scholarly journals RF Transceiver for the Multi-Mode Radar Applications

Sensors ◽  
2021 ◽  
Vol 21 (5) ◽  
pp. 1563
Author(s):  
Jae Kwon Ha ◽  
Chang Kyun Noh ◽  
Jin Seop Lee ◽  
Ho Jin Kang ◽  
Yu Min Kim ◽  
...  
Keyword(s):  
Long Range ◽  
Integrated Circuit ◽  
Flicker Noise ◽  
Noise Figure ◽  
Supply Voltage ◽  
Doppler Frequency ◽  
Cmos Process ◽  
Rf Transceiver ◽  
Dc Offset ◽  
Multi Mode

In this work, a multi-mode radar transceiver supporting pulse, FMCW and CW modes was designed as an integrated circuit. The radars mainly detect the targets move by using the Doppler frequency which is significantly affected by flicker noise of the receiver from several Hz to several kHz. Due to this flicker noise, the long-range detection performance of the radars is greatly reduced, and the accuracy of range to the target and velocity is also deteriorated. Therefore, we propose a transmitter that suppresses LO leakage in consideration of long-range detection, target distance, velocity, and noise figure. We also propose a receiver structure that suppresses DC offset due to image signal and LO leakage. The design was conducted with TSMC 65 nm CMOS process, and the designed and fabricated circuit consumes a current of 265 mA at 1.2 V supply voltage. The proposed transmitter confirms the LO leakage suppression of 37 dB at 24 GHz. The proposed receiver improves the noise figure by about 20 dB at 100 Hz by applying a double conversion architecture and an image rejection, and it illustrates a DC rejection of 30 dB. Afterwards, the operation of the pulse, FMCW, and CW modes of the designed radar in integrated circuit was confirmed through experiment using a test PCB.

CMOS EVEN HARMONIC SWITCHING MIXER FOR DIRECT CONVERSION RECEIVERS

2006 ◽  
Vol 15 (02) ◽  
pp. 183-196 ◽  
Author(s):  
J. J. LIU ◽  
M. A. DO ◽  
X. P. YU ◽  
K. S. YEO ◽  
S. JIANG ◽  
...  
Keyword(s):  
Power Consumption ◽  
Flicker Noise ◽  
Noise Figure ◽  
Direct Conversion ◽  
Cmos Process ◽  
Dc Offset ◽  
Direct Conversion Receivers ◽  
Dc Power ◽  
Mixer Design ◽  
Cmos Mixer

DC offset and high flicker noise are the main problems for the direct conversion CMOS mixer design. A novel even harmonic switching mixer implemented in a standard 0.18 μm CMOS process for applications in 2.45 GHz direct conversion receivers is proposed. The mixer circuit overcomes the problems of DC offset and high flicker noise. It achieves -8.24 dB gain, 5.2 dB DSB noise figure at 100 KHz, 17.25 dBm IIP3 and zero DC power consumption.

scholarly journals Design Strategies and Architectures for Ultra-Low-Voltage Delta-Sigma ADCs

Electronics ◽  
2021 ◽  
Vol 10 (10) ◽  
pp. 1156
Author(s):  
Lorenzo Benvenuti ◽  
Alessandro Catania ◽  
Giuseppe Manfredini ◽  
Andrea Ria ◽  
Massimo Piotto ◽  
...  
Keyword(s):  
Low Voltage ◽  
Flicker Noise ◽  
Supply Voltage ◽  
Cmos Process ◽  
Clock Frequency ◽  
Design Environment ◽  
Ultra Low Power ◽  
Analog Cmos ◽  
Gain Error ◽  
Dc Gain

The design of ultra-low voltage analog CMOS integrated circuits requires ad hoc solutions to counteract the severe limitations introduced by the reduced voltage headroom. A popular approach is represented by inverter-based topologies, which however may suffer from reduced finite DC gain, thus limiting the accuracy and the resolutions of pivotal circuits like analog-to-digital converters. In this work, we discuss the effects of finite DC gain on ultra-low voltage ΔΣ modulators, focusing on the converter gain error. We propose an ultra-low voltage, ultra-low power, inverter-based ΔΣ modulator with reduced finite-DC-gain sensitivity. The modulator employs a two-stage, high DC-gain, switched-capacitor integrator that applies a correlated double sampling technique for offset cancellation and flicker noise reduction; it also makes use of an amplifier that implements a novel common-mode stabilization loop. The modulator was designed with the UMC 0.18 μm CMOS process to operate with a supply voltage of 0.3 V. It was validated by means of electrical simulations using the CadenceTM design environment. The achieved SNDR was 73 dB, with a bandwidth of 640 Hz, and a clock frequency of 164 kHz, consuming only 200.5 nW. It achieves a Schreier Figure of Merit of 168.1 dB. The proposed modulator is also able to work with lower supply voltages down to 0.15 V with the same resolution and a lower power consumption despite of a lower bandwidth. These characteristics make this design very appealing in sensor interfaces powered by energy harvesting sources.

