scholarly journals New methods for assessing brick resistance to freeze-thaw cycles

2021 ◽  
Vol 71 (343) ◽  
pp. e258
Author(s):  
I. Netinger-Grubeša ◽  
M. Benšić ◽  
M. Vračević
Keyword(s):  
Compressive Strength ◽  
Pore Radius ◽  
Pore System ◽  
Acceptable Risk ◽  
Water Desorption ◽  
Wrong Decision ◽  
Freeze Thaw ◽  
New Methods ◽  
Median Pore

The aim of this research is to analyse the reliability of the existing methods, and find new ones, for assessing brick resistance to freeze-thaw cycles. A series of bricks were tested against a range of properties; compressive strength ratios pre- to post-freezing and Maage’s factor, were calculated. Using a database created in this way, an analysis of existing classifiers was carried out and new ones were established based on which bricks could be classified into resistant and non-resistant to freeze-thaw cycles. The median pore radius, the ratio of compressive strengths pre- to post-freezing and the water desorption coefficient at 180-360 minutes proved to be good classifiers with a clearly specified cut-off for the distinction between resistant and non-resistant bricks with an acceptable risk of a wrong decision. The ratio of compressive strengths pre to post freezing and the water desorption coefficient at 180-360 minutes were described using the pore system in the brick.

scholarly journals Performances of Cement Mortar Incorporating Superabsorbent Polymer (SAP) Using Different Dosing Methods

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1619 ◽  
Author(s):  
Yawen Tan ◽  
Huaxin Chen ◽  
Zhendi Wang ◽  
Cheng Xue ◽  
Rui He
Keyword(s):  
Compressive Strength ◽  
Cement Mortar ◽  
Tap Water ◽  
Mass Loss Rate ◽  
Drying Shrinkage ◽  
Superabsorbent Polymer ◽  
Water Desorption ◽  
Cement Ratio ◽  
Freeze Thaw ◽  
Water To Cement Ratio

Modified cement mortar was prepared by incorporating a superabsorbent polymer (SAP) with two kinds of dosing state, dry powdery SAP and swelled SAP (where the SAP has been pre-wetted in tap water), respectively. The mechanical properties, drying shrinkage and freeze–thaw resistance of the mortars were compared and analyzed with the variation of SAP content and entrained water-to-cement ratios. Additionally, the effect of SAP on the microstructure of mortar was characterized by scanning electron microscopy (SEM). The results indicate that agglomerative accumulation is formed in the voids of mortar after water desorption from SAP and there are abundant hydration products, most of which are C-S-H gels, around the SAP voids. The incorporation of the powdery SAP increases the 28 d compressive strength of the mortars by about 10% to 50%, while for the incorporation of swelled SAP, the 28 d compressive strength of the mortar can be increased by about −26% to 6%. At a dosage of 0.1% SAP and an entrained water–cement ratio of 0.06, the powdery SAP and the swelled SAP can reduce the mortar shrinkage rate by about 32.2% and 14.5%, respectively. Both the incorporation of powdery and swelled SAP has a positive effect on the freeze–thaw resistance of cement mortar. In particular, for powdery SAP with an entrained water-to-cement ratio of 0.06, the mass loss rate after 300 cycles is still lower than 5%.

Optimization Research of Mix Proportion of Frost Resistance Construction of Concrete Based on the MATLAB Language

2014 ◽  
Vol 584-586 ◽  
pp. 1917-1921
Author(s):  
Jun Jie Zhang ◽  
Rui Hong Shao ◽  
Xiang Yi Meng
Keyword(s):  
Compressive Strength ◽  
Objective Function ◽  
Frost Resistance ◽  
Unit Volume ◽  
Influence Factors ◽  
Multi Objective Optimization ◽  
Cold Region ◽  
Freeze Thaw ◽  
Performance Indexes ◽  
Mix Proportion

Analyze the influence factors of mix proportion affecting concrete freeze-thaw damage. Use the five main performance indexes of the concrete, which are compressive strength, strength of extension, impermeability grade, and frost resistance grade and per unit volume cost concrete, as the objective function of multi-objective optimization equation. Invoke the fgoalattain function in the MATLAB Optimization Toolbox to solve. The optimized parameters of mix proportion of frost resistance construction of unit concrete in cold region are: concrete 1532.6kg, water 910kg, sand 5510.6kg, 5-20mm cobblestone 3747.2kg、20-40mm cobblestone 3658.6kg、40-80mm cobblestone 4733.5kg、80-150mm cobblestone 4738.1kg, and the dosage of water reducing agent is 7.3kg.

scholarly journals Strength Time–Varying and Freeze–Thaw Durability of Sustainable Pervious Concrete Pavement Material Containing Waste Fly Ash

2018 ◽  
Vol 11 (1) ◽  
pp. 176 ◽  
Author(s):  
Hanbing Liu ◽  
Guobao Luo ◽  
Longhui Wang ◽  
Yafeng Gong
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Pervious Concrete ◽  
Early Age ◽  
Pavement Materials ◽  
Freeze Thaw ◽  
Replacement Method ◽  
Porosity And Permeability ◽  
Volume Method

