scholarly journals Ultrasonic Propagation in Liquid and Ice Water Drops. Effect of Porosity

Sensors ◽  
2021 ◽  
Vol 21 (14) ◽  
pp. 4790
Author(s):  
Michiel Mendonck ◽  
Sofía Aparicio ◽  
Cristóbal González González Díaz ◽  
Margarita G. Hernández ◽  
Guillermo M. Muñoz Muñoz Caro ◽  
...  
Keyword(s):  
Ultrasonic Velocity ◽  
Liquid Drop ◽  
Micromechanical Model ◽  
Ultrasonic Pulse ◽  
Ultrasonic Waves ◽  
High Porosity ◽  
Water Drops ◽  
Ultrasonic Techniques ◽  
Ultrasonic Propagation ◽  
Ice Water

This work studies ultrasonic propagation in liquid and ice water drops. The effect of porosity on attenuation of ultrasonic waves in the drops is also explored. The motivation of this research was the possible application of ultrasonic techniques to the study of interstellar and cometary ice analogs. These ice analogs, made by vapor deposition onto a cold substrate at 10 K, can display high porosity values up to 40%. We found that the ultrasonic pulse was fully attenuated in such ice, and decided to grow ice samples by freezing a liquid drop. Several experiments were performed using liquid or frozen water drops with and without pores. An ultrasonic pulse was transmitted through each drop and measured. This method served to estimate the ultrasonic velocity of each drop by measuring drop size and time-of-flight of ultrasonic transmission. Propagation of ultrasonic waves in these drops was also simulated numerically using the SimNDT program developed by the authors. After that, the ultrasonic velocity was related with the porosity using a micromechanical model. It was found that a low value of porosity in the ice is sufficient to attenuate the ultrasonic propagation. This explains the observed lack of transmission in porous astrophysical ice analogs.

On Nondestructive Evaluation of Wood Materials Using Ultrasonic Techniques

2005 ◽  
Vol 297-300 ◽  
pp. 1973-1978
Author(s):  
In Young Yang ◽  
Kwang Hee Im ◽  
David K. Hsu ◽  
Sun Kyu Kim ◽  
Sung Jin Soug ◽  
...  
Keyword(s):  
Nondestructive Evaluation ◽  
Ultrasonic Velocity ◽  
Material Properties ◽  
Low Frequency ◽  
Ultrasonic Pulse ◽  
Data Acquisition Software ◽  
Dry Coupling ◽  
Ultrasonic Techniques ◽  
Automated Data Acquisition ◽  
Transmission Scans

In this work, a wood material was nondestructively characterized and a technique was developed to measure ultrasonic velocity in wood using automated data acquisition software. It is desirable to perform nondestructive evaluation (NDE) to assess material properties and absorption of wood because wood is a natural composite and often inhomogeneity. Several ultrasonic techniques were applied to wood for the evaluation of variations material properties. The variation of ultrasonic velocity was measured and found to be somewhat consistent with those in infiltrated area in the course of nature absorption. Low frequency (1MHz) through-transmission scans based on both amplitude and time-of-flight of the ultrasonic pulse were used for mapping out the material property inhomogeneity. These results were compared with those obtained by dry-coupling ultrasonics. A good correlation was found between ultrasonic velocity (a pulse overlap and peak-delay measurement method) and C-scan image signal based on peak-to-peak amplitude.

A MODIFIED FINITE DIFFERENCES METHOD FOR ANALYSIS OF ULTRASONIC PROPAGATION IN NONHOMOGENEOUS MEDIA

2010 ◽  
Vol 18 (01) ◽  
pp. 31-45 ◽  
Author(s):  
LUCIANO ALONSO RENTERIA ◽  
JUAN M. PEREZ ORIA
Keyword(s):  
Helmholtz Equation ◽  
Finite Differences ◽  
Computational Cost ◽  
Industrial Applications ◽  
Ultrasonic Waves ◽  
Nonhomogeneous Media ◽  
Finite Differences Method ◽  
High Gradients ◽  
Ultrasonic Propagation ◽  
Homogeneous Media

The propagation of ultrasonic waves is generally studied in homogeneous media, although in certain industrial applications the conditions of propagation differ from the ideal conditions and the predicted results are not valid. This work is focused on the resolution of the Helmholtz equation for the study of the ultrasonic propagation in nonhomogeneous media. In this way, the solution of the Helmholtz equation has been obtained by means of Finite Differences, using a nonconventional scheme that substantially improves the results obtained with other techniques such as standard Finite Differences or Finite Elements. Moreover, it decreases the computational cost in the calculation of the coefficients about 85%. The effects on the ultrasonic echoes in propagation environments with high gradients of propagation's speed have been analyzed by simulation using the method presented, and the results obtained have been experimentally validated through a set of measurements.

