scholarly journals Mechanical Degradation and Thermal Decomposition of Ethylene-Vinyl Acetate (EVA) Polymer-Modified Cement Mortar (PCM) Exposed to High-Temperature

2019 ◽  
Vol 11 (2) ◽  
pp. 500 ◽  
Author(s):  
Hyung-Jun Kim ◽  
Jae-Yeon Park ◽  
Heong-Won Suh ◽  
Beom-Yeon Cho ◽  
Won-Jun Park ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Decomposition ◽  
Compressive Strength ◽  
High Temperature ◽  
Vinyl Acetate ◽  
Cement Mortar ◽  
Ethylene Vinyl Acetate ◽  
Mechanical Degradation ◽  
Rc Structures ◽  
Cement Ratio

A polymer-modified cement mortar (PCM) is widely used as a repair material for reinforced concrete (RC) structures owing to its excellent strength and durability. However, considering the maintenance of the RC structures and the use period of the structures, the change in the physical properties of the PCM should be evaluated when exposed to various high-temperature environments, such as fires. In this study, the degradation of the mechanical properties (compressive strength and modulus of elasticity), thermal decomposition of the PCM in various high-temperature environments, and the change in the pore structure of the PCM after exposure to high temperatures were quantitatively investigated. A mechanical property evaluation of PCM was performed under three heating conditions: (i) heating in a compression tester, (ii) heating the specimen in an oven to a predetermined temperature and then moving it to a compression tester preheated to the same temperature, and (iii) cooling to room temperature after heating. In the experiment, a PCM specimen was prepared by changing the polymer–cement ratio (polymer content) of ethylene-vinyl acetate (EVA), the most commonly used polymer, to perform a high-temperature sectional test from 200 to 800 °C. In addition, to investigate the change in the PCM mechanical properties in the high-temperature region, in terms of the pyrolysis of EVA, the porosity change and mass change were examined using thermal analysis and mercury intrusion porosimetry. Before heating, the compressive strength of the PCM increased with the EVA content up to 10 % of the polymer–cement ratio. Under the cooling conditions after heating up to 200 °C, the mechanical performance of the PCM was restored, whereas the degradation of the mechanical properties of the PCM without cooling was more pronounced. Furthermore, the mass loss, heat flow, and the total porosity of the PCM increased as the EVA content increased, which is correlated with the degradation of the mechanical properties of the PCM.

scholarly journals Combustion and Mechanical Properties of Polymer-Modified Cement Mortar at High Temperature

2017 ◽  
Vol 2017 ◽  
pp. 1-10 ◽  
Author(s):  
Hyung-Jun Kim ◽  
Won-Jun Park
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Temperature ◽  
Heat Release ◽  
Cement Mortar ◽  
Mass Loss Rate ◽  
Polymer Content ◽  
Cement Ratio ◽  
Combustion Properties ◽  
Polymer Type

Although polymer-modified cement mortar (PCM) has been extensively used as finishing and repairing material, it is necessary to understand its combustion properties and mechanical properties at high temperature. This study evaluated the combustion characteristics with varying experimental parameters such as polymer type, unit polymer content, polymer-cement ratio, and thickness of the specimen. This study also evaluated the compressive strength and elastic modulus of PCMs with focus on the effects of the type of polymer, unit polymer content, and polymer-cement ratio. As a result, the incombustibility of the PCM was in the following order: SBR < VVA < EVA. After heating end, the mass loss rate of the PCM was less than 30%, regardless of the polymer type, unit polymer content, and W/C. In heat release rate test, the higher the unit polymer content, the greater the total heat release, regardless of the difference in W/C. The PAE series showed excellent fire resistance in the temperature range of 200~400°C. PCMs with a unit polymer content of 5%, modified with EVA and PAE, showed outstanding compressive strength at 200~400°C. At elevated temperature, the modulus of elasticity of PCM declined with an increase in the unit polymer content, regardless of the polymer type.

scholarly journals Mechanical Properties of Concrete with Various Water-Cement Ratio After High Temperature Exposure

