Specification for wrought aluminium and aluminium alloys for general engineering purposes - forgings (including hot pressing, hot stampings, drop stampings and drop forgings)

1951 ◽  
Keyword(s):  
Hot Pressing ◽  
Aluminium Alloys

“Cavity” formation in superplastically deformed aluminium alloys

1990 ◽  
Vol 48 (4) ◽  
pp. 958-959
Author(s):  
A. Cziráki ◽  
E. Ková-csetényi ◽  
T. Torma ◽  
T. Turmezey
Keyword(s):  
Grain Boundaries ◽  
Aluminium Alloys ◽  
Superplastic Deformation ◽  
Volume Fraction ◽  
Superplastic Forming ◽  
Polished Surface ◽  
Cavity Formation ◽  
Stress Concentrations ◽  
Electron Microscopic ◽  
Commercial Aluminium

It is known that the formation of cavities during superplastic deformation can be correlated with the development of stress concentrations at irregularities along grain boundaries such as particles, ledges and triple points. In commercial aluminium alloys Al-Fe-Si particles or other coarse constituents may play an important role in cavity formation.Cavity formation during superplastic deformation was studied by optical metallography and transmission scanning electron microscopic investigations on Al-Mg-Si and Al-Mg-Mn alloys. The structure of particles was characterized by selected area diffraction and X-ray micro analysis. The volume fraction of “voids” was determined on mechanically polished surface.It was found by electron microscopy that strongly deformed regions are formed during superplastic forming at grain boundaries and around coarse particles.According to electron diffraction measurements these areas consist of small micro crystallized regions. See Fig.l.Comparing the volume fraction and morphology of cavities found by optical microscopy a good correlation was established between that of micro crystalline regions.

Microstructure of mechanically alloyed and hot-pressed Al5CuZr2

1990 ◽  
Vol 48 (4) ◽  
pp. 970-971
Author(s):  
T. E. Mitchell ◽  
P. B. Desch ◽  
R. B. Schwarz
Keyword(s):  
Mechanical Alloying ◽  
Vickers Hardness ◽  
Hot Pressing ◽  
Rapid Quenching ◽  
Hardened Steel ◽  
Alloyed Powder ◽  
Ion Milling ◽  
Mechanical Grinding ◽  
Mechanically Alloyed ◽  
Steel Container

Al3Zr has the highest melting temperature (1580°C) among the tri-aluminide intermetal1ics. When prepared by casting, Al3Zr forms in the tetragonal DO23 structure but by rapid quenching or by mechanical alloying (MA) it can also be prepared in the metastable cubic L12 structure. The L12 structure can be stabilized to at least 1300°C by the addition of copper and other elements. We report a TEM study of the microstructure of bulk Al5CuZr2 prepared by hot pressing mechanically alloyed powder.MA was performed in a Spex 800 mixer using a hardened steel container and balls and adding hexane as a surfactant. Between 1.4 and 2.4 wt.% of the hexane decomposed during MA and was incorporated into the alloy. The mechanically alloyed powders were degassed in vacuum at 900°C. They were compacted in a ram press at 900°C into fully dense samples having Vickers hardness of 1025. TEM specimens were prepared by mechanical grinding followed by ion milling at 120 K. TEM was performed on a Philips CM30 at 300kV.

Effect of hot pressing on the modulated structure of Zr0.98Sn0.02TiO4

1998 ◽  
Vol 77 (4) ◽  
pp. 1033-1037 ◽  
Author(s):  
Y. Park, S. A. Song H., G. Kim
Keyword(s):  
Hot Pressing ◽  
Modulated Structure

PRECISION PRESSURE WELDING OF ALUMINIUM ALLOYS

2017 ◽  
pp. 67-76 ◽  
Author(s):  
Oleg Novomlynets ◽  
◽  
Serhii Oleksiienko ◽  
Svitlana Yushchenko ◽  
Evgen Polovetskiy ◽  
...  
Keyword(s):  
Aluminium Alloys ◽  
Pressure Welding
Sign in / Sign up

Export Citation Format

Share Document