Research and Analysis of Tunable Differential N-Path Band-Pass Filter

2020 ◽  
pp. 2150055
Author(s):  
Shuxiang Song ◽  
Guolun Liu ◽  
Mingcan Cen ◽  
Chaobo Cai
Keyword(s):  
Bandpass Filter ◽  
Noise Figure ◽  
Supply Voltage ◽  
Impedance Matching ◽  
Transmission Function ◽  
Center Frequency ◽  
Cmos Process ◽  
Band Pass Filter ◽  
Pass Filter ◽  
Circuit Structure

Traditional filters usually have low Q and gain values and it is difficult to adjust their center frequencies. Moreover, it is very complicated to analyze their transmission charateristics through conventional methods. Therefore, in this paper, a tunable differential N-path bandpass filter that uses a new adjoint network method to analyze the transmission characteristics of the differential N-path structure is proposed. The filter circuit adopts a novel circuit structure consisting of two differential N-path structures, two transconductance amplifiers and an off-chip transformer. The differential structure eliminates even harmonics, the transconductance amplifier increases the circuit gain and the off-chip transformer acts as a balun, improving the filter’s Q value and achieving impedance matching. Unlike the traditional switching capacitance method used for analyzing the differential circuit structure, the method proposed in this paper does not involve complicated calculus operations. In fact, the method greatly simplifies these complex operations, and the transmission function of the circuit can be obtained through simple algebraic operations. The proposed filter was designed using TSMC 180[Formula: see text]nm CMOS process. Simulation results for a differential four-path bandpass filter formed under 1.2[Formula: see text]V supply voltage show that the gain of the filter is greater than 8.5 dB, the center frequency can be adjusted from 0.1[Formula: see text]GHz to 1[Formula: see text]GHz, the in-band insertion loss S11 is greater than 10 dB, the out-of-band IIP3 is greater than 10 dBm, the out-of-band rejection is 28 dB and the noise figure is less than 2.2 dB at [Formula: see text][Formula: see text]MHz.

scholarly journals A Linearity Improvement Front End with Subharmonic Current Commutating Passive Mixer for 2.4 GHz Direct Conversion Receiver in 0.13 μm CMOS Technology

Electronics ◽  
2020 ◽  
Vol 9 (9) ◽  
pp. 1369
Author(s):  
Dongquan Huo ◽  
Luhong Mao ◽  
Liji Wu ◽  
Xiangmin Zhang
Keyword(s):  
Power Consumption ◽  
Flicker Noise ◽  
Analytical Formula ◽  
Direct Conversion ◽  
Low Noise ◽  
Cmos Process ◽  
Passive Mixer ◽  
Dc Offset ◽  
Front End ◽  
Rf Front End

Direct conversion receiver (DCR) architecture is a promising candidate in the radio frequency (RF) front end because of its low power consumption, low cost and ease of integration. However, flicker noise and direct current (DC) offset are large issues. Owing to the local oscillator (LO) frequency, which is half of the RF frequency, and the absence of a DC bias current that introduces no flicker noise, the subharmonic passive mixer (SHPM) core topology front end overcomes the shortcoming effectively. When more and more receivers (RX) and transmitters (TX) are integrated into one chip, the linearity of the receiver front end becomes a very important performer that handles the TX and RX feedthrough. Another reason for the requirement of good linearity is the massive electromagnetic interference that exists in the atmosphere. This paper presents a linearity-improved RF front end with a feedforward body bias (FBB) subharmonic mixer core topology that satisfies modern RF front end demands. A novel complementary derivative superposition (DS) method is presented in low noise amplifier (LNA) design to cancel both the third- and second-order nonlinearities. To the best knowledge of the authors, this is the first time FBB technology is used in the SHPM core to improve linearity. A Volterra series is introduced to provide an analytical formula for the FBB of the SHPM core. The design was fabricated in a 0.13 μm complementary metal oxide semiconductor (CMOS) process with a chip area of 750 μm × 1270 μm. At a 2.4 GHz working frequency, the measurement result shows a conversion gain of 36 dB, double side band (DSB) noise figure (NF) of 6.8 dB, third-order intermodulation intercept point (IIP3) of 2 dBm, LO–RF isolation of 90 dB and 0.8 mW DC offset with 14.4 mW power consumption at 1.2 V supply voltage. These results exhibit better LO–RF feedthrough and DC offset, good gain and NF, moderate IIP3 and the highest figure of merit compared to the state-of-the-art publications.

