scholarly journals Autonomous Energy Harvester Based on Textile-Based Enzymatic Biofuel Cell for On-Demand Usage

Sensors ◽  
2020 ◽  
Vol 20 (17) ◽  
pp. 5009
Author(s):  
Seonho Seok ◽  
Cong Wang ◽  
Elie Lefeuvre ◽  
Jungyul Park
Keyword(s):  
Power Management ◽  
Output Power ◽  
Output Voltage ◽  
Energy Harvester ◽  
Power Level ◽  
Biofuel Cell ◽  
Output Power Level ◽  
Crystal Oscillator ◽  
On Demand ◽  
Enzymatic Biofuel Cell

This paper presents an autonomous energy harvester based on a textile-based enzymatic biofuel cell, enabling an efficient power management and on-demand usage. The proposed biofuel cell works by an enzymatic reaction with glucose in sweat absorbed by the specially designed textile for sustainable and efficient energy harvesting. The output power of the textile-based biofuel cell has been optimized by changing electrode size and stacking electrodes and corresponding fluidic channels suitable for following power management circuit. The output power level of single electrode is estimated less than 0.5 μW and thus a two-staged power management circuit using intermediate supercapacitor has been presented. As a solution to produce a higher power level, multiple stacks of biofuel cell electrodes have been proposed and thus the textile-based biofuel cell employing serially connected 5 stacks produces a maximal power of 13 μW with an output voltage of 0.88 V when load resistance is 40 kΩ. A buck-boost converter employing a crystal oscillator directly triggered by DC output voltage of the biofuel cell makes it possible to obtain output voltage of the DC–DC converter is 6.75 V. The efficiency of the DC–DC converter is estimated as approximately 50% when the output power of the biofuel cell is tens microwatts. In addition, LT-spice modeling and simulation has been presented to estimate power consumption of each element of the proposed DC–DC converter circuit and the predicted output voltage has good agreement with measurement result.

scholarly journals Analytical Modeling of a Doubly Clamped Flexible Piezoelectric Energy Harvester with Axial Excitation and Its Experimental Characterization

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3861
Author(s):  
Jie Mei ◽  
Qiong Fan ◽  
Lijie Li ◽  
Dingfang Chen ◽  
Lin Xu ◽  
...  
Keyword(s):  
Output Power ◽  
Power Output ◽  
Output Voltage ◽  
Energy Harvester ◽  
Load Resistance ◽  
Engineering Practice ◽  
Maximum Output ◽  
Widespread Application ◽  
Piezoelectric Energy ◽  
Axial Excitation

With the rapid development of wearable electronics, novel power solutions are required to adapt to flexible surfaces for widespread applications, thus flexible energy harvesters have been extensively studied for their flexibility and stretchability. However, poor power output and insufficient sensitivity to environmental changes limit its widespread application in engineering practice. A doubly clamped flexible piezoelectric energy harvester (FPEH) with axial excitation is therefore proposed for higher power output in a low-frequency vibration environment. Combining the Euler–Bernoulli beam theory and the D’Alembert principle, the differential dynamic equation of the doubly clamped energy harvester is derived, in which the excitation mode of axial load with pre-deformation is considered. A numerical solution of voltage amplitude and average power is obtained using the Rayleigh–Ritz method. Output power of 22.5 μW at 27.1 Hz, with the optimal load resistance being 1 MΩ, is determined by the frequency sweeping analysis. In order to power electronic devices, the converted alternating electric energy should be rectified into direct current energy. By connecting to the MDA2500 standard rectified electric bridge, a rectified DC output voltage across the 1 MΩ load resistor is characterized to be 2.39 V. For further validation of the mechanical-electrical dynamical model of the doubly clamped flexible piezoelectric energy harvester, its output performances, including both its frequency response and resistance load matching performances, are experimentally characterized. From the experimental results, the maximum output power is 1.38 μW, with a load resistance of 5.7 MΩ at 27 Hz, and the rectified DC output voltage reaches 1.84 V, which shows coincidence with simulation results and is proved to be sufficient for powering LED electronics.

scholarly journals A 350-GHz Coupled Stack Oscillator with −0.8 dBm Output Power in 65-nm Bulk CMOS Process

Electronics ◽  
2020 ◽  
Vol 9 (8) ◽  
pp. 1214
Author(s):  
Thanh Dat Nguyen ◽  
Jong-Phil Hong
Keyword(s):  
Output Power ◽  
Supply Voltage ◽  
Second Harmonic ◽  
Power Level ◽  
Cmos Technology ◽  
Negative Resistance ◽  
Output Power Level ◽  
Cmos Process ◽  
Frequency Selective ◽  
Oscillation Frequencies

This paper presents a push-push coupled stack oscillator that achieves a high output power level at terahertz (THz) wave frequency. The proposed stack oscillator core adopts a frequency selective negative resistance topology to improve negative transconductance at the fundamental frequency and a transformer connected between gate and drain terminals of cross pair transistors to minimize the power loss at the second harmonic frequency. Next, the phases and the oscillation frequencies between the oscillator cores are locked by employing an inductor of frequency selective negative resistance topology. The proposed topology was implemented in a 65-nm bulk CMOS technology. The highest measured output power is −0.8 dBm at 353.2 GHz while dissipating 205 mW from a 2.8 V supply voltage.

scholarly journals A Novel Energy Harvester for Powering Small UAVs: Performance Analysis, Model Validation and Flight Results

