scholarly journals Recycled Plastic and Cork Waste for Structural Lightweight Concrete Production

2019 ◽  
Vol 11 (7) ◽  
pp. 1876 ◽  
Author(s):  
Carlos Parra ◽  
Eva M. Sánchez ◽  
Isabel Miñano ◽  
Francisco Benito ◽  
Pilar Hidalgo
Keyword(s):  
Compression Strength ◽  
High Performance ◽  
Lightweight Concrete ◽  
Chloride Ion ◽  
Total Porosity ◽  
Lightweight Aggregates ◽  
Chloride Ion Penetration ◽  
Concrete Production ◽  
Risk Areas ◽  
Strength And Durability

The use of waste materials as lightweight aggregates in concrete is highly recommended in seismic risk areas and environmentally recommended. However, reaching the strength needed for the concrete to be used structurally may be challenging. In this study four dosages were assayed: the first two-specimen had high cement content (550 and 700 kg/m3 respectively), Nanosilica, fly ash and superplasticizer. These samples were high performance, reaching a strength of 100MPa at 90 days. The other two mixtures were identical but replaced 48% of the aggregates with recycled lightweight aggregates (30% polypropylene, 18.5% cork). To estimate its strength and durability the mixtures were subjected to several tests. Compression strength, elasticity modulus, mercury intrusion porosimetry, carbonation, attack by chlorides, and penetration of water under pressure were analyzed. The compression strength and density of the lightweight mixtures were reduced 68% and 19% respectively; nonetheless, both retained valid levels for structural use (over 30MPa at 90 days). Results, such as the total porosity between 9.83% and 17.75% or the chloride ion penetration between 8.6 and 5.9mm, suggest that the durability of these concretes, including the lightweight ones, is bound to be very high thanks to a very low porosity and high resistance to chemical attacks.

scholarly journals Copper Slag of Pyroxene Composition as a Partial Replacement of Natural Aggregate for Concrete Production

Minerals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 439
Author(s):  
Sandra Filipović ◽  
Olivera Đokić ◽  
Aleksandar Radević ◽  
Dimitrije Zakić
Keyword(s):  
Chloride Ion ◽  
Copper Slag ◽  
Partial Replacement ◽  
Copper Ore ◽  
Silicon Iron ◽  
Low Resistance ◽  
Natural Aggregate ◽  
Chloride Ion Penetration ◽  
Concrete Production ◽  
Technical Properties

Copper slag, a by-product of the pyrometallurgical process used for obtaining copper from copper ore in Bor, Serbia, contains mainly silicon, iron, calcium, and aluminium oxides. Due to such properties, it is disposed of in landfills. Despite the favourable technical properties copper slag aggregates possess, such as low-water absorption (WA24 0.6%), low resistance to fragmentation (LA 10%), and low resistance to wear (MDE 4%), its use in the construction industry is still limited. The results of testing the technical properties of copper slag aggregates (CSAs) as a potential replacement for natural river aggregate (RA) are presented in this paper. The experiments included tests on three concrete mixtures with partial replacement of coarse natural aggregate with copper slag. The replacement of RA particle sizes of 8/16 mm and 16/31.5 mm with CSA in the amount of 20% + 50% and 50% + 50% resulted in an increase in the compressive strength of 12.4% and 10.5%, respectively. The increase of CSA content led to a decrease in water penetration resistance and salt-frost resistance of concrete, whereas the resistance to chloride ion penetration did not change significantly.

