scholarly journals Scale up of Microbial Fuel Cell Stack System for Residential Wastewater Treatment in Continuous Mode Operation

Water ◽  
2019 ◽  
Vol 11 (2) ◽  
pp. 217 ◽  
Author(s):  
Rodrigo Valladares Linares ◽  
Jorge Domínguez-Maldonado ◽  
Ernesto Rodríguez-Leal ◽  
Gabriel Patrón ◽  
Alfonso Castillo-Hernández ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
Scale Up ◽  
Oxygen Demand ◽  
Domestic Wastewater ◽  
Septic Tank ◽  
Efficient Technology ◽  
Fuel Cell Stack ◽  
Treated Effluent

The most important operational expense during wastewater treatment is electricity for pumping and aeration. Therefore, this work evaluated operational parameters and contaminant removal efficiency of a microbial fuel cell stack system (MFCSS) that uses no electricity. This system consists of (i) septic tank primary treatment, (ii) chamber for secondary treatment containing 18 MFCs, coupled to an energy-harvesting circuit (EHC) that stores the electrons produced by anaerobic respiration, and (iii) gravity-driven disinfection (sodium hypochlorite 5%). The MFCSS operated during 60 days (after stabilization period) and it was gravity-fed with real domestic wastewater from a house (5 inhabitants). The flow rate was 600 ± 100 L∙d−1. The chemical oxygen demand, biological oxygen demand, total nitrogen and total phosphorous were measured in effluent, with values of 100 ± 10; 12 ± 2; 9.6 ± 0.5 and 4 ± 0.2 mg∙L−1, and removal values of 86%, 87%, 84% and 64%, respectively. Likewise, an EHC (ultra-low energy consumption) was built with 6.3 V UCC® 4700 µF capacitors that harvested and stored energy from MFCs in parallel. Energy management was programmed on a microcontroller Atmega 328PB®. The water quality of the treated effluent complied with the maximum levels set by the Mexican Official Standard NOM-001-SEMARNAT-1996-C. A cost analysis showed that MFCSS could be competitive as a sustainable and energy-efficient technology for real domestic wastewater treatment.

Performance evaluation of package plant for treatment of single household domestic wastewater

2016 ◽  
Vol 11 (1) ◽  
pp. 1-9 ◽  
Author(s):  
Meena Kumari Sharma ◽  
Absar Ahmad Kazmi
Keyword(s):  
Developing Countries ◽  
Removal Efficiency ◽  
Urban Areas ◽  
Oxygen Demand ◽  
Domestic Wastewater ◽  
Post Treatment ◽  
Pollutant Removal ◽  
Septic Tank ◽  
Efficient Technology ◽  
Treated Effluent

This study was carried out to evaluate the performance of an anaerobic packaged onsite system as an alternative to septic tank for the rural and semi-urban areas of developing countries where centralized sewerage facilities are not available. Potential application was identified on the basis of pollutant removal efficiency. The average per-capita wastewater generation was found to be 140 L/person/day with maximum contribution from the kitchen. The average removal efficiency of the system for chemical oxygen demand (COD), biochemical oxygen demand, total suspended solids, total nitrogen, total phosphate and fecal coliform was 70.9 ± 11.8%, 68.7 ± 8.5%, 78.1 ± 4.7%, 20.2 ± 8.4%, 13.8 ± 3.7% and 86.5 ± 1.6%, respectively. Despite a satisfactory performance, the anaerobically-treated effluent did not meet the disposal standards and required subsequent post treatment. An electrochemical reactor with aluminium electrodes, at a potential difference of 12 V, showed appreciable potential for use in actual households as a post treatment option for further removal of the pathogens and COD. The treated domestic wastewater, with electrocoagulation as a post-treatment measure, was successfully reused for non-potable purposes. Therefore, the package system, in conjugation with electrocoagulation process, promises to be a highly efficient technology for the onsite treatment of domestic wastewater in developing countries while facilitating reuse of the treated effluent for various recreational purposes as well as a safe discharge.

scholarly journals Effect of Anolyte pH on the Performance of a Dual-Chambered Microbial Fuel Cell Operated with Different Biomass Feed

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Md. Abdul Halim ◽  
Md. Owaleur Rahman ◽  
Mohammad Ibrahim ◽  
Rituparna Kundu ◽  
Biplob Kumar Biswas
Keyword(s):  
Wastewater Treatment ◽  
Fuel Cell ◽  
River Water ◽  
Microbial Fuel Cell ◽  
Alternative Energy ◽  
Coulombic Efficiency ◽  
Oxygen Demand ◽  
Cod Removal ◽  
Bioelectricity Generation ◽  
Alternative Energy Resources

Finding sustainable alternative energy resources and treating wastewater are the two most important issues that need to be solved. Microbial fuel cell (MFC) technology has demonstrated a tremendous potential in bioelectricity generation with wastewater treatment. Since wastewater can be used as a source of electrolyte for the MFC, the salient point of this study was to investigate the effect of pH on bioelectricity production using various biomass feed (wastewater and river water) as the anolyte in a dual-chambered MFC. Maximum extents of power density (1459.02 mW·m−2), current density (1288.9 mA·m−2), and voltage (1132 mV) were obtained at pH 8 by using Bhairab river water as a feedstock in the MFC. A substantial extent of chemical oxygen demand (COD) removal (94%) as well as coulombic efficiency (41.7%) was also achieved in the same chamber at pH 8. The overall performance of the MFC, in terms of bioelectricity generation, COD removal, and coulombic efficiency, indicates a plausible utilization of the MFC for wastewater treatment as well as bioelectricity production.

