scholarly journals Evaluation of Dust Concentration During Grinding Grain in Sustainable Agriculture

2019 ◽  
Vol 11 (17) ◽  
pp. 4572 ◽  
Author(s):  
Sobczak ◽  
Mazur ◽  
Zawiślak ◽  
Panasiewicz ◽  
Żukiewicz-Sobczak ◽  
...  
Keyword(s):  
Moisture Content ◽  
Sustainable Agriculture ◽  
Inverse Relationship ◽  
Dust Concentration ◽  
Grinding Process ◽  
Hammer Mill ◽  
Health It ◽  
Organic Dust ◽  
Roller Mill ◽  
Grain Moisture

This work analyses the organic dust concentration during a wheat grinding process which was carried out using two types of grinders: A hammer mill and a roller mill. DustTrak II aerosol monitor was used to measure the concentration of the dust PM10 (particles with the size smaller than 10 μm), PM4.0, and PM1.0. An increase of the grain moisture to 14% resulted in the reduction in PM10 when grinding grain using the hammer mill. An inverse relationship was obtained when grain was ground using the roller mill. A smaller amount of the fraction below 0.1 mm was observed for larger diameter of the holes in the screen and smaller size of the working gap in the roller mill. For both mills, the obtained concentration of the PM10 fraction dust exceeded the acceptable level. To protect farmers health, it is necessary to use dust protection equipment or to modify the grinding technology by changing the grain moisture content and/or the grinding parameters.

PARAMETER OPTIMIZATION AND EXPERIMENTAL RESEARCH ON THE HAMMER MILL 锤片式粉碎机参数优化与试验研究

2020 ◽  
pp. 341-350
Author(s):  
Di Wang ◽  
Changbin He ◽  
Haiqing Tian ◽  
Liu Fei ◽  
Zhang Tao ◽  
...  
Keyword(s):  
Moisture Content ◽  
Orthogonal Experiment ◽  
Electricity Consumption ◽  
Spindle Speed ◽  
Hammer Mill ◽  
Factors Affecting ◽  
Evaluation Indexes ◽  
Grain Moisture ◽  
Validation Experiment ◽  
Corn Grain

Low productivity and high electricity consumption are considered problems of the hammer mill, which is widely used in current feed production. In this paper, the mechanical properties of corn grain ground by a hammer mill were analysed, and the key factors affecting the performance of the hammer mill were determined. The single-factor experiment and three-factor, three-level quadratic regression orthogonal experiment were carried out with the spindle speed, corn grain moisture content and number of hammers as experimental factors and the productivity and electricity consumption per ton as evaluation indexes. The results showed that the order of influence on the productivity was spindle speed > corn grain moisture content > number of hammers and that the order of influence on the electricity consumption per ton was corn grain moisture content > spindle speed > number of hammers. The parameters were optimized based on the response surface method with the following results: the spindle speed was 4306 r/min, the corn grain moisture content was 10%, and the number of hammers was 24. The validation experiment was carried out with the optimal parameters’ combination. The productivity and electricity consumption per ton were 988.12 kg/h and 5.37 kW·h/t, respectively, which were consistent with the predicted results of the model.

scholarly journals Wheat Grinding Process with Low Moisture Content: A New Approach for Wholemeal Flour Production

Processes ◽  
2020 ◽  
Vol 9 (1) ◽  
pp. 32
Author(s):  
Waleed H. Hassoon ◽  
Dariusz Dziki ◽  
Antoni Miś ◽  
Beata Biernacka
Keyword(s):  
Particle Size ◽  
Moisture Content ◽  
Average Particle Size ◽  
Average Particle ◽  
Grinding Process ◽  
Mixing Properties ◽  
New Approach ◽  
Grain Moisture ◽  
Flour Production ◽  
And Storage

The objective of this study was to determine the grinding characteristics of wheat with a low moisture content. Two kinds of wheat—soft spelt wheat and hard Khorasan wheat—were dried at 45 °C to reduce the moisture content from 12% to 5% (wet basis). Air drying at 45 °C and storage in a climatic chamber (45 °C, 10% relative humidity) were the methods used for grain dehydration. The grinding process was carried out using a knife mill. After grinding, the particle size distribution, average particle size and grinding energy indices were determined. In addition, the dough mixing properties of wholemeal flour dough were studied using a farinograph. It was observed that decreasing the moisture content in wheat grains from 12% to 5% made the grinding process more effective. As a result, the average particle size of the ground material was decreased. This effect was found in both soft and hard wheat. Importantly, lowering the grain moisture led to about a twofold decrease in the required grinding energy. Moreover, the flour obtained from the dried grains showed higher water absorption and higher dough stability during mixing. However, the method of grain dehydration had little or no effect on the results of the grinding process or dough properties.

scholarly journals The effect of seed moisture and temperature on grinding characteristics of quinoa (Chenopodium quinoa Willd.)