Sensors ◽  
2019 ◽  
Vol 19 (8) ◽  
pp. 1771 ◽  
Author(s):  
Rocco Citroni ◽  
Franco Di Paolo ◽  
Patrizia Livreri
Keyword(s):  
Energy Harvester ◽  
Power Level ◽  
Micro Air Vehicles ◽  
Unmanned Vehicles ◽  
Output Power Level ◽  
Analysis Model ◽  
New Class ◽  
Mission Duration ◽  
Preliminary Study ◽  
New Strategies

The proposed work aims at exploring and developing new strategies to extend mission parameters (measured as travel distance and mission duration (MD)) of a new class of unmanned vehicles, named Micro Air Vehicles (MAVs). In this paper, a new analytical model, identifying all factors, which determine the MAV power consumption, is presented. Starting from the new model, the design of a nanoarray energy harvester, based on plasmonics nano-antenna technology is proposed. The preliminary study was based on a 22,066,058 22,066,058 × 62,800-dipole rectenna array producing an output power level of 84.14 mW, and an energy value of 2572 J under a power density of 100 mW/cm² and a resonant frequency of 350 THz as input conditions. The preliminary analytical results show a possible recharge of an ultra-fast rechargeable battery on board of a MAV and an MD improvement of 16.30 min.

scholarly journals Hybrid Raman-Erbium Random Fiber Laser with a Half Open Cavity Assisted by Artificially Controlled Backscattering Fiber Reflectors

2021 ◽  
Author(s):  
R. A. Perez-Herrera ◽  
P. Roldan-Varona ◽  
M. Galarza ◽  
S. Sañudo-Lasagabaster ◽  
L. Rodriguez-Cobo ◽  
...  
Keyword(s):  
Fiber Laser ◽  
Output Power ◽  
Signal To Noise Ratio ◽  
Power Level ◽  
Laser Cavity ◽  
Gain Medium ◽  
Optical Signal ◽  
Open Cavity ◽  
Output Power Level ◽  
Erbium Doped

Abstract A hybrid Raman-erbium random fiber laser (RFL) with a half-open cavity assisted by chirped artificially controlled backscattering fiber reflectors (ACBFRs) is presented. A combination of 2.4 km of dispersion compensating fiber (DCF) with two highly erbium-doped fiber (EDF) pieces of 5 m length was used as gain medium. A single random laser emission line centered at 1553.8 nm with an output power level of -6.5 dBm and an optical signal to noise ratio (OSNR) of 47 dB was obtained when pumped at 37.5 dBm. A full width at half maximum (FHWM) of 1 nm and a 100% confidence level (CL) output power instability as low as 0.08 dB were measured. The utilization of the new laser cavity as a temperature and strain sensor is also experimentally studied.

scholarly journals Optimal Design and Comparison of High-Frequency Resonant and Non-Resonant Rotary Transformers

Energies ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 929 ◽  
Author(s):  
Koen Bastiaens ◽  
Dave C. J. Krop ◽  
Sultan Jumayev ◽  
Elena A. Lomonova
Keyword(s):  
Comparative Analysis ◽  
Optimal Design ◽  
Output Power ◽  
High Frequency ◽  
Power Level ◽  
Physical Design ◽  
Design Approach ◽  
Output Power Level ◽  
The Core ◽  
Series Resonant

This paper concerns the optimal design and comparative analysis of resonant and non-resonant high-frequency GaN-based rotating transformers. A multi-physical design approach is employed, in which magnetic, electrical, and thermal models are coupled. The results are verified by experiments. Two different optimization objectives are considered; firstly, the efficiency of two standard core geometries is maximized for a required output power level. Secondly, a geometrical optimization is performed, such that the core inertia is minimized for the desired output power level. The results of both design optimizations have shown large improvements in terms of output power and core inertia as a result of applying series–series resonant compensation.

scholarly journals Piezoelectric Performance of a Symmetrical Ring-Shaped Piezoelectric Energy Harvester Using PZT-5H under a Temperature Gradient

Micromachines ◽  
2020 ◽  
Vol 11 (7) ◽  
pp. 640
Author(s):  
Nannan Zhou ◽  
Rongqi Li ◽  
Hongrui Ao ◽  
Chuanbing Zhang ◽  
Hongyuan Jiang
Keyword(s):  
Growth Rate ◽  
Output Power ◽  
Output Voltage ◽  
Electromechanical Coupling ◽  
Energy Harvester ◽  
Rapid Development ◽  
Coupling Model ◽  
Output Performance ◽  
Piezoelectric Energy ◽  
Changing Trend

With the rapid development of microelectronics technology, low-power electronic sensors have been widely applied in many fields, such as Internet of Things, aerospace, and so on. In this paper, a symmetrical ring-shaped piezoelectric energy harvester (SR-PEH) is designed to provide energy for the sensor to detect the ambient temperature. The finite element method is used by utilizing software COMSOL 5.4, and the electromechanical coupling model of the piezoelectric cantilever is established. The output performance equations are proposed; the microelectromechanical system (MEMS) integration process of the SR-PEH, circuit, and sensor is stated; and the changing trend of the output power density is explained from an energy perspective. In the logarithmic coordinate system, the results indicate that the output voltage and output power are approximately linear with the temperature when the resistance is constant. In addition, the growth rate of the output voltage and output power decreases with an increase of resistance under the condition of constant temperature. In addition, with an increase of temperature, the growth rate of the output power is faster than that of the output voltage. Furthermore, resistance has a more dramatic effect on the output voltage, whereas temperature has a more significant effect on the output power. More importantly, the comparison with the conventional cantilever-shaped piezoelectric energy harvester (CC-PEH) shows that the SR-PEH can improve the output performance and broaden the frequency band.

Sign in / Sign up

Export Citation Format

Share Document