scholarly journals Design and Simulation Study of Active Baluns Circuits for WiMAX Applications

2019 ◽  
Vol 7 (1) ◽  
Author(s):  
Frederick Ray I. Gomez ◽  
John Richard E. Hizon ◽  
Maria Theresa G. De Leon
Keyword(s):  
Phase Difference ◽  
Simulation Study ◽  
Noise Figure ◽  
Supply Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Common Source ◽  
Cmos Process ◽  
Common Gate ◽  
Active Balun

The paper presents a design and simulation study of three active balun circuits implemented in a standard 90nm Complementary Metal-Oxide Semiconductor (CMOS) process namely: (1) common-source/drain active balun; (2) common-gate with common-source active balun; and (3) differential active balun.  The active balun designs are intended for Worldwide Interoperability for Microwave Access (WiMAX) applications operating at frequency 5.8GHz and with supply voltage of 1V.  Measurements are taken for parameters such as gain difference, phase difference, and noise figure.  All designs achieved gain difference of less than 0.23dB, phase difference of 180° ± 7.1°, and noise figure of 7.2–9.85dB, which are comparable to previous designs and researches.  Low power consumption attained at the most 4.45mW.

scholarly journals GaN low-noise X-band MMIC amplifier.

2021 ◽  
Vol 2021 (2) ◽  
Author(s):  
E. Kudabay ◽  
◽  
A. Salikh ◽  
V.A. Moseichuk ◽  
A. Krivtsun ◽  
...  
Keyword(s):  
Output Power ◽  
Integrated Circuit ◽  
Noise Figure ◽  
Supply Voltage ◽  
High Electron Mobility Transistor ◽  
Low Noise ◽  
Common Source ◽  
High Electron ◽  
Monolithic Integrated Circuit ◽  
X Band

The purpose of this paper is to design a microwave monolithic integrated circuit (MMIC) for low noise amplifier (LNA) X-band (7-12 GHz) based on technology of gallium nitride (GaN) high electron mobility transistor (HEMT) with a T-gate, which has 100 nm width, on a silicon (Si) semi-insulating substrate of the OMMIC company. The amplifier is based on common-source transistors with series feedback, which was formed by high-impedance transmission line, and with parallel feedback to match noise figure and power gain. The key characteristics of an LNA are noise figure and gain. However, in this paper, it was decided to design the LNA, which should have a good margin in terms of input and output power. As a result, GaN technology was chosen, which has a higher noise figure compared to other technologies, but eliminates the need for an input power limiter, which in turn significantly increases the overall noise figure. As a result LNA MMIC was developed with the following characteristics: noise figure less than 1.6 dB, small-signal gain more than 20 dB, return loss better than -13 dB and output power more than 19 dBm with 1 dB compression in the range from 7 to 12 GHz in dimensions 2x1.5 mm², which has a supply voltage of 8 V and a current consumption of less than 70 mA. However, it should be said that LNA was only modeled in the AWR DE.

The Design and Modeling of 30 GHz Microwave Front-End

2012 ◽  
pp. 205-238
Author(s):  
Wan Yeen Ng ◽  
Xhiang Rhung Ng
Keyword(s):  
Millimeter Wave ◽  
Integrated Circuit ◽  
Noise Figure ◽  
Supply Voltage ◽  
Low Noise ◽  
Operating Frequency ◽  
Total Power ◽  
Automotive Radar ◽  
Gain Compression ◽  
Noise Amplifier

This chapter aims to discuss a millimeter wave integrated circuit (MMWIC) in frequency of 30 GHz especially switch (SPDT), medium power amplifier (MPA) and low noise amplifier (LNA). The switch is developed using a commercial 0.15 µm GaAs pHEMT technology. It achieves low loss and high isolation for millimeter wave applications. The circuit and layout drawing of SPDT switch are done by using Advanced Design System (ADS) software. The layout is verified by running the Design Rules Check (DRC) to check and clear all the errors. At the operating frequency of 30 GHz, the reported SPDT switch has 1.470 dB insertion loss and 37.455 dB of isolation. It also demonstrates 26.00 dBm of input P1dB gain compression point (P1dB) and 22.975 dBm of output P1dB. At a supply voltage of 3.0 V and 30 GHz operating frequency, this two-stage LNA achieves an associated gain of 21.628 dB, noise figure (NF) of 2.509 dB and output referred 1-dB compression point (P1dB) of -11.0 dBm, the total power consumptions for the LNA is 174 mW. At a supply voltage of 6.0 V and 30 GHz operating frequency, a 2-stage MPA achieves a linear gain (S21) of 13.236 dB, P1dB of 22.5 dBm, power gain of 11.055 dB and the PAE of 14.606%. The total power consumption for the MPA is 1.122 W. The 30 GHz LNA and PA can be applied in direct broadcast satellite (DBS), automotive radar transmitter and receiver.

