scholarly journals The Design of a Vapor-Condensing Plume Abatement System and Devices for Mechanical Draft Cooling Towers

Water ◽  
2020 ◽  
Vol 12 (4) ◽  
pp. 1013
Author(s):  
Xiaojing Zhu ◽  
Weihui Xu ◽  
Weishu Wang ◽  
Xu Shi ◽  
Gang Chen ◽  
...  
Keyword(s):  
Cooling Tower ◽  
Engineering Application ◽  
Economic Benefits ◽  
Water Saving ◽  
Cooling Towers ◽  
Confined Space ◽  
Surface Type ◽  
Vapor Plume ◽  
Space Cooling ◽  
Practical Engineering

Cooling towers are widely used in many fields, but the generation of visible plumes has a serious impact on the environment. Moreover, the evaporation losses also cause a great waste of water. In this paper, a vapor-condensing plume abatement system was designed for a mechanical-draft cooling tower based on the mechanism of vapor plume generation. An effective method to achieve water-saving and eliminate the water fog generated in the cooling tower was proposed, and its feasibility was verified by using thermodynamic analysis. Next, the vapor-condensing plume abatement device was designed and used for both the confined space cooling tower (CSCT) and the free space cooling tower (FSCT). The surface type heat exchanger was adopted to design the vapor-condensing plume abatement device. Then a basic calculation flow and method were proposed to obtain thermodynamic operating parameters. According to the comparison between the results of theoretical calculation and practical engineering application, it was found that the designed vapor-condensing plume abatement system obviously benefits the water-saving of a mechanical-draft cooling tower and considerable economic benefits can be obtained. The contents presented provide the theoretical basis and technical support for the upgrade of the cooling tower and the design of the new cooling tower.

scholarly journals Experimental evaluations on the outdoor air-based methods for water saving and plume abatement of cooling tower

2020 ◽  
Vol 15 (3) ◽  
pp. 421-426
Author(s):  
Beomjoon Lee ◽  
Chul Woo Roh ◽  
Bong Soo Choi ◽  
Eunseok Wang ◽  
Ho-Sang Ra ◽  
...  
Keyword(s):  
Power Plant ◽  
Power Plants ◽  
Cooling Tower ◽  
Industrial Sector ◽  
Water Saving ◽  
Membrane Module ◽  
Cooling Power ◽  
Cooling Towers ◽  
Outdoor Air ◽  
Operation Rate

Abstract Cooling towers are widely used not only for commercial and industrial purposes but also for cooling power plant. In Korea, coal-fired power plants and nuclear power plants are generally located on the coast, while most combined-power plants are located inland and use cooling towers to condense steam. The operation rate of power plants in Korea highly depends on government energy policies. In the future, it is expected that the need for cooling tower water for inland power plant will increase. Since power plant is one of the massive water-consuming facilities, methods for water saving of cooling tower should be prepared. Also, in the industrial sector, plume is constantly raising social conflicts between residents and manufactures. Basically, similar technologies can be applied to water saving and plume abatement. In this study, the performance of the condensing module (outdoor-air-condensing method) using outside air was tested first. This module has an advantage in that cooling heat source is not necessary. But an excessive increase of fan air volume is required. We tested a membrane-dehumidification method that selectively transfers water vapor by applying a membrane module. The results showed that membrane module required a large amount of energy to generate vapor pressure difference and it had a disadvantage in energy usage. Since the membrane method considered requires a high bypass airflow for higher dehumidification, it also has a disadvantage similar to that of the outdoor air module. Finally, the dehumidification/regeneration module (heat-pump method) gave the best performance in terms of water saving and plume abatement.

Case study: Theoretical calculation model and variable condition analysis research on the water-splashing noise for natural draft wet cooling towers

2020 ◽  
Vol 68 (2) ◽  
pp. 137-145
Author(s):  
Yang Zhouo ◽  
Ming Gao ◽  
Suoying He ◽  
Yuetao Shi ◽  
Fengzhong Sun
Keyword(s):  
Theoretical Model ◽  
Sound Pressure Level ◽  
Water Droplet ◽  
Water Distribution ◽  
Sound Pressure ◽  
Cooling Tower ◽  
Distribution Patterns ◽  
Calculation Model ◽  
Pressure Level ◽  
Cooling Towers