2019 ◽  
Vol 2 (2) ◽  
pp. 126-136
Author(s):  
M.I Retno Susilorini ◽  
Budi Eko Afrianto ◽  
Ary Suryo Wibowo
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Temperature ◽  
Modulus Of Elasticity ◽  
Building Materials ◽  
Heating Process ◽  
High Temperature Exposure ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Temperature Exposure

Concrete building safety of fire is better than other building materials such as wood, plastic, and steel,because it is incombustible and emitting no toxic fumes during high temperature exposure. However,the deterioration of concrete because of high temperature exposure will reduce the concrete strength.Mechanical properties such as compressive strength and modulus of elasticity are absolutely corruptedduring and after the heating process. This paper aims to investigate mechanical properties of concrete(especially compressive strength and modulus of elasticity) with various water-cement ratio afterconcrete suffered by high temperature exposure of 500oC.This research conducted experimental method and analytical method. The experimental methodproduced concrete specimens with specifications: (1) specimen’s dimension is 150 mm x 300 mmconcrete cylinder; (2) compressive strength design, f’c = 22.5 MPa; (3) water-cement ratio variation =0.4, 0.5, and 0.6. All specimens are cured in water for 28 days. Some specimens were heated for 1hour with high temperature of 500oC in huge furnace, and the others that become specimen-controlwere unheated. All specimens, heated and unheated, were evaluated by compressive test.Experimental data was analyzed to get compressive strength and modulus of elasticity values. Theanalytical method aims to calculate modulus of elasticity of concrete from some codes and to verifythe experimental results. The modulus elasticity of concrete is calculated by 3 expressions: (1) SNI03-2847-1992 (which is the same as ACI 318-99 section 8.5.1), (2) ACI 318-95 section 8.5.1, and (3)CEB-FIP Model Code 1990 Section 2.1.4.2.The experimental and analytical results found that: (1) The unheated specimens with water-cementratio of 0.4 have the greatest value of compressive strength, while the unheated specimens with watercementratio of 0.5 gets the greatest value of modulus of elasticity. The greatest value of compressivestrength of heated specimens provided by specimens with water-cement ratio of 0.5, while the heatedspecimens with water-cement ratio of 0.4 gets the greatest value of modulus of elasticity, (2) Allheated specimens lose their strength at high temperature of 500oC, (3) The analytical result shows thatmodulus of elasticity calculated by expression III has greater values compares to expression I and II,but there is only little difference value among those expressions, and (4)The variation of water-cementratio of 0.5 becomes the optimum value.

scholarly journals High Temperature Degradation Mechanism of Concrete with Plastering Layer

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 398
Author(s):  
Chihao Liu ◽  
Jiajian Chen
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Thermal Decomposition ◽  
Electron Microscope ◽  
High Temperature ◽  
Thermogravimetric Analysis ◽  
Degradation Mechanism ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Scanning Electron

At present, the research on the high temperature degradation of concrete usually focuses on only the degradation of concrete itself without considering the effect of the plastering layer. It is necessary to take into account the influence of the plastering layer on the high temperature degradation of concrete. With an increase in the water/cement ratio, the explosion of concrete disappeared. Although increasing the water/cement ratio can alleviate the cracking of concrete due to lower pressure, it leads to a decrease in the mechanical properties of concrete after heating. It is proved that besides the water/cement ratio, the apparent phenomena and mechanical properties of concrete at high temperature can be affected by the plastering layer. The plastering layer can relieve the high temperature cracking of concrete, and even inhibit the high temperature explosion of concrete with 0.30 water/cement ratio. By means of an XRD test, scanning electron microscope test and thermogravimetric analysis, it is found that the plastering layer can promote the rehydration of unhydrated cement particles of 0.30 water/cement ratio concrete at high temperature and then promote the mechanical properties of concrete at 400 °C. However, the plastering layer accelerated the thermal decomposition of C-S-H gel of concrete with a water/cement ratio of 0.40 at high temperature, and finally accelerate the decline of mechanical property of concrete. To conclude, the low water/cement ratio and plastering layer can delay the deterioration of concrete at high temperature.

