Plastics. Compression moulding test specimens of thermoplastic materials

2003 ◽  
Keyword(s):  
Compression Moulding

Effect of Cobalt Stearate and Vegetable Oil on Uv and Biodegradation of Linear Low-Density Poly(Ethylene)-Poly(Vinyl Alcohol) Blends

2011 ◽  
Vol 2 (4) ◽  
pp. 131-148 ◽  
Author(s):  
Francis Vidya ◽  
Subin S. Raghul ◽  
Sarita G Bhat ◽  
Eby Thomas Thachil
Keyword(s):  
Vegetable Oil ◽  
Vinyl Alcohol ◽  
Water Soluble ◽  
Poly Vinyl Alcohol ◽  
Low Density ◽  
Compression Moulding ◽  
Melt Mixing ◽  
Degradation Behaviour ◽  
Moulding Process ◽  
Poly Ethylene

The main objective of this study was to enhance the rate of UV and biodegradation of polyethylene by incorporating biodegradable materials and prooxidants. Prooxidants such as transition metal complexes are capable of initiating photooxidation and polymer chain cleavage, rendering the product more susceptible to biodegradation. In this work, the effect of (1) a metallic photoinitiator, cobalt stearate, and (2) different combinations of cobalt stearate and vegetable oil on the photooxidative degradation of linear low-density poly(ethylene)-poly(vinyl alcohol) (LLDPE/PVA) blend films has been investigated. For this, film-grade LLDPE was blended with different proportions of PVA. PVA is widely used in the industrial field, and recently it has attracted increasing attention as a water-soluble biodegradable polymer. Cobalt stearate and vegetable oil were added to the blends as prooxidants. The blends were prepared by melt mixing in a Thermo HAAKE Polylab system. Thin films containing these additives were prepared by a subsequent compression moulding process. The effect of UV exposure on LLDPE/PVA films in the presence as well as absence of these additives was investigated. Tensile properties, FTIR spectra, and scanning electron microscopy (SEM) were employed to investigate the degradation behaviour. It was found

scholarly journals Functional Properties and Molecular Degradation of Schizostachyum Brachycladum Bamboo Cellulose Nanofibre in PLA-Chitosan Bionanocomposites

Molecules ◽  
2021 ◽  
Vol 26 (7) ◽  
pp. 2008
Author(s):  
Samsul Rizal ◽  
N. I. Saharudin ◽  
N. G. Olaiya ◽  
H. P. S. Abdul Khalil ◽  
M. K. Mohamad Haafiz ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Moisture Content ◽  
Polymeric Materials ◽  
Particle Size Analysis ◽  
Size Analysis ◽  
Thickness Swelling ◽  
Compression Moulding ◽  
Ft Ir ◽  
Degradation Properties

The degradation and mechanical properties of potential polymeric materials used for green manufacturing are significant determinants. In this study, cellulose nanofibre was prepared from Schizostachyum brachycladum bamboo and used as reinforcement in the PLA/chitosan matrix using melt extrusion and compression moulding method. The cellulose nanofibre(CNF) was isolated using supercritical carbon dioxide and high-pressure homogenisation. The isolated CNF was characterised with transmission electron microscopy (TEM), FT-IR, zeta potential and particle size analysis. The mechanical, physical, and degradation properties of the resulting biocomposite were studied with moisture content, density, thickness swelling, tensile, flexural, scanning electron microscopy, thermogravimetry, and biodegradability analysis. The TEM, FT-IR, and particle size results showed successful isolation of cellulose nanofibre using this method. The result showed that the physical, mechanical, and degradation properties of PLA/chitosan/CNF biocomposite were significantly enhanced with cellulose nanofibre. The density, thickness swelling, and moisture content increased with the addition of CNF. Also, tensile strength and modulus; flexural strength and modulus increased; while the elongation reduced. The carbon residue from the thermal degradation and the glass transition temperature of the PLA/chitosan/CNF biocomposite was observed to increase with the addition of CNF. The result showed that the biocomposite has potential for green and sustainable industrial application.