Classification of Iron Meteorites with High Frequency Ultrasonic Waves

2019 ◽  
Vol 24 (2) ◽  
pp. 277-284
Author(s):  
Dris El Abassi ◽  
Bouazza Faiz ◽  
Abderrahmane Ibhi ◽  
Idris Aboudaoud
Keyword(s):  
Phase Velocity ◽  
Acoustic Impedance ◽  
Nickel Content ◽  
Normal Incidence ◽  
Ultrasonic Pulse ◽  
Ultrasonic Waves ◽  
Iron Meteorites ◽  
Acoustic Transducer ◽  
Pulse Echo ◽  
Non Destructive

We present the results of an ultrasonic pulse-echo technique and its potential to classify iron meteorites into hexahedrites, octahedrites and ataxites by determining their acoustic impedance and phase velocity. Our technique has been adapted from those used in the field of ultrasonic non-destructive investigation of a variety of materials. The main advantage of our technique is that it does not need any preparation of the meteorites like cutting and etching and therefore is rapid, easy and non-destructive. In essence, a broadband acoustic transducer is used in a monostatic pulse-echo configuration which means that both the transducer and the meteorite sample are located in a water bath and adjusted in the way that the ultrasonic pulse shit the meteorite sample at normal incidence. Then the reflected pulses from the front and rear faces of the meteorite sample are measured with the emitting transducer, digitally recorded and processed to analyze the signal. After Fourier transforming the echoed pulses from the front and the rear face of the meteorite sample, the calculated reflection coefficients yield the phase velocity and the acoustic impedance. Our study investigates a variety of iron meteorites collected in Morocco and other countries and it helps to understand how the nickel content of these meteorites affects the acoustic impedance. It reveals that the acoustic impedance of iron meteorites increases with increasing nickel content, so that a further refinement of our technique might have the potential to classify iron meteorites directly and reliably into hexahedrites, octahedrites and ataxites without destroying them.

Effects of Briquettes with Different Crack Structures on Propagation Characteristics of Ultrasonic Waves under Wetting Conditions

2020 ◽  
Author(s):  
Gang Wang ◽  
Jinzhou Li ◽  
Huaixing Li ◽  
Zhiyuan Liu ◽  
Yanpei Guo ◽  
...  
Keyword(s):  
Particle Size ◽  
Ultrasonic Velocity ◽  
Bituminous Coal ◽  
Ultrasonic Attenuation ◽  
Crack Size ◽  
Ultrasonic Waves ◽  
Ultrasonic Frequency ◽  
Propagation Characteristics ◽  
Sample Mass ◽  
Velocity Increase

Abstract In order to examine the effect of briquettes with different crack structures on ultrasonic characteristics under different wetting conditions, a series of ultrasonic testing are carried out on briquettes at different wetting heights and the ultrasonic characteristics in these coal samples are explored. The results show that ultrasonic amplitude is positively correlated with the emission voltage, whereas ultrasonic frequency is negatively correlated with the emission voltage. Changes in both are closely related to the particle size and density. The ultrasonic velocity is positively correlated with the wetting degree. Sample mass has the greatest effect on the ultrasonic velocity, followed by particle size, and pressure has the smallest effect. At dry stage, ultrasonic velocity in gas coal is less than that in bituminous coal. The opposite is true in the fully wet state. The influence of crack thickness on ultrasonic velocity gradually increases with the wetting degree increasing. At dry stage, the velocity gradually increases with the crack dip increasing, while as the wetting height increasing, magnitude of velocity increase gradually decreases with the dip increasing. The ultrasonic attenuation in the briquettes reduces with the emission voltage enhancing. The attenuation decreases with sample particle size, crack thickness and crack size decreasing and with sample mass, pressure and crack dip increasing. The ultrasonic attenuation shows a trend of increase before decrease with the wetting height increasing. The attenuation of ultrasonic wave increases with wave velocity increasing for intact samples and shows a trend of increase before decrease for cracked samples.

scholarly journals High ice water content at low radar reflectivity near deep convection – Part 2: Evaluation of microphysical pathways in updraft parcel simulations

2015 ◽  
Vol 15 (20) ◽  
pp. 11729-11751 ◽  
Author(s):  
A. S. Ackerman ◽  
A. M. Fridlind ◽  
A. Grandin ◽  
F. Dezitter ◽  
M. Weber ◽  
...  
Keyword(s):  
Water Vapor ◽  
Water Content ◽  
Deep Convection ◽  
Radar Reflectivity ◽  
Doppler Velocity ◽  
Diffusional Growth ◽  
Ice Particles ◽  
Ice Water Content ◽  
Water Drops ◽  
Ice Water