Pervious concretes, as sustainable pavement materials, have great advantages in addressing a number of environmental issues. Fly ash, as the industrial by-product waste, is the most commonly used as cement substitute in concrete. The objective of this paper is to study the effects of waste fly ash on properties of pervious concrete. Fly ash was used to replace cement with equivalent volume method at different levels (3%, 6%, 9%, and 12%). The control pervious concrete and fly ash modified pervious concrete were prepared in the laboratory. The porosity, permeability, compressive strength, flexural strength, and freeze–thaw resistance of all mixtures were tested. The results indicated that the addition of fly ash decreased the early-age (28 d) compressive strength and flexural strength, but the long-term (150 d) compressive strength and flexural strength of fly ash modified pervious concrete were higher than that of the early-age. The adverse effect of fly ash on freeze–thaw resistance of pervious concrete was observed when the fly ash was added. The porosity and permeability of all pervious concrete mixtures changed little with the content of fly ash due to the use of equal volume replacement method. Although fly ash is not positive to the properties of pervious concrete, it is still feasible to apply fly ash as a substitute for cement in pervious concrete.

Physical Properties of Building Blocks from Hemp Shives Aggregate and Cementitious Binder, Manufactured in the Expanded Clay (Vibro Pressing) Production Line

2017 ◽  
Vol 908 ◽  
pp. 118-122 ◽  
Author(s):  
Giedrius Balčiūnas ◽  
Viktor Kizinievič ◽  
Justinas Gargasas
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Compressive Strength ◽  
Physical Properties ◽  
Production Line ◽  
Scientific Literature ◽  
Building Blocks ◽  
Freeze Thaw ◽  
Cementitious Binder ◽  
Pressing Technology

Scientific literature mostly aims at investigation of composites with fibre hemp shives (FHS) aggregate and lime binder, although, such materials are characterised by pretty low mechanical properties. In order to obtain higher mechanical properties of a composite, it is appropriate to use cementitious binder. This work investigates physical properties of blocks from hemp shives aggregate and cementitious binder, manufactured in the expanded clay production line using vibro pressing technology. Following properties of the blocks are determined: freeze-thaw resistance, compressive strength, thermal conductivity and density. Thermal resistance according to EN ISO 6946 for the block with cavities is calculated as well. It is found that compressive strength of FHS-cement blocks may be up to 3.18 MPa when the density is of ~850 kg/m3 and thermal conductivity up to 0.135 W/(m∙K). It is found as well that the decrease of compressive strength is 8.7% after 25 freeze-thaw cycles.

scholarly journals Study on Strength Characteristics of Solidified Contaminated Soil under Freeze-Thaw Cycle Conditions

2018 ◽  
Vol 2018 ◽  
pp. 1-5 ◽  
Author(s):  
Qiang Wang ◽  
Jinyang Cui
Keyword(s):  
Electron Microscopy ◽  
Compressive Strength ◽  
Contaminated Soils ◽  
Unconfined Compressive Strength ◽  
Freeze Thaw ◽  
Thaw Cycle ◽  
Strength Tests ◽  
Freeze Thaw Cycle ◽  
Microcosmic Mechanism ◽  
Scanning Electron

Cement solidification/stabilization is a commonly used method for the remediation of contaminated soils. The stability characteristics of solidified/stabilized contaminated soils under freeze-thaw cycle are very important. A series of tests, which include unconfined compressive strength tests, freeze-thaw cycle tests, and scanning electron microscopy (SEM) tests, are performed to study the variation law of strength characteristics and microstructure. It aims at revealing the microcosmic mechanism of solidified/stabilized Pb2+ contaminated soils with cement under freeze-thaw cycle. The results show that the unconfined compressive strength of the contaminated soils significantly improved with the increase of the cement content. The unconfined compressive strength of stabilized contaminated soils first increases with the increase of times of freeze-thaw cycle, and after reaching the peak, it decreases with the increase of times of freeze-thaw cycle. The results of the scanning electron microscopy tests are consistent with those of the unconfined compressive strength tests. This paper also reveals the microcosmic mechanism of the changes in engineering of the stabilized contaminated soils under freeze-thaw cycle.

scholarly journals Degradation of Mechanical Behavior of Sandstone under Freeze-Thaw Conditions with Different Low Temperatures

2021 ◽  
Vol 11 (22) ◽  
pp. 10653
Author(s):  
Jingwei Gao ◽  
Chao Xu ◽  
Yan Xi ◽  
Lifeng Fan
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Mechanical Behavior ◽  
Energy Absorption ◽  
Uniaxial Compressive Strength ◽  
Dynamic Strength ◽  
Freezing Temperature ◽  
P Wave ◽  
Freeze Thaw ◽  
P Wave Velocity