2018 ◽  
Vol 10 ◽  
pp. 01006 ◽  
Author(s):  
Waleed Hameed Hassoon ◽  
Dariusz Dziki
Keyword(s):  
Moisture Content ◽  
Fine Particles ◽  
Chenopodium Quinoa ◽  
Energy Requirements ◽  
Average Particle ◽  
Grinding Process ◽  
Seed Moisture Content ◽  
Seed Moisture ◽  
Grain Moisture ◽  
Amino Acid Balance

Quinoa (Chenopodium quinoa Willd) is a native food plant of the Andean region of South America. Quinoa seeds have remarkable nutritional properties, not only from its high protein content, but also from its good amino acid balance. The aim of the study was evaluate the influence of quinoa seed moisture content (10, 12, 14, 16 and 18%) and temperature (-20, 3, 20 and 40°C, with the initial grain moisture content of 10.5%) on grinding process. Especially the particle size distributions and grinding energy indices were determined. The results showed that the increase of seed moisture content from 10 to 16% caused an increase the specific grinding energy from 6.9 to 8.3 kJ·kg-1, beside of this as the moisture increased the average particle also increased. The highest changes were observed in the fraction of coarse particles (above 1.0 mm). Interestingly, the mass fraction of fine particles (below 0.2 mm also increased). Other grinding indices also confirmed an increase the grinding energy requirements with the increase seed moisture content. The temperature of seed has little influence on quinoa grinding process. The highest grinding energy requirements were observed when the frozen seeds were ground.

Effects of Non-uniform Kernel Moisture Content on Moisture Measurement of Corn

2005 ◽  
Vol 1 (1) ◽  
pp. 77-93
Author(s):  
Bíborka Gillay ◽  
David B. Funk
Keyword(s):  
Moisture Content ◽  
Moisture Measurement ◽  
Safe Storage ◽  
Grain Moisture ◽  
Moisture Meter ◽  
Percent Moisture ◽  
New Crop ◽  
The U.S

The price paid for corn is usually based on 15.0 or 15.5 percent moisture content. However, corn must be dried below 13 percent moisture to ensure safe storage for a year or more. In the U.S., such stored corn cannot be directly remoistened before selling it, but it can be mixed with moist new-crop corn. Accurate moisture measurement of mixtures of dry and moist corn is important to permit adjustment of blending ratios to maximize profitability, but grain moisture meters are less accurate for mixtures of wet and dry grain. This research evaluated the differences between dielectric-type moisture meter results for mixed and equilibrated corn samples at different moisture levels and different measurement frequencies. Equilibrated grain samples tended to give lower moisture results than recently mixed grain samples - especially in the 1 to 10 MHz region. These differences permitted detection of mixtures by using moisture measurements at two frequencies.

Effects of Grain Moisture Content on Mechanical Grain Harvesting Quality of Summer Maize

2018 ◽  
Vol 44 (12) ◽  
pp. 1747 ◽  
Author(s):  
Lu-Lu LI ◽  
Jun XUE ◽  
Rui-Zhi XIE ◽  
Ke-Ru WANG ◽  
Bo MING ◽  
...  
Keyword(s):  
Moisture Content ◽  
Summer Maize ◽  
Grain Moisture

Intensive beef production 6. A note on the nutritive value of high moisture barley stored anaerobically

1965 ◽  
Vol 7 (3) ◽  
pp. 385-387 ◽  
Author(s):  
T. R. Preston ◽  
H. B. Bowers ◽  
N. A. MacLeod ◽  
Euphemia B. Phillip
Keyword(s):  
Moisture Content ◽  
Nutritive Value ◽  
Feeding System ◽  
Beef Production ◽  
Anaerobic Conditions ◽  
High Moisture ◽  
Roller Mill ◽  
Barley Husk

The use of barley for intensive beef production, as described by Preston, Aitken, Whitelaw, Macdearmid, MacLeod and Philip (1963) is now a well established practice, but one of the hazards of this feeding system is bloat. There is evidence that the risk of this condition is accentuated if the barley husk is broken down too finely as happens if the grain is ground (Preston, Macdearmid and MacLeod, 1963; Preston, 1964). It was therefore recommended that barley should be processed in a roller mill and that the moisture content should be at least 16% (Preston, 1963), for if the grain is drier than this it is difficult to prevent excessive shattering and destruction of the husk. Suitable containers, which can be sealed in order to ensure anaerobic conditions and so overcome the problem of storing damp grain (greater than 16% moisture) have additional advantages at harvest since they can be filled quickly and easily. The purpose of this experiment was to evaluate the nutritive value of barley stored under these conditions.