Influence of Temperature on the Hydration Heat of Polymer Modified Mortars

2013 ◽  
Vol 687 ◽  
pp. 130-135
Author(s):  
Si Feng Liu ◽  
Si Jun Guo ◽  
Pei Ming Wang
Keyword(s):  
High Temperature ◽  
Low Temperature ◽  
Vinyl Acetate ◽  
Cement Mortar ◽  
Ethylene Vinyl Acetate ◽  
Hydration Heat ◽  
Influence Of Temperature ◽  
Influence Of Temperature On ◽  
Effects Of Temperature ◽  
Isothermal Calorimeter

The hydration heat of polymer modified mortar were measured at 5°C、10°C、20°C and 40°C using Multi-channel Isothermal calorimeter. The effects of temperature on hydration heat of polymer modified mortars with 0.1% methyl hydroxylpropyl cellulose (MHPC), 3% ethylene vinyl acetate (EVA) and 0.1%MHPC+3%EVA were investigated. The curves of hydration heat show that the polymer reduces the hydration heat of mortars and it is related to the temperature. The effects will be more and more remarkable with the increasing of temperature; Temperature also affects the exothermic rate peak of polymer modified mortars. The exothermic rate peak of polymer modified mortar at low temperature is almost equal to that of the ordinary cement mortar. However, it is obviously lower than that of ordinary cement mortar at high temperature ; The time to the exothermic rate peak of polymer modified mortar is also related to the temperature.

Performance of ilmenite concrete at sustained elevated temperatures

1988 ◽  
Vol 15 (5) ◽  
pp. 776-783
Author(s):  
H. S. Wilson
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Temperature ◽  
Flexural Strength ◽  
Key Words ◽  
Elevated Temperatures ◽  
Cement Ratio ◽  
Nondestructive Tests ◽  
High Temperature Mechanical Properties ◽  
Curing Period

Two similar mixes were made with cement contents of about 350 kg/m3 and a water–cement ratio of 0.50. The concrete specimens, moist cured for 7 days, were cured in air for 28 and 120 days, respectively, prior to heating. The exposure temperatures were 75, 150, 300, and 450 °C. The periods of exposure at each temperature were 2, 30, and 120 days.The compressive strengths, before heating, of the specimens cured for 35 and 120 days were 41.0 and 46.2 MPa, respectively, and the flexural strengths were 4.9 and 5.8 MPa. Compared with those strengths, the strengths of the specimens heated for 30 days or more increased at 75 °C but decreased at higher temperatures. The losses increased with increase in temperature, reaching about 30% at 450 °C.The flexural strength of the concrete cured in air for 28 days was more adversely affected than was the compressive strength. The flexural and compressive strengths of the concrete cured in air for 120 days were affected to about the same degree. The longer curing period had little effect on the relative losses in compressive strength, but the longer curing period reduced the loss in flexural strength. In most applications, the loss in strength could be compensated by proportioning the mix to overdesign for strength. Key words: high-density concrete, ilmenite, aggregates, high temperature, mechanical properties, nondestructive tests.

Experimental Study on the Compressive Strength of Cement Mortar

2014 ◽  
Vol 711 ◽  
pp. 422-425
Author(s):  
Yong Quan Yuan ◽  
Xue Liang Jiang ◽  
Zhong Lin Zhu ◽  
Jiang Chen
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Compressive Strength ◽  
Cement Mortar ◽  
Similar Material ◽  
Mixture Ratio ◽  
Cement Ratio ◽  
Mortar Strength ◽  
Original Rock ◽  
Rock Mechanical Properties

Cement mortar is an ideal similar material. In this paper,by using cement, sand and other materials to make the M5, M7.5, M10 three strength grades cement mortar, the effect of water cement ratio and cement dosage on the strength of cement mortar was studied. The changing rule of the cement mortar strength along with age was also analyzed.Through the test, the mortar mixture ratio that was consistent with the original rock mechanical properties was determined ultimately.

scholarly journals Mechanical Properties of Cement Mortar after Dry–Wet Cycles and High Temperature

