scholarly journals PERHITUNGAN TEGANGAN POROS MODEL PROPELLER PADA UJI SELF PROPULSION MODEL KAPAL

2019 ◽  
Vol 9 (2) ◽  
pp. 321
Author(s):  
Suyadi Suyadi ◽  
Ahmad Syafiul
Keyword(s):  
Maximum Stress ◽  
Test Model ◽  
Main Function ◽  
Routine Work ◽  
Steel Aisi ◽  
Technical Study ◽  
Self Test ◽  
Work Done ◽  
Stainless Steel Aisi ◽  
Test Process

Shaft and propeller is the main function of the implementation of model self-test model self-declaration is a routine work done in BTH - BPPT. Axis serves to move or forward power from transmission to propeller so that the propeller can rotate. The shaft is made of steel pipe or stainless steel (AISI 1020) which has resistance to twist or bending force. Therefore a technical study of the magnitude of torsion and bending stress is necessary for predicting the life of the shaft. To obtain the shaft life is calculated in the propulsion test process where the variable chosen in the propulsion test process is the velocity of the vessel model which is the parameters that influence the force, torque and tension changes. The results of this study indicate that for the model speed of 1.529 m/s obtained the maximum stress 31.75 Mpa / 4.63 Ksi axis operates in normal conditions while the allowable voltage allowable 294,74 Mpa / 42,75 Ksi

scholarly journals Stainless steel corrosion in instrumentation pipe

2019 ◽  
Vol 14 (40) ◽  
pp. 31-40
Author(s):  
Jean Victal do Nascimento ◽  
Rafael Adão de Carvalho ◽  
Davi Pereira Garcia ◽  
Rômulo Maziero ◽  
Edelize Angelica Gomes ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Chemical Composition ◽  
Austenitic Stainless Steel ◽  
Stainless Steels ◽  
Chloride Ions ◽  
Main Function ◽  
Marine Atmosphere ◽  
Steel Aisi ◽  
Aisi 316 ◽  
Stainless Steel Aisi

Corrosion, being a destructive process, causes damage in almost all industrial sectors. In this way, it is harmful both from an economic, social and, especially, safety point of view, as it can cause failures in critical equipment and components of an industrial process. At this point, stainless steels are considered the most corrosion resistant metals. The resistance depends on the chemical composition and microstructure, factors that directly influence the passivation of these materials. The resistance is proportionally related to the addition of chromium (Cr) to the mixture, as well as other alloying elements, among which is the molybdenum (Mo), whose main function is to maximize corrosion resistance in the marine atmosphere, as in case of austenitic stainless steel AISI 316 which presents in the chemical composition a percentage of the element Mo. Austenitic stainless steels are applied in instrumentation systems in tubing for reliability in severe atmospheres in accordance with ASTM A269 which establishes the materials applicable to this function. Thus, the present work presents, through a review and case study, Pitting Corrosion of tubings of austenitic stainless steel AISI 316 in the presence of chloride ions (Cl-) coming from the marine atmosphere. The results show that there is no change in the longitudinal and transverse structure for all analyzed tubes, showing a homogeneous austenitic structure, free of intergranular precipitations.

scholarly journals Frais chisel Shaft Strength Calculation on the Model in the Laboratory Hydrodynamic

2018 ◽  
Vol 2 (2) ◽  
pp. 87
Author(s):  
Suyadi Suyadi ◽  
Hardi Zen
Keyword(s):  
Service Life ◽  
Engine Speed ◽  
Propeller Shaft ◽  
Machining Processes ◽  
Main Work ◽  
Routine Work ◽  
Milling Machines ◽  
Technical Study ◽  
Work Done ◽  
Ship Propeller

