Application of the Delta Transient Method to Multi-Rate Tests: A Method for Calculating Individual Layer Permeability and Skin in a Multilayered Reservoir using Production Logging Data

2017 ◽  
Author(s):  
Ciro S. Guimaraes ◽  
Mauricio S. C. Galvao
2020 ◽  
Vol 51 (5) ◽  
pp. 407-418
Author(s):  
Haiyan Lei ◽  
J. L. Han ◽  
J. H. Lu ◽  
Chuanshan Dai

Water ◽  
2021 ◽  
Vol 13 (3) ◽  
pp. 252
Author(s):  
Muhammad Shahinur Alam ◽  
David William Lamb ◽  
Nigel W. M. Warwick

Estimating transpiration as an individual component of canopy evapotranspiration using a theoretical approach is extremely useful as it eliminates the complexity involved in partitioning evapotranspiration. A model to predict transpiration based on radiation intercepted at various levels of canopy leaf area index (LAI) was developed in a controlled environment using a pasture species, tall fescue (Festuca arundinacea var. Demeter). The canopy was assumed to be a composite of two indistinct layers defined as sunlit and shaded; the proportion of which was calculated by utilizing a weighted model (W model). The radiation energy utilized by each layer was calculated from the PAR at the top of the canopy and the fraction of absorbed photosynthetically active radiation (fAPAR) corresponding to the LAI of the sunlit and shaded layers. A relationship between LAI and fAPAR was also established for this specific canopy to aid the calculation of energy interception. Canopy conductance was estimated from scaling up of stomatal conductance measured at the individual leaf level. Other environmental factors that drive transpiration were monitored accordingly for each individual layer. The Penman–Monteith and Jarvis evapotranspiration models were used as the basis to construct a modified transpiration model suitable for controlled environment conditions. Specially, constructed self-watering tubs were used to measure actual transpiration to validate the model output. The model provided good agreement of measured transpiration (actual transpiration = 0.96 × calculated transpiration, R2 = 0.98; p < 0.001) with the predicted values. This was particularly so at lower LAIs. Probable reasons for the discrepancy at higher LAI are explained. Both the predicted and experimental transpiration varied from 0.21 to 0.56 mm h−1 for the range of available LAIs. The physical proportion of the shaded layer exceeded that of the sunlit layer near LAI of 3.0, however, the contribution of the sunlit layer to the total transpiration remains higher throughout the entire growing season.


2010 ◽  
Vol 89-91 ◽  
pp. 503-508 ◽  
Author(s):  
J. Sheng ◽  
U. Welzel ◽  
Eric J. Mittemeijer

The stress evolution during diffusion annealing of Ni-Cu bilayers (individual layer thicknesses of 50 nm) was investigated employing ex-situ and in-situ X-ray diffraction measurements. Annealing at relatively low homologous temperatures (about 0.3 - 0.4 Tm) for durations up to about 100 hours results in considerable diffusional intermixing, as demonstrated by Auger-electron spectroscopy investigations (in combination with sputter-depth profiling). In addition to thermal stresses due to differences of the coefficients of thermal expansion of layers and substrate, tensile stress con-tributions in the sublayers arise during the diffusion anneals. The obtained stress data have been discussed in terms of possible mechanisms of stress generation. The influence of diffusion on stress development in the sublayers of the diffusion couple during heating and isothermal annealing was investigated by comparing stress changes in the bilayer system with corresponding results obtained under identical conditions for single layers of the components in the bilayer system. The specific residual stresses that emerge due to diffusion between the (sub)layers in the bilayer could thereby be identified.


1997 ◽  
Vol 481 ◽  
Author(s):  
R. R. Chromik ◽  
W. K. Neils ◽  
E. J. Cotts

ABSTRACTThe kinetics of the formation of Cu3Si in Cu/a-Si diffusion couples have been investigated by means of differential scanning calorimetry and x-ray diffraction. Multilayered composites of average stoichiometry Cu3Si were prepared by sputter deposition with individual layer thicknesses varying in different samples between 2 and 100 nm. We observed diffusion limited growth of Cu3 Si upon annealing these diffusion couples below 500 K. Reaction constants were measured for a temperature range of 455 to 495 K for thicknesses of growing Cu3Si between 2.6 and 80 nm. The temperature dependence of the reaction constant, k2, was characterized as k2 = k0 exp(− Ea/kbT) with activation energy, Ea = 1.0 eV/atom and pre-factor, k0 = 1.9×10−3 cm2/s.


Sign in / Sign up

Export Citation Format

Share Document