scholarly journals Physical and Mechanical Characterization of Sustainable and Innovative Porous Concrete for Urban Pavements Containing Metakaolin

2020 ◽  
Vol 12 (10) ◽  
pp. 4243 ◽  
Author(s):  
Eduardo-Javier Elizondo-Martinez ◽  
Piergiorgio Tataranni ◽  
Jorge Rodriguez-Hernandez ◽  
Daniel Castro-Fresno
Keyword(s):  
Tensile Strength ◽  
Environmental Impacts ◽  
Indirect Tensile Strength ◽  
Partial Substitution ◽  
Concrete Pavements ◽  
Suitable Alternative ◽  
Porous Concrete ◽  
Concrete Mixtures ◽  
Alternative Materials ◽  
Indirect Tensile

Alternative materials to replace cement in pavements have recently been widely studied with the purpose of decreasing the environmental impacts that the construction industry generates. In this context, the implementation of sustainable urban drainage systems has grown, especially with porous pavements, with the intention to reduce water and environmental impacts. In the present investigation, the addition of alternative materials to minimize the use of cement in porous concrete pavements is evaluated. Starting from a partial substitution of Portland cement with metakaolin, experimental geopolymer concretes were produced with metakaolin and waste basalt powder according to several dosages. Two sets of mixtures were analyzed to evaluate the Porous Concrete Design (PCD) methodology for porous concrete mixtures with alternative materials. A deep analysis was proposed for the evaluation of the mechanical and volumetric properties of the mixtures. Results demonstrated that replacing 5% of cement with metakaolin can increase both permeability and indirect tensile strength. Geopolymer mixtures can achieve permeability significantly higher than the traditional porous concrete, but this decreases their indirect tensile strength. However, considering the promising results, an adjustment in the mix design of the geopolymer mixtures could increase their mechanical properties without negatively affecting the porosity, making these materials a suitable alternative to traditional porous cement concrete, and a solution to be used in urban pavements.

scholarly journals Asphalt concrete mixtures with addition of reclaimed asphalt pavements

2021 ◽  
Author(s):  
Piotr Zieliński
Keyword(s):  
Tensile Strength ◽  
Asphalt Concrete ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Asphalt Pavements ◽  
Stiffness Modulus ◽  
Reclaimed Asphalt ◽  
Concrete Mixtures ◽  
Indirect Tensile ◽  
Reclaimed Asphalt Pavements

The effect of using reclaimed asphalt pavements (RAP) to asphalt concrete mixtures besides their utilization is to reduce the amount of the new bituminous binder and aggregate added to hot mix asphalt. This publication presents studies on asphalt mixtures with an increased up to 40% amount of RAP additive with the simultaneous use of 2 types of added bitumen, i.e. 35/50 and PMB 25/55-60. The aim of the paper is the evaluation of the basic mixture properties in a wide range of operating temperatures, as a part of the AC testing at high temperatures, the resistance to rutting at 60° C and indirect tensile strength at 40° C. The assessment of properties at intermediate operating temperatures is based on indirect tensile tests, including: elastic stiffness modulus at 5° C, 15° C and 30° C and static strength at 25° C. The low temperature properties have been tested in water and frost resistance tests by indirect tensile strength ratio. The results of the study were subjected to the analysis of the statistical significance of differences, which showed an improvement in the resistance of AC with the addition of RAP to the formation of permanent deformations and an increase in the stiffness modulus as well as indirect tensile strength. There was no adverse effect of the RAP additive on asphalt mixtures resistance to water and frost action.

scholarly journals Characteristics of Bituminous Concrete Mixtures Utilizing Copper Slag

2021 ◽  
Vol 10 (1) ◽  
pp. 1-10
Author(s):  
Chavan Ravishankar ◽  
M.S. Nagakumar ◽  
H.K. Krishnegowda ◽  
Abhilash R Prasad
Keyword(s):  
Tensile Strength ◽  
Copper Slag ◽  
Indirect Tensile Strength ◽  
Concrete Mixtures ◽  
Static Tensile ◽  
Indirect Tensile ◽  
High Level ◽  
Mineral Fillers ◽  
By Products ◽  
Bituminous Concrete

Study work on the effectiveness and use of Industrial by-products (IBP) in flexible pavements is restricted. Several factors however need to be analyzed specifically before a greater proportion of industrial by-products can be used in bituminous concrete mixtures with a high level of confidence. Effects of copper slag on volumetric and strength parameters such as Marshall Parameters, static tensile properties, and moisture resistivity of bituminous concrete mixtures using copper slag as mineral fillers need to be examined and thoroughly analyzed. Quantitative analyses of the elements and the morphology of the copper slag have been studied by Energy Dispersive X-ray Analyzer (EDX) and Scanning Electron Microscope (SEM). The use of copper slag as a mineral filler in bituminous concrete grade-2 mixtures showed an increase in stability, indirect tensile strength, and moisture resistance compared to traditional mixtures. Keywords— Industrial by-products (IBP), Indirect Tensile Strength, Moisture resistivity, SEM, EDX

scholarly journals Rejuvenation Mechanism of Asphalt Mixtures Modified with Crumb Rubber

CivilEng ◽  
2021 ◽  
Vol 2 (2) ◽  
pp. 370-384
Author(s):  
Hossein Noorvand ◽  
Kamil Kaloush ◽  
Jose Medina ◽  
Shane Underwood
Keyword(s):  
Tensile Strength ◽  
Dynamic Loading ◽  
Creep Compliance ◽  
Asphalt Mixture ◽  
Crumb Rubber ◽  
Indirect Tensile Strength ◽  
Laboratory Evaluation ◽  
Strength Testing ◽  
Noise Mitigation ◽  
Indirect Tensile

