scholarly journals Crack Protective Layered Architecture of Lead-Free Piezoelectric Energy Harvester in Bistable Configuration

Sensors ◽  
2020 ◽  
Vol 20 (20) ◽  
pp. 5808
Author(s):  
Ondrej Rubes ◽  
Zdenek Machu ◽  
Oldrich Sevecek ◽  
Zdenek Hadas
Keyword(s):  
Energy Harvester ◽  
Lead Free ◽  
Vibration Energy Harvester ◽  
Ultra Low Power ◽  
Energy Harvesters ◽  
Layered Architecture ◽  
Piezoelectric Energy ◽  
Wide Range ◽  
Ultra Low Power Devices ◽  
Novel Design

Kinetic piezoelectric energy harvesters are used to power up ultra-low power devices without batteries as an alternative and eco-friendly source of energy. This paper deals with a novel design of a lead-free multilayer energy harvester based on BaTiO3 ceramics. This material is very brittle and might be cracked in small amplitudes of oscillations. However, the main aim of our development is the design of a crack protective layered architecture that protects an energy harvesting device in very high amplitudes of oscillations. This architecture is described and optimized for chosen geometry and the resulted one degree of freedom coupled electromechanical model is derived. This model could be used in bistable configuration and the model is extended about the nonlinear stiffness produced by auxiliary magnets. The complex bistable vibration energy harvester is simulated to predict operation in a wide range of frequency excitation. It should demonstrate typical operation of designed beam and a stress intensity factor was calculated for layers. The whole system, without presence of cracks, was simulated with an excitation acceleration of amplitude up to 1g. The maximal obtained power was around 2 mW at the frequency around 40 Hz with a maximal tip displacement 7.5 mm. The maximal operating amplitude of this novel design was calculated around 10 mm which is 10-times higher than without protective layers.

On Mathematical Modeling of Piezoelectric Energy Harvesters

2014 ◽  
Vol 953-954 ◽  
pp. 655-658 ◽  
Author(s):  
Guang Qing Shang ◽  
Hong Bing Wang ◽  
Chun Hua Sun
Keyword(s):  
Mathematical Modeling ◽  
Energy Harvesting ◽  
Energy Harvester ◽  
Vibration Energy ◽  
Piezoelectric Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Energy Harvesting System ◽  
Piezoelectric Vibration

Energy harvesting system has become one of important areas of ​​research and develops rapidly. How to improve the performance of the piezoelectric vibration energy harvester is a key issue in engineering applications. There are many literature on piezoelectric energy harvesting. The paper places focus on summarizing these literature of mathematical modeling of piezoelectric energy harvesting, ranging from the linear to nonlinear, from early a single mechanical degree to piezoaeroelastic problems.

Heartbeat Energy Harvesting Using the Fan-Folded Piezoelectric Beam Geometry

2015 ◽  
Author(s):  
M. H. Ansari ◽  
M. Amin Karami
Keyword(s):  
Natural Frequency ◽  
Energy Harvester ◽  
Low Frequency ◽  
Mode Shapes ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Mechanical Coupling ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Piezoelectric Beam

A three dimensional piezoelectric vibration energy harvester is designed to generate electricity from heartbeat vibrations. The device consists of several bimorph piezoelectric beams stacked on top of each other. These horizontal bimorph beams are connected to each other by rigid vertical beams making a fan-folded geometry. One end of the design is clamped and the other end is free. One major problem in micro-scale piezoelectric energy harvesters is their high natural frequency. The same challenge is faced in development of a compact vibration energy harvester for the low frequency heartbeat vibrations. One way to decrease the natural frequency is to increase the length of the bimorph beam. This approach is not usually practical due to size limitations. By utilizing the fan-folded geometry, the natural frequency is decreased while the size constraints are observed. The required size limit of the energy harvester is 1 cm by 1 cm by 1 cm. In this paper, the natural frequencies and mode shapes of fan-folded energy harvesters are analytically derived. The electro-mechanical coupling has been included in the model for the piezoelectric beam. The design criteria for the device are discussed.

A Patternless Piezoelectric Energy Harvester for Ultra Low Frequency Applications

2020 ◽  
Vol 12 (7) ◽  
Author(s):  
M. R. Awal ◽  
◽  
M. Jusoh ◽  
T. Sabapathy ◽  
R. B. Ahmad ◽  
...  
Keyword(s):  
Energy Harvester ◽  
Low Frequency ◽  
Vibration Energy ◽  
Induced Voltage ◽  
Vibration Energy Harvester ◽  
Ultra Low Power ◽  
Energy Applications ◽  
Piezoelectric Energy ◽  
Deposition Thickness ◽  
Piezoelectric Harvester