The effects of adding carbon nanotubes to the mechanical and tribological properties of a carbon fibre reinforced polyether ether ketone composite

2009 ◽  
Vol 223 (11) ◽  
pp. 2501-2507 ◽  
Author(s):  
J Li ◽  
L Q Zhang
Keyword(s):  
Carbon Nanotubes ◽  
Wear Resistance ◽  
Carbon Fibre ◽  
Vinyl Ester ◽  
High Wear Resistance ◽  
Compression Moulding ◽  
Mechanical And Tribological Properties ◽  
Polyether Ether Ketone ◽  
Carbon Nano Tubes ◽  
Ether Ketone

The main objective of this article is to develop a high wear resistance carbon fibre (CF)-reinforced polyether ether ketone composite with the addition of multi-wall carbon nano-tubes (MWCNT). These compounds were well mixed in a Haake batch mixer and compounded polymers were fabricated into sheets of known thickness by compression moulding. Samples were tested for wear resistance with respect to different concentrations of fillers. Wear resistance of a composite with 20 wt% of CF increases when MWCNT was introduced. The worn surface features have been examined using a scanning electron microscope (SEM). Photomicrographs of the worn surfaces revealed higher wear resistance with the addition of carbon nanotubes. Also better interfacial adhesion between carbon and vinyl ester in a carbon-reinforced vinyl ester composite was observed.

Compression Moulding of Rubber Powder from Exhausted Tyres

2012 ◽  
Vol 51 (4) ◽  
pp. 340-344 ◽  
Author(s):  
Carmine Lucignano ◽  
Alessandro Gugliemotti ◽  
Fabrizio Quadrini
Keyword(s):  
Compression Moulding ◽  
Rubber Powder

Imide Oligomers Containing Pendent and Terminal Phenylethynyl Groups—II

1998 ◽  
Vol 10 (3) ◽  
pp. 273-283 ◽  
Author(s):  
J W Connell ◽  
J G Smith ◽  
P M Hergenrother
Keyword(s):  
Molecular Weight ◽  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Average Molecular Weight ◽  
Adhesive Tape ◽  
High Glass Transition Temperature ◽  
Compressive Properties ◽  
Compression Moulding ◽  
Imide Oligomers

As part of a programme to develop high-performance/high-temperature structural resins for aeronautical applications, imide oligomers containing pendent and terminal phenylethynyl groups were prepared, characterized and the cured resins evaluated as composite matrices. The oligomers were prepared at a calculated number-average molecular weight of 5000 g mol−1 and contained 15–20 mol% pendent phenylethynyl groups. In previous work, an oligomer containing pendent and terminal phenylethynyl groups exhibited a high glass transition temperature (∼313 °C), and laminates therefrom exhibited high compressive properties, but processability, fracture toughness, microcrack resistance and damage tolerance were less than desired. In an attempt to improve these deficiencies, modifications in the oligomeric backbone involving the incorporation of 1,3-bis(3-aminophenoxy)benzene were investigated as a means of improving processability and toughness without detracting from the high glass transition temperature and high compressive properties. The amide acid oligomeric solutions were prepared in N-methyl-2-pyrrolidinone and were subsequently processed into imide powder, thin films, adhesive tape and carbon fibre prepreg. Neat resin plaques were fabricated from imide powder by compression moulding. The maximum processing pressure was 1.4 MPa and the cure temperature ranged from 350 to 371 °C for 1 h for the mouldings, adhesives, films and composites. The properties of the 1,3-bis(3-aminophenoxy)benzene modified cured imide oligomers containing pendent and terminal phenylethynyl groups are compared with those of previously prepared oligomers containing pendent and terminal phenylethynyl groups of similar composition and molecular weight.

scholarly journals Carbon Fiber Composites of Pure Polypropylene and Maleated Polypropylene Blends Obtained from Injection and Compression Moulding

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
D. Pérez-Rocha ◽  
A. B. Morales-Cepeda ◽  
F. Navarro-Pardo ◽  
T. Lozano-Ramírez ◽  
P. G. LaFleur
Keyword(s):  
Mechanical Performance ◽  
Impact Resistance ◽  
Structural Features ◽  
Strength Properties ◽  
Favourable Effect ◽  
Carbon Fiber Composites ◽  
Compression Moulding ◽  
Scanning Calorimetry ◽  
Noticeable Effect ◽  
Maleated Polypropylene

A comparative study of the mechanical performance of PP and PP/PP-g-MAH blends reinforced with carbon fibre (CF) obtained by two different moulding techniques is presented. Three filler contents were used for fabricating the composites: 1, 3, and 5 pph (parts per hundred). The crystallisation behaviour of the composites was studied by differential scanning calorimetry. Morphological and structural features of these samples were observed by atomic field microscopy and Fourier-transform infrared spectroscopy, respectively. Mechanical properties of the injection and compression moulded composites were evaluated by means of tensile and impact resistance tests. The fracture surface of the impacted samples was observed by scanning electron microscopy. The processing method had a noticeable effect on the results obtained in these tests. Young’s modulus was enhanced up to 147% when adding 5 pph CF to a PP matrix when processed by compression moulding. Addition of PP-g-MAH and CF had a favourable effect on the tensile and impact strength properties in most samples; these composites showed improved performance as the filler content was increased.

Sign in / Sign up

Export Citation Format

Share Document