2020 ◽  
Vol 6 (5) ◽  
pp. 1031-1038
Author(s):  
Xiong Liang-Xiao ◽  
Song Xiao-Gang
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Temperature ◽  
Cement Mortar ◽  
Peak Stress ◽  
Temperature Treatment ◽  
High Temperature Treatment ◽  
Factors Affecting ◽  
Temperature Exposure ◽  
Compressive Tests

The dry–wet cycle and high temperature exposure are important factors affecting the normal use and durability of concrete structures. The objective of this work is to investigate the mechanical properties of cement mortar specimens after combinations of dry–wet cycles and high temperature exposures, uniaxial compressive tests on cement mortar specimens were carried out under the following two sets of conditions: (1) high temperature treatment followed by a dry–wet cycle and (2) a dry–wet cycle followed by high temperature treatment. The results show that the compressive strength of specimens increases with the number of dry–wet cycles. After a dry–wet cycle and then a high temperature treatment procedure, the compressive strength of a specimen will first decrease and then increase with the number of dry–wet cycles. The strain at the peak stress of cement mortar decreases as the number of dry–wet cycles increases. At present, there are few research results about the mechanical properties of concrete first after combinations of dry–wet cycles and high temperature exposures. The work in this paper can enrich the results in this area.

scholarly journals Tests on the Mechanical Properties of Corroded Cement Mortar after High Temperature

2020 ◽  
Vol 6 (3) ◽  
pp. 459-469 ◽  
Author(s):  
Xiong Liang-Xiao ◽  
Chen Cong
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Temperature ◽  
Sodium Sulfate ◽  
Sea Water ◽  
Cement Mortar ◽  
Peak Stress ◽  
Sulfate Solution ◽  
Sodium Sulfate Solution ◽  
Compression Tests

Durability of cement mortar and concrete materials under sea water condition is always an important research topic. The objective of this work is to understand the mechanical properties of corroded cement mortar after high temperature, the cement mortar specimens after high temperature were placed in water and sodium sulfate solution, and then the uniaxial compression tests were carried out on the cement mortar specimens after corroded. Test results show that both the differences of compressive strength and strain at the peak stress after high temperature caused by high temperature, are relatively small when the specimens are eroded in water, and the differences are relatively high when the specimens are eroded in sodium sulfate solution. The compressive strength of the cement mortar specimens under normal temperature eroded in sodium sulfate solution is highest, and that eroded in water is lowest. The compressive strength of specimen after high temperature eroded in water is highest and that eroded in sodium sulfate solution is lowest. The strain at the peak stress of specimen, whether after high temperature or not, is highest when eroded in sodium sulfate solution, and that eroded in water is lowest. At present, there are few research results about the mechanical properties of concrete first after high temperature and then after sea water corrosion. The work in this paper can enrich the results in this area.

Mechanical Properties and Microstructures of Cement Mortar Modified with Styrene-Butadiene Polymer Emulsion

2010 ◽  
Vol 168-170 ◽  
pp. 190-194 ◽  
Author(s):  
Zhen Jun Wang ◽  
Rui Wang ◽  
Yu Bin Cheng
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Cement Mortar ◽  
Strength Increase ◽  
Polymer Emulsion ◽  
Cement Ratio ◽  
Cement Mortars ◽  
Water To Cement Ratio ◽  
Styrene Butadiene

In this paper, styrene-butadiene polymer emulsion SD622S was adopted to modify cement mortar; mechanical properties of cement mortars were studied and microstructures was analyzed by means of Scanning Electron Microscope (SEM) and Specific Surface Area & Pore Distribution Analyzer. The results show that in contrast to ordinary cement mortar, if water to cement ratio (W/C) is constant, compressive strength of modified cement mortar can decrease, while flexural strength and toughness, ratio of compressive strength to flexural strength, increase with the increase of polymer to cement ratio in mass (P/C) at 7 and 28 curing days. With the increase of P/C, net structure made from polymer and cement hydration products is developed and pore whose size is smaller than 200Å begins to increase, which indicates pore diameters in modified cement mortar change to be finer. So microstructures of modified cement mortar become denser and display higher toughness.

Sign in / Sign up

Export Citation Format

Share Document