Optimized Design of Low Power Complementary Metal Oxide Semiconductor Low Noise Amplifier for Zigbee Application

2021 ◽  
Vol 18 (4) ◽  
pp. 1327-1330
Author(s):  
S. Manjula ◽  
R. Karthikeyan ◽  
S. Karthick ◽  
N. Logesh ◽  
M. Logeshkumar
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Supply Voltage ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Oxide Semiconductor ◽  
Design System ◽  
Cmos Process ◽  
Design Specifications ◽  
Noise Amplifier

An optimized high gain low power low noise amplifier (LNA) is presented using 90 nm CMOS process at 2.4 GHz frequency for Zigbee applications. For achieving desired design specifications, the LNA is optimized by particle swarm optimization (PSO). The PSO is successfully implemented for optimizing noise figure (NF) when satisfying all the design specifications such as gain, power dissipation, linearity and stability. PSO algorithm is developed in MATLAB to optimize the LNA parameters. The LNA with optimized parameters is simulated using Advanced Design System (ADS) Simulator. The LNA with optimized parameters produces 21.470 dB of voltage gain, 1.031 dB of noise figure at 1.02 mW power consumption with 1.2 V supply voltage. The comparison of designed LNA with and without PSO proves that the optimization improves the LNA results while satisfying all the design constraints.

A FULLY INTEGRATED MULTIBAND CMOS 0.35 μM LNA FOR IEEE802.16 STANDARD

2013 ◽  
Vol 22 (02) ◽  
pp. 1250088 ◽  
Author(s):  
MERIAM BEN AMOR ◽  
MOURAD LOULOU ◽  
SEBASTIEN QUINTANEL ◽  
DANIEL PASQUET
Keyword(s):  
Noise Figure ◽  
Supply Voltage ◽  
Wide Band ◽  
Low Noise ◽  
Cmos Process ◽  
Frequency Range ◽  
Fully Integrated ◽  
Input Matching ◽  
Noise Amplifier ◽  
Chebyshev Filter

In this paper we present the design of a fully integrated low noise amplifier for WiMAX standard with AMS 0.35 μm CMOS process. This LNA is designed to cover the frequency range for licensed and unlicensed bands of the WiMAX 2.3–5.9 GHz. The proposed amplifier achieves a wide band input and output matching with S11 and S22 lower than -10 dB, a flat gain of 12 dB and a noise figure around 3.5 dB for the entire band and from the upper to the higher frequencies. The presented wide band LNA employs a Chebyshev filter for input matching and an inductive shunt feedback for output matching with a bias current of 15 mA and a supply voltage of 2.5 V.

scholarly journals A Low-Noise, High-Gain, and Small-Size UWB Mixer Utilizing Negative Impedance Technique and Source Input Method

Electronics ◽  
2021 ◽  
Vol 10 (21) ◽  
pp. 2655
Author(s):  
Zhaokun Zhou ◽  
Xiaoran Li ◽  
Xinghua Wang ◽  
Wei Gu
Keyword(s):  
Flicker Noise ◽  
Noise Figure ◽  
Supply Voltage ◽  
High Gain ◽  
Low Noise ◽  
Ultra Wideband ◽  
Conversion Gain ◽  
Chip Area ◽  
Input Method ◽  
Impedance Technique

This paper presents an ultra-wideband (UWB) down-conversion mixer with low-noise, high-gain and small-size. The negative impedance technique and source input method are applied for the proposed mixer. The negative impedance achieves the dynamic current injection and increases the mixer output impedance, which reduces the mixer flicker noise and increases its conversion gain. The source input method allows the input matching networks to be cancelled, avoiding the noise and loss introduced by the matching resistors, saving the chip area occupied by the matching inductors. The proposed mixer is designed in 45-nm SOI process provided by GlobalFoundries. The simulation results show a conversion gain of 11.4–14.3 dB, ranging from 3.1 to 10.6 GHz, a minimum noise figure of 9.8 dB, a RF port return loss of less than −11 dB, a port-to-port isolation of better than −48 dB, and a core chip area of 0.16 × 0.16 mm2. The power consumption from a 1 V supply voltage is 2.85 mW.

Sign in / Sign up

Export Citation Format

Share Document