Permeability of Lightweight Aggregate Concrete with Mineral Admixture

2013 ◽  
Vol 857 ◽  
pp. 105-109
Author(s):  
Xiu Hua Zheng ◽  
Shu Jie Song ◽  
Yong Quan Zhang
Keyword(s):  
Pore Structure ◽  
Lightweight Concrete ◽  
Chloride Ion ◽  
Lightweight Aggregate ◽  
Total Porosity ◽  
Normal Weight ◽  
Mineral Admixture ◽  
Mineral Admixtures ◽  
Lightweight Aggregate Concrete ◽  
Aggregate Concrete

This paper presents an experimental study on the permeability and the pore structure of lightweight concrete with fly ash, zeolite powder, or silica fume, in comparison to that of normal weight aggregate concrete. The results showed that the mineral admixtures can improve the anti-permeability performance of lightweight aggregate concrete, and mixed with compound mineral admixtures further more. The resistance to chloride-ion permeability of light weight concrete was higher than that of At the same strength grade, the anti-permeability performance of lightweight aggregate concrete is better than that of normal weight aggregate concrete. The anti-permeability performance of LC40 was similar to that of C60. Mineral admixtures can obviously improve the pore structure of lightweight aggregate concrete, the total porosity reduced while the pore size decreased.

scholarly journals Effect of High-Dispersible Graphene on the Strength and Durability of Cement Mortars

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 915
Author(s):  
Xiaoqiang Qi ◽  
Sulei Zhang ◽  
Tengteng Wang ◽  
Siyao Guo ◽  
Rui Ren
Keyword(s):  
Pore Size Distribution ◽  
Pore Size ◽  
Size Distribution ◽  
Cement Mortar ◽  
Chloride Ion ◽  
Cementitious Materials ◽  
Chloride Ion Penetration ◽  
Cement Mortars ◽  
Strength And Durability ◽  
Durability Performance

Graphene’s outstanding properties make it a potential material for reinforced cementitious composites. However, its shortcomings, such as easy agglomeration and poor dispersion, severely restrict its application in cementitious materials. In this paper, a highly dispersible graphene (TiO2-RGO) with better dispersibility compared with graphene oxide (GO) is obtained through improvement of the graphene preparation method. In this study, both GO and TiO2-RGO can improve the pore size distribution of cement mortars. According to the results of the mercury intrusion porosity (MIP) test, the porosity of cement mortar mixed with GO and TiO2-RGO was reduced by 26% and 40%, respectively, relative to ordinary cement mortar specimens. However, the TiO2-RGO cement mortars showed better pore size distribution and porosity than GO cement mortars. Comparative tests on the strength and durability of ordinary cement mortars, GO cement mortars, and TiO2-RGO cement mortars were conducted, and it was found that with the same amount of TiO2-RGO and GO, the TiO2-RGO cement mortars have nearly twice the strength of GO cement mortars. In addition, it has far higher durability, such as impermeability and chloride ion penetration resistance, than GO cement mortars. These results indicate that TiO2-RGO prepared by titanium dioxide (TiO2) intercalation can better improve the strength and durability performance of cement mortars compared to GO.

Research and Applying Evolution of High Efficient Water-Reducing Agent for High Performance Concrete

2012 ◽  
Vol 610-613 ◽  
pp. 573-576
Author(s):  
Zheng Jun Wang ◽  
Jia Bin Liang
Keyword(s):  
High Performance ◽  
Lightweight Concrete ◽  
High Performance Concrete ◽  
Concrete Strength ◽  
High Strength ◽  
Reducing Agent ◽  
Mass Concrete ◽  
Green Concrete ◽  
High Efficient ◽  
Strength And Durability

This paper discusses the development of water-reducing agent and the present situation of the application of high performance concrete. The traditional concrete will be substituted by high performance concrete, green concrete. In the course of appearance of high performance and green, concrete admixtures plays an extremely important role. Concrete water-reducing agent is admixture of the main part. In the case of keeping liquidity, it can make water consumption reduce, so the concrete strength and durability can be improved. It is applicable to all kinds of industrial and civil construction engineering, and it can be applied to different strength grade of concrete. It has important significance for mass concrete engineering, marine building facilities, and component and product of high strength lightweight concrete.