Multiple anodic chambers sharing an algal raceway pond to establish a photosynthetic microbial fuel cell stack: Voltage boosting accompany wastewater treatment

2019 ◽  
Vol 164 ◽  
pp. 114955 ◽  
Author(s):  
Zhigang Yang ◽  
Lijie Zhang ◽  
Changliang Nie ◽  
Qingjie Hou ◽  
Shasha Zhang ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
Fuel Cell Stack ◽  
Raceway Pond

scholarly journals Wastewater Treatment and Electricity Production in a Microbial Fuel Cell with Cu–B Alloy as the Cathode Catalyst

Catalysts ◽  
2019 ◽  
Vol 9 (7) ◽  
pp. 572 ◽  
Author(s):  
Paweł P. Włodarczyk ◽  
Barbara Włodarczyk
Keyword(s):  
Wastewater Treatment ◽  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
Microbial Fuel Cells ◽  
Oxygen Demand ◽  
Electricity Production ◽  
Cathode Catalyst ◽  
Similar Reduction ◽  
Fuel Cell Operation

The possibility of wastewater treatment and electricity production using a microbial fuel cell with Cu–B alloy as the cathode catalyst is presented in this paper. Our research covered the catalyst preparation; measurements of the electroless potential of electrodes with the Cu–B catalyst, measurements of the influence of anodic charge on the catalytic activity of the Cu–B alloy, electricity production in a microbial fuel cell (with a Cu–B cathode), and a comparison of changes in the concentration of chemical oxygen demand (COD), NH4+, and NO3– in three reactors: one excluding aeration, one with aeration, and during microbial fuel cell operation (with a Cu–B cathode). During the experiments, electricity production equal to 0.21–0.35 mA·cm−2 was obtained. The use of a microbial fuel cell (MFC) with Cu–B offers a similar reduction time for COD to that resulting from the application of aeration. The measured reduction of NH4+ was unchanged when compared with cases employing MFCs, and it was found that effectiveness of about 90% can be achieved for NO3– reduction. From the results of this study, we conclude that Cu–B can be employed to play the role of a cathode catalyst in applications of microbial fuel cells employed for wastewater treatment and the production of electricity.

High speed municipal sewage treatment in microbial fuel cell integrated with anaerobic membrane filtration system

2014 ◽  
Vol 69 (12) ◽  
pp. 2548-2553 ◽  
Author(s):  
Y. Lee ◽  
S. W. Oa
Keyword(s):  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
High Speed ◽  
Membrane Filtration ◽  
Membrane Filter ◽  
Oxygen Demand ◽  
Domestic Wastewater ◽  
Organic Substrate ◽  
Municipal Sewage ◽  
Filtration System

A cylindrical two chambered microbial fuel cell (MFC) integrated with an anaerobic membrane filter was designed and constructed to evaluate bioelectricity generation and removal efficiency of organic substrate (glucose or domestic wastewater) depending on organic loading rates (OLRs). The MFC was continuously operated with OLRs 3.75, 5.0, 6.25, and 9.38 kg chemical oxygen demand (COD)/(m3·d) using glucose as a substrate, and the cathode chamber was maintained at 5–7 mg/L of dissolved oxygen. The optimal OLR was found to be 6.25 kgCOD/(m3·d) (hydraulic retention time (HRT) 1.9 h), and the corresponding voltage and power density averaged during the operation were 0.15 V and 13.6 mW/m3. With OLR 6.25 kgCOD/(m3·d) using domestic wastewater as a substrate, the voltage and power reached to 0.13 V and 91 mW/m3 in the air cathode system. Even though a relatively short HRT of 1.9 h was applied, stable effluent could be obtained by the membrane filtration system and the following air purging. In addition, the short HRT would provide economic benefit in terms of reduction of construction and operating costs compared with a conventional aerobic treatment process.

scholarly journals Microbial Fuel Cell with Ni–Co Cathode Powered with Yeast Wastewater

Energies ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 3194 ◽  
Author(s):  
Paweł Włodarczyk ◽  
Barbara Włodarczyk
Keyword(s):  
Wastewater Treatment ◽  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
Sewage Treatment ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Electricity Production ◽  
High Concentration ◽  
Yeast Wastewater

Wastewater originating from the yeast industry is characterized by high concentration of pollutants that need to be reduced before the sludge can be applied, for instance, for fertilization of croplands. As a result of the special requirements associated with the characteristics of this production, huge amounts of wastewater are generated. A microbial fuel cell (MFC) forms a device that can apply wastewater as a fuel. MFC is capable of performing two functions at the same time: wastewater treatment and electricity production. The function of MFC is the production of electricity during bacterial digestion (wastewater treatment). This paper analyzes the possibility of applying yeast wastewater to play the function of a MFC (with Ni–Co cathode). The study was conducted on industrial wastewater from a sewage treatment plant in a factory that processes yeast sewage. The Ni–Co alloy was prepared by application of electrochemical method on a mesh electrode. The results demonstrated that the use of MFC coupled with a Ni–Co cathode led to a reduction in chemical oxygen demand (COD) by 90% during a period that was similar to the time taken for reduction in COD in a reactor with aeration. The power obtained in the MFC was 6.1 mW, whereas the volume of energy obtained during the operation of the cell (20 days) was 1.27 Wh. Although these values are small, the study found that this process can offer an additional level of wastewater treatment as a huge amount of sewage is generated in the process. This would provide an initial reduction in COD (and save the energy needed to aerate wastewater) as well as offer the means to generate electricity.

Sign in / Sign up

Export Citation Format

Share Document