Based on the basic theory of water droplets impact noise, the generation mechanism and calculation model of the water-splashing noise for natural draft wet cooling towers were established in this study, and then by means of the custom software, the water-splashing noise was studied under different water droplet diameters and water-spraying densities as well as partition water distribution patterns conditions. Comparedwith the water-splashing noise of the field test, the average difference of the theoretical and the measured value is 0.82 dB, which validates the accuracy of the established theoretical model. The results based on theoretical model showed that, when the water droplet diameters are smaller in cooling tower, the attenuation of total sound pressure level of the water-splashing noise is greater. From 0 m to 8 m away from the cooling tower, the sound pressure level of the watersplashing noise of 3 mm and 6 mm water droplets decreases by 8.20 dB and 4.36 dB, respectively. Additionally, when the water-spraying density becomes twice of the designed value, the sound pressure level of water-splashing noise all increases by 3.01 dB for the cooling towers of 300 MW, 600 MW and 1000 MW units. Finally, under the partition water distribution patterns, the change of the sound pressure level is small. For the R s/2 and Rs/3 partition radius (Rs is the radius of water-spraying area), when the water-spraying density ratio between the outer and inner zone increases from 1 to 3, the sound pressure level of water-splashing noise increases by 0.7 dB and 0.3 dB, respectively.

scholarly journals Cooling tower plume abatement and plume modeling: a review

2021 ◽  
Author(s):  
Shuo Li ◽  
M. R. Flynn
Keyword(s):  
Public Health ◽  
Solar Energy ◽  
Cooling Tower ◽  
Plume Rise ◽  
Cooling Towers ◽  
Moist Air ◽  
Novel Technologies ◽  
Plume Modeling ◽  
Dry Cooling Tower ◽  
Dry Cooling

AbstractVisible plumes above wet cooling towers are of great concern due to the associated aesthetic and environmental impacts. The parallel path wet/dry cooling tower is one of the most commonly used approaches for plume abatement, however, the associated capital cost is usually high due to the addition of the dry coils. Recently, passive technologies, which make use of free solar energy or the latent heat of the hot, moist air rising through the cooling tower fill, have been proposed to minimize or abate the visible plume and/or conserve water. In this review, we contrast established versus novel technologies and give a perspective on the relative merits and demerits of each. Of course, no assessment of the severity of a visible plume can be made without first understanding its atmospheric trajectory. To this end, numerous attempts, being either theoretical or numerical or experimental, have been proposed to predict plume behavior in atmospheres that are either uniform versus density-stratified or still versus windy (whether highly-turbulent or not). Problems of particular interests are plume rise/deflection, condensation and drift deposition, the latter consideration being a concern of public health due to the possible transport and spread of Legionella bacteria.

Predicting cooling tower plume dispersion

1997 ◽  
Vol 211 (4) ◽  
pp. 291-297 ◽  
Author(s):  
B E A Fisher
Keyword(s):  
Cooling Tower ◽  
Industrial Process ◽  
Local Environment ◽  
Meteorological Conditions ◽  
Performance Criteria ◽  
Plume Dispersion ◽  
Cooling Towers ◽  
Atmospheric Conditions ◽  
Operating Characteristics

An assessment of the effects of visible cooling tower plumes on the local environment can be a necessary part of any proposal for a new large industrial process. Predictions of the dispersion of plumes from cooling towers are based on methods developed for chimney emissions. However, the kinds of criteria used to judge the acceptability of cooling tower plumes are different from those used for stack plumes. The frequency of long elevated plumes and the frequency of ground fogging are the two main issues. It is shown that events associated with significant plume visibility are dependent both on the operating characteristics of the tower and on the occurrence of certain meteorological conditions. The dependence on atmospheric conditions is shown to be fairly complex and simple performance criteria based on the exit conditions from the tower are not sufficient for assessments.

Design of Cooling Towers by the Effectiveness-NTU Method

1989 ◽  
Vol 111 (4) ◽  
pp. 837-843 ◽  
Author(s):  
H. Jaber ◽  
R. L. Webb
Keyword(s):  
Heat Exchanger ◽  
Cooling Tower ◽  
Design Method ◽  
Design Methods ◽  
Parallel Flow ◽  
Basic Method ◽  
Cooling Towers ◽  
Flow Configuration ◽  
Heat Exchanger Design

This paper develops the effectiveness-NTU design method for cooling towers. The definitions for effectiveness and NTU are totally consistent with the fundamental definitions used in heat exchanger design. Sample calculations are presented for counter and crossflow cooling towers. Using the proper definitions, a person competent in heat exchanger design can easily use the same basic method to design a cooling tower of counter, cross, or parallel flow configuration. The problems associated with the curvature of the saturated air enthalpy line are also treated. A “one-increment” design ignores the effect of this curvature. Increased precision can be obtained by dividing the cooling range into two or more increments. The standard effectiveness-NTU method is then used for each of the increments. Calculations are presented to define the error associated with different numbers of increments. This defines the number of increments required to attain a desired degree of precision. The authors also summarize the LMED method introduced by Berman, and show that this is totally consistent with the effectiveness-NTU method. Hence, using proper and consistent terms, heat exchanger designers are shown how to use either the standard LMED or effectiveness-NTU design methods to design cooling towers.