A process process in the manufacture of milling machines Keyway (slot) propeller shaft models - ship   propeller is routine work done in  BTH-BPPT. The main work in this process requires the use of a standard cutting blade milling (Hight Speed Steel), therefore the technical study on the magnitude of cutting force is needed in predicting the service life of the milling blade. To get the service life of the chisel eye analysis in the process of cutting with a knife cut milling standard (HSS) where the variables selected in this machining processes such as engine speed is very influential parameter to change the style, torque and strain. The results showed that for the process sharpener at rpm 400 rpm and 500 rpm eyes chisel operating under normal conditions, while at rpm 785 rpm chisel eye operating at extreme conditions in which the generated strain of 39.6 Ksi and lifespan chisel 138 operational days 4,5 frais chisel or a calendar month. 

scholarly journals Stainless steel corrosion in instrumentation pipe

2019 ◽  
Vol 14 (40) ◽  
pp. 31-40
Author(s):  
Jean Victal do Nascimento ◽  
Rafael Adão de Carvalho ◽  
Davi Pereira Garcia ◽  
Rômulo Maziero ◽  
Edelize Angelica Gomes ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Chemical Composition ◽  
Austenitic Stainless Steel ◽  
Stainless Steels ◽  
Chloride Ions ◽  
Main Function ◽  
Marine Atmosphere ◽  
Steel Aisi ◽  
Aisi 316 ◽  
Stainless Steel Aisi

Corrosion, being a destructive process, causes damage in almost all industrial sectors. In this way, it is harmful both from an economic, social and, especially, safety point of view, as it can cause failures in critical equipment and components of an industrial process. At this point, stainless steels are considered the most corrosion resistant metals. The resistance depends on the chemical composition and microstructure, factors that directly influence the passivation of these materials. The resistance is proportionally related to the addition of chromium (Cr) to the mixture, as well as other alloying elements, among which is the molybdenum (Mo), whose main function is to maximize corrosion resistance in the marine atmosphere, as in case of austenitic stainless steel AISI 316 which presents in the chemical composition a percentage of the element Mo. Austenitic stainless steels are applied in instrumentation systems in tubing for reliability in severe atmospheres in accordance with ASTM A269 which establishes the materials applicable to this function. Thus, the present work presents, through a review and case study, Pitting Corrosion of tubings of austenitic stainless steel AISI 316 in the presence of chloride ions (Cl-) coming from the marine atmosphere. The results show that there is no change in the longitudinal and transverse structure for all analyzed tubes, showing a homogeneous austenitic structure, free of intergranular precipitations.

Synthesis and characterization of TiN / Ti / AISI 410 coatings

2018 ◽  
Vol 2 (1) ◽  
pp. 7
Author(s):  
S Chirino ◽  
Jaime Diaz ◽  
N Monteblanco ◽  
E Valderrama
Keyword(s):  
Synthesis And Characterization ◽  
Photoemission Spectroscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Columnar Grains ◽  
Tin Thin Films ◽  
Steel Aisi ◽  
Interacting Surfaces ◽  
Stainless Steel Aisi

The synthesis and characterization of Ti and TiN thin films of different thicknesses was carried out on a martensitic stainless steel AISI 410 substrate used for tool manufacturing. The mechanical parameters between the interacting surfaces such as thickness, adhesion and hardness were measured. By means of the scanning electron microscope (SEM) the superficial morphology of the Ti/TiN interface was observed, finding that the growth was of columnar grains and by means of EDAX the existence of titanium was verified.  Using X-ray diffraction (XRD) it was possible to observe the presence of residual stresses (~ -3.1 GPa) due to the different crystalline phases in the coating. Under X-ray photoemission spectroscopy (XPS) it was possible to observe the molecular chemical composition of the coating surface, being Ti-N, Ti-N-O and Ti-O the predominant ones.