This paper presents a pattern less piezoelectric harvester for ultra low power energy applications. Usually patterned cantilevers are used as vibration energy harvester which results additional fabrication process. Hence, to reduce the process, a four layer cantilever configuration is used to design the harvester with Aluminum, Silicon and Zinc Oxide. The device dimension is settled to 12×10×≈0.5009 mm3 with ≈300 nm deposition thickness for each layer. The modeling and fabrication processes are demonstrated in detail. The induced voltage by the cantilever is obtained through the analytical and practical measurements. From the measurements, it is found that, the maximum induced voltage is 91.2 mV from practical measurement with voltage density of 1.517 mV/mm3. It is evident from the results that, this pattern less model can be useful for next generation vibration energy harvester with simpler technology.

scholarly journals The Effect of Axial Displacement of Magnets in Piezoelectric Energy Harvester

2018 ◽  
Vol 7 (3.7) ◽  
pp. 95
Author(s):  
Li Wah Thong ◽  
Yu Jing Bong ◽  
Swee Leong Kok ◽  
Roszaidi Ramlan
Keyword(s):  
Frequency Spectrum ◽  
Power Output ◽  
Energy Harvester ◽  
Vibrational Energy ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Operational Frequency ◽  
And Performance

The utilization of vibration energy harvesters as a substitute to batteries in wireless sensors has shown prominent interest in the literature. Various approaches have been adapted in the energy harvesters to competently harvest vibrational energy over a wider spectrum of frequencies with optimize power output.   A typical bistable piezoelectric energy harvester, where the influence of magnetic field is induced into a linear piezoelectric cantilever, is designed and analyzed in this paper. The exploitations of the magnetic force specifically creates nonlinear response and bistability in the energy harvester that extends the operational frequency spectrum for optimize performance.  Further analysis on the effects of axial spacing displacement between two repulsive magnets of the harvester, in terms of x-axis (horizontal) and z-axis (vertical) on its natural resonant frequency and performance based on the frequency response curve are investigated for realizing optimal power output. Experimental results show that by selecting the optimal axial spacing displacement, the vibration energy harvester can be designed to produce maximized output power in an improved broadband of frequency spectrum.  

PZT Piezoelectric Energy Harvester Enhancement Using Slotted Aluminium Beam

2014 ◽  
Vol 1051 ◽  
pp. 932-936
Author(s):  
Mun Heng Lam ◽  
Hanim Salleh
Keyword(s):  
Energy Source ◽  
Renewable Energy Source ◽  
Lead Zirconate Titanate ◽  
Output Voltage ◽  
Energy Harvester ◽  
Lead Zirconate ◽  
External Beam ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Wide Range

This paper presents work on improving piezoelectric energy harvesters. Harvesting energy from vibrations has received massive attention due to it being a renewable energy source that has a wide range of applications. Over the years of development, there is always research to further improve and optimise piezoelectric energy harvesters. For this paper, the piezoelectric specimen is made of PZT (Lead Zirconate Titanate), brass reinforced and has 31.8mm length, 12.7mm width and 0.511mm thick. An external beam is implemented to provide deflection amplification which in turn increases the output of the energy harvester. Depending on the configuration of the external beam, it can amplify output voltage from 100% to 300%.

Modeling of electromechanical response and fracture resistance of multilayer piezoelectric energy harvester with residual stresses

2020 ◽  
Vol 31 (19) ◽  
pp. 2261-2287
Author(s):  
Zdeněk Machů ◽  
Oldřich Ševeček ◽  
Zdeněk Hadaš ◽  
Michal Kotoul
Keyword(s):  
Fracture Toughness ◽  
Residual Stresses ◽  
Fracture Resistance ◽  
Energy Harvester ◽  
Beam Theory ◽  
Vibration Energy Harvester ◽  
Layered Architecture ◽  
Thermal Residual Stresses ◽  
Apparent Fracture Toughness ◽  
Piezoelectric Energy

The article focuses on a modeling and subsequent optimization of a novel layered architecture of the vibration piezoceramic energy harvester composed of ZrO2/Al2O3/BaTiO3 layers and containing thermal residual stresses. The developed analytical/numerical model allows to determine the complete electromechanical response and the apparent fracture toughness of the multilayer vibration energy harvester, upon consideration of thermal residual stresses and time-harmonic kinematic excitation. The derived model uses the Euler–Bernoulli beam theory, Hamilton’s variational principle, and a classical laminate theory to determine the first natural frequency, steady-state electromechanical response of the beam upon harmonic vibrations, and also the mechanical stresses within particular layers of the harvester. The laminate apparent fracture toughness is computed by means of the weight function approach. A crucial point is the further optimization of the layered architecture from both the electromechanical response and the fracture resistance point of view. Maximal allowable excitation acceleration of the harvester upon which the piezoelectric layer will not fail is determined. It makes possible to better use the harvester’s capabilities in a given application and simultaneously guarantee its safe operation. Outputs of the derived analytical model were validated with finite element method simulations and available experimental results, and a good agreement between all approaches was obtained.

