Polyethylene (PE) pipes and fittings � Determination of the tensile strength and failure mode of test pieces from a butt-fused joint

2020 ◽  
Keyword(s):  
Tensile Strength ◽  
Failure Mode ◽  
Test Pieces

A Short Note on the Tensile Testing of Rubber

1932 ◽  
Vol 5 (3) ◽  
pp. 351-355 ◽  
Author(s):  
M. Jones
Keyword(s):  
Tensile Strength ◽  
Tensile Testing ◽  
Short Note ◽  
American Chemical Society ◽  
Chemical Society ◽  
Ring Test ◽  
Stress Strain ◽  
Test Pieces ◽  
The One

Abstract The evaluation of rubber has centered largely around stress-strain phenomena, and the property of tensile strength is probably the one which has the most general application throughout the industry. Rubber exhibits stress-strain properties quite different from the majority of substances, and peculiar difficulties are introduced during the determination of tensile strength. Although tentative standards have recently been issued by the American Chemical Society, there is no evidence that these are being strictly adhered to, and there is still need for a more rigid standardization of tensile-testing methods. There are essentially two methods of tensile-testing: (1) Using dumb-bell test-pieces with a Bureau of Standards machine, or a Scott type of machine; and (2) Using ring test-pieces with a Schopper type of machine. It is generally supposed that higher tensile results are obtained by the former method. Recently, occasion has occurred to make a comparison between both types and to study the effect of certain factors upon each method.

MEEHANITE GB300

Alloy Digest ◽  
2020 ◽  
Vol 69 (11) ◽  
Keyword(s):  
Thermal Conductivity ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Gray Cast Iron ◽  
High Strength ◽  
Heat Treating ◽  
Spheroidal Graphite ◽  
Cast Irons ◽  
Test Pieces ◽  
Temperature Performance

Abstract Meehanite GB300 is a pearlitic gray cast iron that has a minimum tensile strength of 300 MPa (44 ksi), when determined on test pieces machined from separately cast, 30 mm (1.2 in.) diameter test bars. This grade exhibits high strength while still maintaining good thermal conductivity and good machinability. It is generally used for applications where the thermal conductivity requirements preclude the use of other higher-strength materials, such as spheroidal graphite cast irons, which have inferior thermal properties. This datasheet provides information on physical properties, hardness, tensile properties, and compressive strength as well as fatigue. It also includes information on low and high temperature performance as well as heat treating, machining, and joining. Filing Code: CI-75. Producer or source: Meehanite Metal Corporation.

ISO 185/JL/225

Alloy Digest ◽  
2020 ◽  
Vol 69 (9) ◽  
Keyword(s):  
Tensile Strength ◽  
Cast Iron ◽  
Gray Cast Iron ◽  
Heat Treating ◽  
International Organization ◽  
Gray Cast ◽  
Damping Capacity ◽  
Lower Strength ◽  
Test Pieces ◽  
Lower Carbon

Abstract ISO 185/JL/225 is an intermediate-tensile-strength gray cast iron that has a predominantly pearlitic matrix, and a tensile strength of 225–325 MPa (33-47 ksi), when determined on test pieces machined from separately cast, 30 mm (1.2 in.) diameter test bars. Compared with the lower strength gray cast iron grades, ISO 185/JL/225 contains lower carbon and silicon contents, while still maintaining excellent thermal conductivity, damping capacity, and machinability. This datasheet provides information on composition, physical properties, tensile properties, and compressive strength as well as fatigue. It also includes information on heat treating. Filing Code: CI-73. Producer or source: International Organization for Standardization (ISO).

Sign in / Sign up

Export Citation Format

Share Document