Abstract. The aeronautics industry has established that a threat to aircraft is posed by atmospheric conditions of substantial ice water content (IWC) where equivalent radar reflectivity (Ze) does not exceed 20–30 dBZ and supercooled water is not present; these conditions are encountered almost exclusively in the vicinity of deep convection. Part 1 (Fridlind et al., 2015) of this two-part study presents in situ measurements of such conditions sampled by Airbus in three tropical regions, commonly near 11 km and −43 °C, and concludes that the measured ice particle size distributions are broadly consistent with past literature with profiling radar measurements of Ze and mean Doppler velocity obtained within monsoonal deep convection in one of the regions sampled. In all three regions, the Airbus measurements generally indicate variable IWC that often exceeds 2 g m-3 with relatively uniform mass median area-equivalent diameter (MMDeq) of 200–300 μm. Here we use a parcel model with size-resolved microphysics to investigate microphysical pathways that could lead to such conditions. Our simulations indicate that homogeneous freezing of water drops produces a much smaller ice MMDeq than observed, and occurs only in the absence of hydrometeor gravitational collection for the conditions considered. Development of a mass mode of ice aloft that overlaps with the measurements requires a substantial source of small ice particles at temperatures of about −10 °C or warmer, which subsequently grow from water vapor. One conceivable source in our simulation framework is Hallett–Mossop ice production; another is abundant concentrations of heterogeneous ice freezing nuclei acting together with copious shattering of water drops upon freezing. Regardless of the production mechanism, the dominant mass modal diameter of vapor-grown ice is reduced as the ice-multiplication source strength increases and as competition for water vapor increases. Both mass and modal diameter are reduced by entrainment and by increasing aerosol concentrations. Weaker updrafts lead to greater mass and larger modal diameters of vapor-grown ice, the opposite of expectations regarding lofting of larger ice particles in stronger updrafts. While stronger updrafts do loft more dense ice particles produced primarily by raindrop freezing, we find that weaker updrafts allow the warm rain process to reduce competition for diffusional growth of the less dense ice expected to persist in convective outflow.

Regimes during liquid drop impact on a liquid pool

2015 ◽  
Vol 768 ◽  
pp. 492-523 ◽  
Author(s):  
Bahni Ray ◽  
Gautam Biswas ◽  
Ashutosh Sharma
Keyword(s):  
Vortex Ring ◽  
Liquid Drop ◽  
Liquid Pool ◽  
Ring Formation ◽  
Gas Bubble ◽  
Jet Formation ◽  
Vortex Ring Formation ◽  
Water Drops ◽  
Regime Map ◽  
The Impact

Water drops falling on a deep pool can either coalesce to form a vortex ring or splash, depending on the impact conditions. The transition between coalescence and splashing proceeds via a number of intermediate steps, such as thick and thin jet formation and gas-bubble entrapment. We perform simulations to determine the conditions under which bubble entrapment and jet formation occur. A regime map is established for Weber numbers ranging from 50 to 300 and Froude numbers from 25 to 600. Vortex ring formation is seen for all of the regimes; it is greater for the coalescence regime and less in the case of the thin jet regime.

Dual-energy wave subtraction imaging for evaluation of barely visible impact damage with an ultrasonic propagation imaging system

2017 ◽  
Vol 29 (17) ◽  
pp. 3411-3425 ◽  
Author(s):  
Yunshil Choi ◽  
Jung-Ryul Lee
Keyword(s):  
Laser Beam ◽  
Nondestructive Evaluation ◽  
Composite Structures ◽  
Imaging System ◽  
Impact Damage ◽  
Dual Energy ◽  
Ultrasonic Waves ◽  
Excitation Energies ◽  
Ultrasonic Signals ◽  
Ultrasonic Propagation

Barely visible impact damage from low-velocity impacts have been studied as critical design factors of composite structures. In this article, a dual-energy wave subtraction algorithm using an ultrasonic propagation imaging system is proposed to evaluate barely visible impact damage as a strategy of fast in situ nondestructive evaluation or structural health monitoring (SHM). The ultrasonic propagation imaging system is a type of nondestructive evaluation or SHM system and is based on scanning laser-induced guided ultrasound and fixed sensors. The amplitude of ultrasonic signals generated by the ultrasonic propagation imaging system increases with the increasing energy of the laser beam. Two ultrasonic signals generated by different excitation energies of the laser beam can be equalized by multiplying a constant factor to one of them. Therefore, the residuals after subtraction of two signals may be close to zero. However, the two different energy induced signals in the damaged area will be nonzero due to the change in material conditions regarding the laser ultrasonic generation mechanism. The dual-energy wave subtraction algorithm eliminates most of the incident ultrasonic waves and amplifies anomalous waves. A composite wing skin including two barely visible impact damages as well as a composite sandwich panel, including a single barely visible impact damage, were inspected to validate the proposed algorithm.