Effect of Metakaolin-Based Modifier on the Permeability of Concrete Structure in the Marine Environment

2013 ◽  
Vol 438-439 ◽  
pp. 117-120
Author(s):  
Jun Tao Ma ◽  
Liang Yan ◽  
Yu Ping Tong ◽  
Hui Xian Wang
Keyword(s):  
Fly Ash ◽  
Marine Environment ◽  
Concrete Structure ◽  
Chloride Ion ◽  
Penetration Resistance ◽  
Chloride Ion Penetration ◽  
Working Performance ◽  
Electric Flux ◽  
Penetration Behavior ◽  
Strength And Durability

Corrosion of the steel reinforcement in the concrete structure caused by chloride ion penetration becomes more serious in the marine environment. Metakaolin has been widely used in the concrete structure to improve the strength and durability. The combination of metakaolin (MK) and fine fly ash (FA) was studied in the article and the penetration behavior of concrete with various contents of metakaolin-based modifier is investigated. The penetration resistance of concrete was tested in combination of electric flux test. The improving mechanism was studied with mercury intrusion porosimetry analysis (MIP). The experiment results indicate that metakaolin-based modifier improved the penetration resistance of concrete obviously. The combination of fine fly ash weakened the water sucking action of metakaolin and preserved the working performance of concrete. The pore size distribution of concrete containing metakaolin-based modifier has been optimized to improve the microstructure and enhance the penetration resistance of concrete.

scholarly journals Durability Properties of concrete incorporating calcined Phyllite

2021 ◽  
Author(s):  
DALPAT CHUNDAWAT ◽  
DINESH SHARMA ◽  
Sandeep Tomar
Keyword(s):  
Ball Mill ◽  
Laboratory Tests ◽  
Metamorphic Rock ◽  
Underground Mining ◽  
Chloride Ion ◽  
Partial Replacement ◽  
Basic Medium ◽  
Chloride Ion Penetration ◽  
Strength And Durability ◽  
Maximum Content

The environmental and economic concern is the biggest challenge that concrete industry is facing today. Advancement in utilization of wastes in concrete as a mixture reduces usage of natural resources. Phyllite is a kind of foliated metamorphic rock generates during underground mining .Phyllite was calcined at 850 to 900oC in furnace and ground in ball mill. In this study, cement was partially replaced by weight with calcined phyllite to make M30 grade of concrete with 0% (Control mix), 2%, 4%, 6%, 8%, & 10%, (which are designated as M1, M2, M3, M4, M5 and M6). The laboratory tests such as slump value, compressive strength, flexural strength, water absorption, chloride ion penetration and durability in acidic and basic medium were conducted on the phyllite concrete and results are compared with the control mix. Through results it is concluded that cement can be replaced in concrete at the tune of 8% with Calcine Phyllite (CP) without affecting the strength and durability. The aim of the experiment is to find the maximum content of mines calcined Phyllite that can be used as a partial replacement of cement without compromising the quality on any of the characteristics of concrete.

Influence of Slag Fineness on Durability of High-Performance Concrete

2012 ◽  
Vol 204-208 ◽  
pp. 3240-3243
Author(s):  
Hui Liu ◽  
Ping Li ◽  
Qiao Lan Jin
Keyword(s):  
Compressive Strength ◽  
Surface Area ◽  
Frost Resistance ◽  
High Performance ◽  
High Performance Concrete ◽  
Chloride Ion ◽  
Penetration Resistance ◽  
Concrete Durability ◽  
Chloride Ion Penetration ◽  
Ion Penetration

This research focuses on investigating the high performance concrete durability containing slag with different fineness and dosage. For this purpose, the 28-day compressive strength, chloride ion penetration, and frost resistance were investigated, with slag surface area 420m2/kg, 530m2/kg, 610m2/kg, and 720m2/kg, and replacement percentage 0%, 20%, 40%, and 60%, respectively. It was found that chloride ion penetration resistance were affected by the fineness and dosage of slag, and concrete frost resistance property was mainly controlled by dosage of slag rather than the fineness, and the 28-day compressive strength increased with slag incorporation.

Sign in / Sign up

Export Citation Format

Share Document