This study investigated the effects of freezing temperature under freeze-thaw cycling conditions on the mechanical behavior of sandstone. First, the sandstone specimens were subjected to 10-time freeze-thaw cycling treatments at different freezing temperatures (−20, −40, −50, and −60 °C). Subsequently, a series of density, ultrasonic wave, and static and dynamic mechanical behavior tests were carried out. Finally, the effects of freezing temperature on the density, P-wave velocity, stress–strain curves, static and dynamic uniaxial compressive strength, static elastic modulus, and dynamic energy absorption of sandstone were discussed. The results show that the density slightly decreases as temperature decreases, approximately by 1.0% at −60 °C compared with that at 20 °C. The P-wave velocity, static and dynamic uniaxial compressive strength, static elastic modulus, and dynamic energy absorption obviously decrease. As freezing temperature decreases from 20 to −60 °C, the static uniaxial compressive strength, static elastic modulus, dynamic strength, and dynamic energy absorption of sandstone decrease by 16.8%, 21.2%, 30.8%, and 30.7%, respectively. The dynamic mechanical behavior is more sensitive to the freezing temperature during freeze-thawing cycling compared with the static mechanical behavior. In addition, a higher strain rate can induce a higher dynamic strength and energy absorption.

scholarly journals The effect of the pre-wetting of expanded clay aggregate on the freeze-thaw resistance of the expanded clay aggregate concrete

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Michał Piotr Musiał ◽  
Filip Grzymski ◽  
Tomasz Trapko
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Concrete Compressive Strength ◽  
Aggregate Concrete ◽  
Freeze Thaw ◽  
Concrete Mix Design ◽  
In Series ◽  
Resistance Criterion ◽  
Mixing Water ◽  
Nominal Amount

AbstractThis paper presents experimental research on expanded clay aggregate concrete. The aim of the investigations was to determine if the pre-wetting of expanded clay aggregate has an effect on the freeze-thaw durability of the expanded clay aggregate concrete. Five concrete series based on the same concrete mix design were made and tested. The degree of pre-wetting of the aggregate was varied: dry aggregate was used in the first series, aggregate with a moisture content of 10% was used in series IA and IB and aggregate with a moisture content of 25% was used in series IIA and IIB. Also the approach to the production process was varied: in series A the water contained in the aggregate was taken into account in the global water-cement ratio (consequently a reduced amount of water was added to the mix), whereas in series B the nominal amount of water was added to the mix (as in the case of dry aggregate). The freeze-thaw resistance criterion was based on the assessment of the decrease of compressive strength and increase in weight loss after exposure to freeze-thaw cycles. The expanded clay aggregate concrete's strength and mass decrements caused by freeze-thaw cycling were used as the measure of its freeze-thaw resistance. The investigations have shown that the pre-wetting of expanded clay aggregate has an effect on the freeze-thaw durability of the expanded clay aggregate concrete. The differences of concrete compressive strength decrease related to freeze-thaw durability may be 2 to 5 times greater when inadequate method of calculating mixing water for concrete is used.

Performance Deterioration of High Strength Concrete under Mixed Erosion and Freeze-Thaw Cycling

2010 ◽  
Vol 163-167 ◽  
pp. 1655-1660
Author(s):  
Jian Zhang ◽  
Bo Diao ◽  
Xiao Ning Zheng ◽  
Yan Dong Li
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Mass Loss ◽  
Modulus Of Elasticity ◽  
Dynamic Modulus ◽  
High Strength Concrete ◽  
High Strength ◽  
Freeze Thaw ◽  
Strength Concrete ◽  
Dynamic Modulus Of Elasticity

The mechanical properties of high strength concrete(HSC) were experimentally investigated under mixed erosion and freeze-thaw cycling according to ASTM C666(Procedure B), the erosion solution was mixed by weight of 3% sodium chloride and 5% sodium sulfate. The mass loss, relative dynamic modulus of elasticity, compressive strength, elastic modulus and other relative data were measured. The results showed that with the increasing number of freeze-thaw cycles, the surface scaled more seriously; the mass loss, compressive strength and elastic modulus continued to decrease; the relative dynamic modulus of elasticity increased slightly in the first 225 freeze-thaw cycles, then decreased in the following 75 cycles; the corresponding strain to peak stress decreased with the increase of freeze-thaw cycles. After 200 cycles, the rate of deterioration of concrete accelerated obviously.

Iron (III) Oxide within Mesoporous MCM-48 Silica Phases: Synthesis and Characterization

1998 ◽  
Vol 547 ◽  
Author(s):  
R. Köhna ◽  
G. Bouffaud ◽  
O. Richard ◽  
G. van Tendeloo ◽  
M. Fröba
Keyword(s):  
Pore Radius ◽  
Bet Surface Area ◽  
Synthesis And Characterization ◽  
Pore System ◽  
Wet Impregnation ◽  
X Ray ◽  
Inner Surface ◽  
Multiple Cycles ◽  
Silica Phases ◽  
X Ray Absorption

AbstractUsing multiple cycles of wet impregnation, drying and calcination procedures it was possible to form haematite nanoparticles within the pore system of mesoporous MCM-48 silica phase. A decoration/coating of the inner surface of the silica walls was indicated by a reduction of the BET surface area, the pore radius as well as HRTEM and EDX investigations. Existence of small, slightly disordered iron (III) oxide nanoparticles was proved by X-ray absorption spectroscopic measurements.

Sign in / Sign up

Export Citation Format

Share Document