Asphalt aging is one of the main factors causing asphalt pavements deterioration. Previous studies reported on some aging benefits of asphalt rubber mixtures through laboratory evaluation. A field observation of various pavement sections of crumb rubber modified asphalt friction courses (ARFC) in the Phoenix, Arizona area indicated an interesting pattern of transverse/reflective cracking. These ARFC courses were placed several years ago on existing jointed plain concrete pavements for highway noise mitigation. Over the years, the shoulders had very noticeable and extensive cracking over the joints; however, the driving lanes of the pavement showed less cracking formation in severity and extent. The issue with this phenomenon is that widely adopted theories that stem from continuum mechanics of materials and layered mechanics of pavement systems cannot directly explain this phenomenon. One hypothesis could be that traffic loads continually manipulate the pavement over time, which causes some maltenes (oils and resins) compounds absorbed in the crumb rubber particles to migrate out leading to rejuvenation of the mastic in the asphalt mixture. To investigate the validity of such a hypothesis, an experimental laboratory testing was undertaken to condition samples with and without dynamic loads at high temperatures. This was followed by creep compliance and indirect tensile strength testing. The results showed the higher creep for samples aged with dynamic loading compared to those aged without loading. Higher creep compliance was attributed to higher flexibility of samples due to the rejuvenation of the maltenes. This was also supported by the higher fracture energy results obtained for samples conditioned with dynamic loading from indirect tensile strength testing.

scholarly journals Evaluations of Nano-Sized Hydrated Lime on the Moisture Susceptibility of Hot Mix Asphalt Mixtures

2012 ◽  
Vol 174-177 ◽  
pp. 82-90 ◽  
Author(s):  
Ju Nan Shen ◽  
Zhao Xing Xie ◽  
Fei Peng Xiao ◽  
Wen Zhong Fan
Keyword(s):  
Tensile Strength ◽  
Experimental Design ◽  
Hot Mix Asphalt ◽  
Hydrated Lime ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Moisture Resistance ◽  
Strength Ratio ◽  
Moisture Susceptibility ◽  
Indirect Tensile

The objective of this study was to evaluate the effect of nano-sized hydrated lime on the moisture susceptibility of the hot mix asphalt (HMA) mixtures in terms of three methodologies to introduce into the mixtures. The experimental design for this study included the utilizations of one binder source (PG 64-22), three aggregate sources and three different methods introducing the lime. A total of 12 types of HMA mixtures and 72 specimens were fabricated and tested in this study. The performed properties include indirect tensile strength (ITS), tensile strength ratio (TSR), flow, and toughness. The results indicated that the nano-sized lime exhibits better moisture resistance. Introducing process of the nano-sized lime will produce difference in moisture susceptibility.

scholarly journals Relations between indirect tensile and flexural strengths for dry and plastic concretes

2013 ◽  
Vol 6 (6) ◽  
pp. 854-874 ◽  
Author(s):  
J. T. Balbo
Keyword(s):  
Tensile Strength ◽  
Concrete Slab ◽  
Plane Stress State ◽  
Concrete Mixtures ◽  
Technological Control ◽  
Strength Tests ◽  
Indirect Tensile ◽  
Actual Strength ◽  
Basic Concepts ◽  
Set Up

Indirect tensile strength is not usually used for concrete mixtures proportioning and its technological control; flexural strength tests under third point loads arrangement are the pattern for such goals. Indeed, neither of such tests have the capability to set up the actual strength of a concrete slab since its response is under plane stress state. A critical review of the basic concepts on both kinds of tests allows foreseeing its limitations as well as how to overcome such shortcomings. At last correlations between the two kinds of tensile strength are presented considering dry and plastic concretes typically applied on paving, corroborating to former results achieved for plastic concretes.

scholarly journals Laboratory Evaluation of the Use of Florida Washed Shell in Open-Graded Asphalt Mixtures

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 7060
Author(s):  
Mohammad Alharthai ◽  
Qing Lu ◽  
Ahmed Elnihum ◽  
Asad Elmagarhe
Keyword(s):  
Tensile Strength ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Laboratory Evaluation ◽  
Void Content ◽  
Coarse Aggregates ◽  
Significant Difference ◽  
Indirect Tensile ◽  
Marshall Stability

This study investigates the substitution of conventional aggregate with a Florida washed shell in open-graded asphalt mixtures and evaluates the optimal substitution percentage in aggregate gradations of various nominal maximum aggregate sizes (NMASs) (i.e., 4.75, 9.5, and 12.5 mm). Laboratory experiments were performed on open-graded asphalt mixture specimens with the coarse aggregate of sizes between 2.36 and 12.5 mm being replaced by the Florida washed shell at various percentages (0, 15, 30, 45, and 100%). Specimen properties relevant to the performance of open-graded asphalt mixtures in the field were tested, evaluated, and compared. Specifically, a Marshall stability test, Cantabro test, indirect tensile strength test, air void content test, and permeability test were conducted to evaluate the strength, resistance to raveling, cracking resistance, void content, and permeability of open-graded asphalt mixtures. The results show that there is no significant difference in the Marshall stability and indirect tensile strength when the coarse aggregates are replaced with Florida washed shell. This study also found that the optimum percentages of Florida washed shell in open-graded asphalt mixture were 15, 30, and 45% for 12.5, 9.5, and 4.75 mm NMAS gradations, respectively.

Sign in / Sign up

Export Citation Format

Share Document