb-10Sn. The shear strength was determined on metallic substrates made of Cu, Ni, and Ag. The strength of joints fabricated by use of flux and that of joints fabricated by use of ultrasonic activation without flux was compared. The obtained results have shown that in case of soldering by use of ultrasound (UT), higher shear strength of soldered joints was achieved with most solders. The highest shear strength by use of UT was achieved with an Au-20Sn joint fabricated on copper, namely up to 195 MPa. The lowest average values were achieved with Pb-based solders (Pb-5Sn and Pb-10Sn). The shear strength values of these solders used on Cu substrate varied from 24 to 27 MPa. DSC analysis was performed to determine the melting interval of lead-free solders.

scholarly journals Effects of Yttrium Addition on the Microstructure Evolution and Electrochemical Corrosion of SN-9zn Lead-Free Solders Al-Loy

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2549
Author(s):  
Wenchao Yang ◽  
Jun Mao ◽  
Yueyuan Ma ◽  
Shuyuan Yu ◽  
Hongping He ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Microstructure Evolution ◽  
Electrochemical Corrosion ◽  
Lead Free ◽  
Nacl Solution ◽  
Rich Phase ◽  
Yttrium Addition ◽  
Electrochemical Corrosion Behavior ◽  
Lead Free Solders ◽  
Addition Amount

Electrochemical corrosion behavior of ternary tin-zinc-yttrium (Sn-9Zn-xY) solder alloys were investigated in aerated 3.5 wt.% NaCl solution using potentiodynamic polarization techniques, and the microstructure evolution was obtained by scanning electron microscope (SEM). Eight different compositions of Sn-9Zn-xY (x = 0, 0.02, 0.04, 0.06, 0.08, 0.10, 0.20, and 0.30 wt.%) were compared by melting. The experimental results show that when the content of Y reached 0.06 wt.%, the grain size of Zn-rich phase became the smallest and the effect of grain refinement was the best, but there was no significant effect on the melting point. With the increases of Y content, the spreading ratio first increased and then decreased. When the content of Y was 0.06 wt.%, the Sn-9Zn-0.06Y solder alloy had the best wettability on the Cu substrate, which was increased by approximately 20% compared with Sn-9Zn. Besides, the electrochemical corrosion experimental shows that the Y can improve the corrosion resistance of Sn-9Zn system in 3.5 wt.% NaCl solution, and the corrosion resistance of the alloy is better when the amount of Y added is larger within 0.02–0.30 wt.%. Overall considering all performances, the optimal performance can be obtained when the addition amount of Y is 0.06.

scholarly journals Microstructure and Properties of TiAl-Based Alloys Melted in Graphite Crucible

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 669
Author(s):  
Wojciech Szkliniarz ◽  
Agnieszka Szkliniarz
Keyword(s):  
Coefficient Of Thermal Expansion ◽  
Graphite Crucible ◽  
Strength Properties ◽  
Operating Conditions ◽  
Vacuum Induction Furnace ◽  
Intermetallic Alloys ◽  
Plastic Properties ◽  
Similar Chemical ◽  
Crucible Furnace ◽  
Successive Generations

This paper presents the chemical and phase composition, microstructure, and selected properties both at room temperature and at the temperature corresponding to the expected operating conditions of three successive generations of TiAl-based alloys (Ti-47Al-2W-0.5Si, Ti-45Al-8Nb-0.5(B,C), and Ti-45Al-5Nb-2Cr-1Mo-0.5(B,C)-0.2Si) melted in a vacuum induction furnace with high-density isostatic pressed graphite crucibles. The obtained results of mechanical and physical properties of the produced alloys were compared to the properties of reference alloys with similar chemical composition and melted in a cold copper crucible furnace. The effect of increased carbon content in the produced alloys due to the degradation of the graphite crucible during melting is higher strength properties, lower plastic properties, higher coefficient of thermal expansion, and improved creep resistance. It was shown that the proposed technology could be successfully used in the production of different generation TiAl-based intermetallic alloys.

Sign in / Sign up

Export Citation Format

Share Document