AL TECH MIAMI

Alloy Digest ◽  
1983 ◽  
Vol 32 (11) ◽  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Heat Treating ◽  
Good Resistance ◽  
Aisi Type ◽  
Steel Aisi ◽  
Resistance To Wear ◽  
Specialty Steel ◽  
Stainless Steel Aisi ◽  
Plastic Mold

Abstract AL TECH MIAMI is both a hardenable stainless steel (AISI Type 420) and a tool steel for making molds for plastic. A major requirement for plastic mold steel is corrosion resistance. Certain plastics, such as poly-vinyl chlorides, are very corrosive and stored molds often rust from sweating water lines and/or humid environments. AL TECH MIAMI has good resistance to wear. It is melted and AOD refined to assure the mold-maker of cleanliness and freedom from internal imperfections. It provides exceptionally good polishability for lens-quality molds. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, and machining. Filing Code: SS-435. Producer or source: AL Tech Specialty Steel Corporation.

scholarly journals Influence of Activated Fluxes on the Bead Shape of A-TIG Welds on Carbon and Low-Alloy Steels in Comparison with Stainless Steel AISI 304L

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 530
Author(s):  
Jerzy Niagaj
Keyword(s):  
Stainless Steel ◽  
Penetration Depth ◽  
High Strength ◽  
Tig Welding ◽  
Low Alloy Steels ◽  
Aisi 304L ◽  
A Tig Welding ◽  
Alloy Steels ◽  
Steel Aisi ◽  
Stainless Steel Aisi

The article presents results of comparative A-TIG welding tests involving selected unalloyed and fine-grained steels, as well as high-strength steel WELDOX 1300 and austenitic stainless steel AISI 304L. The tests involved the use of single ingredient activated fluxes (Cr2O3, TiO2, SiO2, Fe2O3, NaF, and AlF3). In cases of carbon and low-alloy steels, the tests revealed that the greatest increase in penetration depth was observed in the steels which had been well deoxidized and purified during their production in steelworks. The tests revealed that among the activated fluxes, the TiO2 and SiO2 oxides always led to an increase in penetration depth during A-TIG welding, regardless of the type and grade of steel. The degree of the aforesaid increase was restricted within the range of 30% to more than 200%.

The Design and Realization of a Network Test Questions System

2011 ◽  
Vol 403-408 ◽  
pp. 1364-1367
Author(s):  
Ren Xiang Shao ◽  
Li Wan
Keyword(s):  
Linear Algebra ◽  
Test Model ◽  
Test Question ◽  
Adaptive Network ◽  
Self Test ◽  
Self Adaptive

The article sets up a self-adaptive network test model and introduces a system for the course “Linear Algebra”. The system can present different problems on the basis of tester level and the process of answering question. The system may reduce the amount of test question, shorten the time of the test and estimate more accurately the level of the tester relative to tradition test. The paper has certain direction meaning for tester self-test and computer assistant test.

Phase Studies in WC-Stainless Steel AISI 347 Hardmetal System with Graphite Addition

2014 ◽  
Vol 1024 ◽  
pp. 239-242
Author(s):  
Zuhailawati Hussain ◽  
Emee Marina Salleh ◽  
Tran Bao Trung ◽  
Zainal Arifin Ahmad
Keyword(s):  
Stainless Steel ◽  
Powder Mixture ◽  
Milled Powder ◽  
Graphite Powder ◽  
Planetary Mill ◽  
Argon Atmosphere ◽  
Maximum Hardness ◽  
Steel Container ◽  
Steel Aisi ◽  
Stainless Steel Aisi

In this study, WC-stainless steel AISI 347 hardmetal system was produced to replace WC-Co hardmetal which uses the expensive, toxic and depleted resource Co. WC, stainless steel AISI 347 and graphite powder mixture were milled in a planetary mill under argon atmosphere using a stainless steel container and balls. Carbon was added in amounts ranging from 0 wt% until 4 wt% into the composition to avoid unwanted η (Fe3W3C) phase. As-milled powder was compacted at 300 MPa and sintered in a tube furnace at 1350°C. ɳ phase was detected in compositions with 0 and 1 wt% C addition. For 2 wt% C addition, no η (Fe3W3C) phase formation was identified. However, the η phase was detected for compositions containing 3 and 4 wt% C. Maximum hardness was achieved due to the absence of η phase.

Sign in / Sign up

Export Citation Format

Share Document