scholarly journals Local Buckling Influence on the Moment Redistribution Coefficient for Composite Continuous Beams of Bridges

2010 ◽  
Vol 5 (4) ◽  
pp. 207-217 ◽  
Author(s):  
Samy Guezouli ◽  
Mohammed Hjiaj ◽  
Nguyen Quang Huy
Keyword(s):  
Local Buckling ◽  
Moment Redistribution ◽  
Continuous Beams ◽  
The Moment

Post-Local-Buckling Behavior of Continuous Beams

1974 ◽  
Vol 100 (6) ◽  
pp. 1169-1187
Author(s):  
Shien T. Wang ◽  
Sheng S. Yeh
Keyword(s):  
Local Buckling ◽  
Continuous Beams ◽  
Buckling Behavior

scholarly journals A Matrix Formulation for the Moment Distribution Method Applied to Continuous Beams

2011 ◽  
Vol 2011 ◽  
pp. 1-9 ◽  
Author(s):  
Arlindo Pires Lopes ◽  
Adriana Alencar Santos ◽  
Rogério Coelho Lopes
Keyword(s):  
Structural Analysis ◽  
Algebraic Equations ◽  
Displacement Method ◽  
Matrix Formulation ◽  
Distribution Method ◽  
Continuous Beams ◽  
Moment Distribution ◽  
Moment Distribution Method ◽  
Carry Over ◽  
The Moment

The Moment Distribution Method is a quite powerful hand method of structural analysis, in which the solution is obtained iteratively without even formulating the equations for the unknowns. It was formulated by Professor Cross in an era where computer facilities were not available to solve frame problems that normally require the solution of simultaneous algebraic equations. Its relevance today, in the era of personal computers, is in its insight on how a structure reacts to applied loads by rotating its nodes and thus distributing the loads in the form of member-end moments. Such an insight is the foundation of the modern displacement method. This work has a main objective to present an exact solution for the Moment Distribution Method through a matrix formulation using only one equation. The initial moments at the ends of the members and the distribution and carry-over factors are calculated from the elementary procedures of structural analysis. Four continuous beams are investigated to illustrate the applicability and accuracy of the proposed formulation. The use of a matrix formulation yields excellent results when compared with those in the literature or with a commercial structural program.

scholarly journals Experimental Research of Continuous Concrete Beams with GFRP Reinforcement

2018 ◽  
Vol 2018 ◽  
pp. 1-16 ◽  
Author(s):  
Nikola Baša ◽  
Mladen Ulićević ◽  
Radomir Zejak
Keyword(s):  
Experimental Research ◽  
American Concrete Institute ◽  
Rc Structures ◽  
Moment Redistribution ◽  
Continuous Beams ◽  
Load Carrying ◽  
Current Design ◽  
Frp Reinforcement ◽  
Internal Forces ◽  
Gfrp Reinforcement

Continuous beams are often used within RC structures, which are exposed to aggressive environmental impact. The use of the fiber-reinforced polymer (FRP) reinforcement in these objects and environments has a big significance, taking into account tendency of steel reinforcement to corrode. The main aim of these research studies is to estimate ability of continuous beams with glass FRP (GFRP) reinforcement to redistribute internal forces, as a certain way of ductility and desirable behaviour of RC structures. This paper gives the results of experimental research of seven continuous beams, over two spans of 1850 mm length, cross-section of 150 × 250 mm, that are imposed to concentrated forces in the middle of spans until failure. Six beams were reinforced with different longitudinal GFRP and same transverse GFRP reinforcements, and one steel-reinforced beam was adopted as a control beam. The main varied parameters represent the type of GFRP reinforcement and ratio of longitudinal reinforcement at the midspan and at the middle support, i.e., design moment redistribution. The results of the research have shown that moment redistribution in continuous beams of GFRP reinforcement is possible, without decreasing the load-carrying capacity, compared to elastic analysis. The test results have also been compared to current code provisions, and they have shown that the American Concrete Institute (ACI) 440.1R-15 well predicted the failure load for continuous beams with GFRP reinforcement. On the contrary, current design codes underestimate deflection of continuous beams with GFRP reinforcement, especially for higher load levels. Consequently, a modified model for calculation of deflection is proposed.

scholarly journals IV. On the practical solution of the most general problems in continuous beams

1879 ◽  
Vol 29 (196-199) ◽  
pp. 493-505
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
General Problem ◽  
Bending Moment ◽  
Moment Of Inertia ◽  
Shearing Stress ◽  
Practical Solution ◽  
Continuous Beams ◽  
The Moment

1. It is not necessary to enter into the question of the advisability of employing continuous girders in bridges with spans of less than 200 feet, but it is generally conceded that the increased economy due to the employment of continuous girders in longer spans more than counterbalances the well-known practical objections to continuity. Hence the practical solution of the general problem—given the conditions at the ends of a continuous girder, the spans, the moment of inertia of all cross sections, and the loading, to find the bending moment and shearing stress in every cross-section, is not unworthy of our attention.

Sign in / Sign up

Export Citation Format

Share Document