Dynamic Characteristics and Stability Analysis of Two-Dimensional (2D) Electro-Hydraulic Proportional Directional Valve

2015 ◽  
Author(s):  
S. Li ◽  
J. Ruan ◽  
B. Meng ◽  
W. A. Jia ◽  
H. Y. Xie
Keyword(s):  
Dynamic Characteristics ◽  
Magnetic Force ◽  
Engineering Application ◽  
Proportional Valve ◽  
Acceptable Range ◽  
Hydrostatic Force ◽  
Practical Engineering ◽  
Direct Operation ◽  
Electrohydraulic Valve ◽  
Proportional Directional Valve

A 2D electrohydraulic proportional directional valve is proposed, which integrates both direct and pilot operation of the valve. In this valve, the output magnetic force of the proportional solenoid is converted to rotate the spool through a thrust-torsion coupling and thus the pressure in the valve sensitive chamber is varied. The varied pressure exerted on the areas of the spool end produces a hydrostatic force to move the spool linearly, which will rotate the spool reversely. Theoretical analysis is carried to the proposed valve and the effects of the key geometric parameters on the dynamic characteristics of the 2D valve and stability are investigated. Experiments are also designed to access to the characteristics of the valve working under direct and pilot operation. The 2D electrohydraulic valve can work properly for both direct operation and pilot operation. The hysteresis and frequency response are measured and the results are within the acceptable range in practical engineering application required of the directional proportional valve.

Analysis of Heat, Mass, and Momentum Transfer in the Rain Zone of Counterflow Cooling Towers

1999 ◽  
Vol 121 (4) ◽  
pp. 751-755 ◽  
Author(s):  
E. de Villiers ◽  
D. G. Kro¨ger
Keyword(s):  
Momentum Transfer ◽  
Cooling Tower ◽  
Mechanical Energy ◽  
Performance Evaluations ◽  
Cooling Towers ◽  
Droplet Deformation ◽  
One Dimensional ◽  
Mechanical Energy Loss ◽  
Simplifying Assumptions ◽  
Semi Empirical

The rate of heat, mass, and momentum transfer in the rain zone of three counterflow cooling tower geometries is analyzed using simplifying assumptions and numerical integration. The objective of the analysis is to generate equations for use in a one-dimensional mathematical cooling tower performance evaluations. Droplet deformation is taken into account and momentum transfer is calculated from the air flow’s mechanical energy loss, caused by air-droplet interaction. A comparison of dimensionless semi-empirical equations and experimental data demonstrates the method’s capability to predict the pressure drop in a counterflow rain zone.

Experimental and Theoretical Studies on Performance of GSHP Combined with Free Cooling System

2013 ◽  
Vol 368-370 ◽  
pp. 1232-1236
Author(s):  
Wei Xue Cao ◽  
Ru Chang ◽  
Can Zhang ◽  
Qiu Li Zhang
Keyword(s):  
Cooling Tower ◽  
Cooling System ◽  
Meteorological Parameter ◽  
Economic Benefits ◽  
Ground Source Heat Pump ◽  
Combined System ◽  
Climate Zones ◽  
Ground Source ◽  
Free Cooling ◽  
Experimental And Theoretical Studies

Ground-Source Heat Pump systems and tower cooling system have been studied in this paper individually by experiment and simulation using TRNSYS, the influencing factors such as meteorological parameter, cooling tower and subunit construction was analyzed. Results show that the combined system has ability to meet the cooling requirements in II building climate zones, the combined system will have energy-saving and obvious economic benefits by working through the year.

scholarly journals On Thermal Performance of Seawater Cooling Towers

2010 ◽  
Author(s):  
Mostafa H. Sharqawy ◽  
John H. Lienhard ◽  
Syed M. Zubair
Keyword(s):  
Thermal Conductivity ◽  
Power Generation ◽  
Thermal Performance ◽  
Cooling Tower ◽  
Cooling Towers ◽  
Governing Equations ◽  
Detailed Model ◽  
Salt Deposition ◽  
Transfer Processes ◽  
Mass Transfer Processes

Seawater cooling towers have been used since the 1970’s in power generation and other industries, so as to reduce the consumption of freshwater. The salts in seawater are known to create a number of operational problems including salt deposition, packing blockage, corrosion, and certain environmental impacts from salt drift and blowdown return. In addition, the salinity of seawater affects the thermophysical properties which govern the thermal performance of cooling towers, including vapor pressure, density, specific heat, viscosity, thermal conductivity and surface tension. In this paper, the thermal performance of seawater cooling towers is investigated using a detailed model of a counterflow wet cooling tower. The model takes into consideration the coupled heat and mass transfer processes and does not make any of the conventional Merkel approximations. In addition, the model incorporates the most up-to-date seawater properties in the literature. The model governing equations are solved numerically and its validity is checked by data in the literature. Based on the results of the model, a correction factor is obtained which characterizes the degradation of the cooling tower effectiveness when seawater is used.

Sign in / Sign up

Export Citation Format

Share Document