scholarly journals Correlation between Laser-Ultrasound and Microstructural Properties of Laser Melting Deposited Ti6Al4V/B4C Composites

Metals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1951
Author(s):  
Wanwei Xu ◽  
Xue Bai ◽  
Zhonggang Sun ◽  
Xin Meng ◽  
Zhongming Guo
Keyword(s):  
Ultrasonic Velocity ◽  
Crystallographic Orientation ◽  
Orientation Distribution ◽  
Ultrasonic Waves ◽  
Microstructural Properties ◽  
Laser Melting ◽  
Distribution Width ◽  
Spectral Centroid ◽  
Α Phase ◽  
Centroid Frequency

The presence of large microtextured clusters (MTC) composed of small α-phase crystallites with preferred crystallographic orientations in 3D printed near-α titanium alloys leads to poor mechanical and fatigue properties. It is therefore crucial to characterize the size of MTCs nondestructively. Ti6Al4V/B4C composite materials are manufactured using Laser Melting Deposition (LMD) technology by adding an amount of nano-sized B4C particles to the original Ti6Al4V powder. TiB and TiC reinforcements precipitating at grain boundaries stimulate the elongated α crystallites and coarse columnar MTCs to equiaxed transition, and microstructures composed of approximately equiaxed MTCs with different mean sizes of 11–50 μm are obtained. Theoretical models for scattering-induced attenuation and centroid frequency downshift of ultrasonic waves propagating in such a polycrystalline medium are presented. It is indicated that, the studied composite material has an extremely narrow crystallographic orientation distribution width, i.e., a strong degree of anisotropy in MTCs. Therefore, MTCs make a dominant contribution to the total scattering-induced attenuation and spectral centroid frequency downshift, while the contribution of fine α-phase crystallites is insignificant. Laser ultrasonic inspection is performed, and the correlation between laser-generated ultrasonic wave properties and microstructural properties of the Ti6Al4V/B4C composites is analyzed. Results have shown that the deviation between the experimentally measured ultrasonic velocity and the theoretical result determined by the Voigt-averaged velocity in each crystallite is no more than 2.23%, which is in good agreement with the degree of macroscopically anisotropy in the composite specimens. The ultrasonic velocity seems to be insensitive to the size of MTCs, while the spectral centroid frequency downshift is approximately linear to the mean size of MTCs with a goodness-of-fit (R2) up to 0.99. Actually, for a macroscopically untextured near-α titanium alloy with a relatively narrow crystallographic orientation distribution, the ultrasonic velocity is not correlated with the properties of MTCs, by contrast, the central frequency downshift is dominated by the size and morphology of MTCs, showing great potentials in grain size evaluation.

scholarly journals The relationship between the compressive strength and ultrasonic pulse velocity concrete with fibers exposed to high temperatures

2018 ◽  
Vol 3 (1) ◽  
pp. 31
Author(s):  
Belaribi Hassiba ◽  
Mellas Mekki ◽  
Rahmani Fraid
Keyword(s):  
Compressive Strength ◽  
Ultrasonic Velocity ◽  
High Temperatures ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Cement Ratio ◽  
Compressive Strength Of Concrete ◽  
The Relationship ◽  
The Waves

The paper analyses the effects of high temperatures on the concrete residual strength using ultrasonic velocity (UPV). An experimental investigation was conducted to study the relationship between UPV residual data and compressive strength of concrete with different mixture proportions, cubic specimens with water-cement ratio of 0.35. They were heated in an electric furnace at temperatures ranging from 200°C to 600°C. In this experiment a comparison was made between the four groups which include two types of fibers steel 0,19%, 0,25% and 0,5%, polypropylene: 0,05%, 0,11% 0,16 % by volume. Cube specimens were tested in order to determine ultrasonic velocity. The compressive strength was tested too. According to the results, relations were established between ultrasonic velocity in the specimens and the compressive strength at different temperature and the range of the velocity of the waves were also determined for this kind of concrete. Result of the test showed that UPV test can be successfully used in order to verify the consistency of structures damaged by fire.

Sign in / Sign up

Export Citation Format

Share Document