Maize grain moisture content correction: From nonstandard to standard system

2021 ◽  
Vol 204 ◽  
pp. 212-222
Author(s):  
Shang Gao ◽  
Bo Ming ◽  
Lu-lu Li ◽  
Rui-zhi Xie ◽  
Ke-ru Wang ◽  
...  
Keyword(s):  
Moisture Content ◽  
Standard System ◽  
Grain Moisture ◽  
Maize Grain

255 Evaluation of Different Corn Milling Methods for High-moisture and Dry Corn on Nutrient Digestion

2021 ◽  
Vol 99 (Supplement_1) ◽  
pp. 124-125
Author(s):  
Caitlin A Coulson ◽  
Nicole Woita ◽  
Tyler Spore ◽  
Hannah Wilson ◽  
Kylie Butterfield ◽  
...  
Keyword(s):  
Dry Matter ◽  
Milling Process ◽  
Nutrient Digestibility ◽  
Hammer Mill ◽  
High Moisture ◽  
Roller Mill ◽  
Nutrient Digestion ◽  
Milling Method ◽  
Feeding Diets ◽  
Effect Of Feeding

Abstract A 2 × 2 factorial digestion study using seven ruminally cannulated steers evaluated the effect of feeding diets containing 70% (dry matter-basis) high-moisture (HMC) or dry corn (DC), processed with either a hammer mill or Automatic Ag Roller Mill (Pender, NE), on nutrient digestion. Feeding HMC decreased the amount of excreted dry matter (DM) and organic matter (OM; P ≤ 0.01) regardless of mill type, but there was a tendency (P ≤ 0.13) for an interaction between corn type and mill type for DM and OM digestibility. There was no difference between either milling treatments fed as HMC (P ≥ 0.69), but the hammer mill DC diet was more digestible than the roller mill DC (P = 0.05). There was no effect on NDF digestibility, but there was a tendency for an interaction between grain type and processing method for ADF digestibility, with the roller mill DC diet having the lowest (P = 0.02) ADF digestibility and no differences (P ≥ 0.15) among the other treatments. As expected, HMC based diets had greater (P < 0.01) starch digestibility compared to DC, but milling method had no effect (P = 0.56). High moisture corn diets had greater (P = 0.01) DE intake (Mcal/kg), and hammer mill DC tended to be greater (P = 0.07) than roller mill DC. There tended (P = 0.07) to be an interaction for minimum pH, with roller mill HMC and hammer mill DC having the lowest average pH, but not different from hammer mill HMC (P ≥ 0.32). There were no differences (P = 0.56) in average pH, but HMC diets had greater variance (P = 0.04) and greater area under pH 5.6 (P = 0.05) compared to DC based diets. Feeding cattle HMC compared to DC increases nutrient digestibility but milling process had little impact.

scholarly journals RF signal calibration for improvement of 3D mapping image to locate moisture distribution in rice silo

2021 ◽  
Vol 2107 (1) ◽  
pp. 012059
Author(s):  
A A Almaleeh ◽  
A Zakaria ◽  
M H F Rahiman ◽  
Y B Abdul Rahim ◽  
L Munirah ◽  
...  
Keyword(s):  
Moisture Content ◽  
Real Time ◽  
Current Method ◽  
Moisture Distribution ◽  
Rice Grain ◽  
Tomographic Images ◽  
Grain Moisture ◽  
A New Technique ◽  
Assurance Process ◽  
Rf Signal

Abstract Grain storage is an important part of the post-harvest quality assurance process. The moisture level of the grains during storage is one of the primary problems. The current method of measuring rice grain moisture content is based on random sampling, which is relatively localised, and there is no real-time moisture content measurement available. The RF signal was used to build a new technique for detecting moisture and its presence in rice in real-time in this paper. The mapping of an RF signal, in particular, can be transformed into volumetric tomographic images that can be used to forecast moisture distribution.

Sign in / Sign up

Export Citation Format

Share Document