Structural Modification Strategies to Improve Piezoelectric Energy Harvester Performance

2015 ◽  
Vol 752-753 ◽  
pp. 934-940 ◽  
Author(s):  
Hanim Salleh ◽  
Mun Heng Lam ◽  
Linasuriani Muhamad ◽  
Mohd Firdaus bin Jaafar
Keyword(s):  
Power Density ◽  
Structural Modification ◽  
Energy Harvester ◽  
General Structure ◽  
Specific Power ◽  
Rubber Layer ◽  
Energy Harvesters ◽  
Similar Work ◽  
Piezoelectric Energy ◽  
Wide Range

Harvesting energy from vibrations has received massive attention due to it being a renewable energy source that has a wide range of applications. Over the years of development, there is always research to further improve and optimise piezoelectric energy harvesters. This paper presents work on improving piezoelectric energy harvesters based on the structural modifications. Four different strategies of structural modification are employed for optimization by using additional beam structure as well as incorporation of rubber layer. This work summarized the optimum performance of the strategies at a resonance frequency of 60 + 2 Hz at 0.25g. The parameters compared among the strategies are voltage, power, PZT power density, spatial power density and specific power density. The results are also compared with other similar work. In general, structure with an addition of silicon rubber beam was found to give the best power density output and produce 253% increase of power ouput as compared to basic PZT energy harvester.

scholarly journals Load Resistance Optimization of a Broadband Bistable Piezoelectric Energy Harvester for Primary Harmonic and Subharmonic Behaviors

2021 ◽  
Vol 13 (5) ◽  
pp. 2865 ◽  
Author(s):  
Sungryong Bae ◽  
Pilkee Kim
Keyword(s):  
Energy Harvester ◽  
Load Resistance ◽  
Oscillation Period ◽  
Ambient Vibration ◽  
Ambient Vibrations ◽  
Frequency Dependency ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Optimal Load ◽  
Bistable Energy Harvester

In this study, optimization of the external load resistance of a piezoelectric bistable energy harvester was performed for primary harmonic (period-1T) and subharmonic (period-3T) interwell motions. The analytical expression of the optimal load resistance was derived, based on the spectral analyses of the interwell motions, and evaluated. The analytical results are in excellent agreement with the numerical ones. A parametric study shows that the optimal load resistance depended on the forcing frequency, but not the intensity of the ambient vibration. Additionally, it was found that the optimal resistance for the period-3T interwell motion tended to be approximately three times larger than that for the period-1T interwell motion, which means that the optimal resistance was directly affected by the oscillation frequency (or oscillation period) of the motion rather than the forcing frequency. For broadband energy harvesting applications, the subharmonic interwell motion is also useful, in addition to the primary harmonic interwell motion. In designing such piezoelectric bistable energy harvesters, the frequency dependency of the optimal load resistance should be considered properly depending on ambient vibrations.

scholarly journals Power Density Improvement of Piezoelectric Energy Harvesters via a Novel Hybridization Scheme with Electromagnetic Transduction

Micromachines ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 803
Author(s):  
Zhongjie Li ◽  
Chuanfu Xin ◽  
Yan Peng ◽  
Min Wang ◽  
Jun Luo ◽  
...  
Keyword(s):  
Power Density ◽  
Output Power ◽  
Energy Harvester ◽  
Hybrid Energy ◽  
Energy Harvesters ◽  
Piezoelectric Patch ◽  
Piezoelectric Energy ◽  
Electromagnetic Transduction ◽  
Self Powered ◽  
Power Densities

A novel hybridization scheme is proposed with electromagnetic transduction to improve the power density of piezoelectric energy harvester (PEH) in this paper. Based on the basic cantilever piezoelectric energy harvester (BC-PEH) composed of a mass block, a piezoelectric patch, and a cantilever beam, we replaced the mass block by a magnet array and added a coil array to form the hybrid energy harvester. To enhance the output power of the electromagnetic energy harvester (EMEH), we utilized an alternating magnet array. Then, to compare the power density of the hybrid harvester and BC-PEH, the experiments of output power were conducted. According to the experimental results, the power densities of the hybrid harvester and BC-PEH are, respectively, 3.53 mW/cm3 and 5.14 μW/cm3 under the conditions of 18.6 Hz and 0.3 g. Therefore, the power density of the hybrid harvester is 686 times as high as that of the BC-PEH, which verified the power density improvement of PEH via a hybridization scheme with EMEH. Additionally, the hybrid harvester exhibits better performance for charging capacitors, such as charging a 2.2 mF capacitor to 8 V within 17 s. It is of great significance to further develop self-powered devices.

Sign in / Sign up

Export Citation Format

Share Document