scholarly journals PCB-Based Magnetometer as a Platform for Quantification of Lateral-Flow Assays

Sensors ◽  
2019 ◽  
Vol 19 (24) ◽  
pp. 5433 ◽  
Author(s):  
Mohammad Khodadadi ◽  
Long Chang ◽  
João R. C. Trabuco ◽  
Binh V. Vu ◽  
Katerina Kourentzi ◽  
...  
Keyword(s):  
High Precision ◽  
Fe3o4 Nanoparticles ◽  
Printed Circuit Board ◽  
Test Line ◽  
Point Of Care ◽  
Low Cost ◽  
Superparamagnetic Iron Oxide ◽  
High Sensitivity ◽  
Lateral Flow ◽  
Circuit Board

This work presents a proof-of-concept demonstration of a novel inductive transducer, the femtoMag, that can be integrated with a lateral-flow assay (LFA) to provide detection and quantification of molecular biomarkers. The femtoMag transducer is manufactured using a low-cost printed circuit board (PCB) technology and can be controlled by relatively inexpensive electronics. It allows rapid high-precision quantification of the number (or amount) of superparamagnetic nanoparticle reporters along the length of an LFA test strip. It has a detection limit of 10−10 emu, which is equivalent to detecting 4 ng of superparamagnetic iron oxide (Fe3O4) nanoparticles. The femtoMag was used to quantify the hCG pregnancy hormone by quantifying the number of 200 nm magnetic reporters (superparamagnetic Fe3O4 nanoparticles embedded into a polymer matrix) immuno-captured within the test line of the LFA strip. A sensitivity of 100 pg/mL has been demonstrated. Upon further design and control electronics improvements, the sensitivity is projected to be better than 10 pg/mL. Analysis suggests that an average of 109 hCG molecules are needed to specifically bind 107 nanoparticles in the test line. The ratio of the number of hCG molecules in the sample to the number of reporters in the test line increases monotonically from 20 to 500 as the hCG concentration increases from 0.1 ng/mL to 10 ng/mL. The low-cost easy-to-use femtoMag platform offers high-sensitivity/high-precision target analyte quantification and promises to bring state-of-the-art medical diagnostic tests to the point of care.

scholarly journals Integrating high-performing electrochemical transducers in lateral flow assay

2021 ◽  
Author(s):  
Antonia Perju ◽  
Nongnoot Wongkaew
Keyword(s):  
High Performance ◽  
Point Of Care ◽  
Low Cost ◽  
High Sensitivity ◽  
Lateral Flow ◽  
Analytical Performance ◽  
Label Free ◽  
High Performing ◽  
Lateral Flow Assays ◽  
Electrochemical Transducers

AbstractLateral flow assays (LFAs) are the best-performing and best-known point-of-care tests worldwide. Over the last decade, they have experienced an increasing interest by researchers towards improving their analytical performance while maintaining their robust assay platform. Commercially, visual and optical detection strategies dominate, but it is especially the research on integrating electrochemical (EC) approaches that may have a chance to significantly improve an LFA’s performance that is needed in order to detect analytes reliably at lower concentrations than currently possible. In fact, EC-LFAs offer advantages in terms of quantitative determination, low-cost, high sensitivity, and even simple, label-free strategies. Here, the various configurations of EC-LFAs published are summarized and critically evaluated. In short, most of them rely on applying conventional transducers, e.g., screen-printed electrode, to ensure reliability of the assay, and additional advances are afforded by the beneficial features of nanomaterials. It is predicted that these will be further implemented in EC-LFAs as high-performance transducers. Considering the low cost of point-of-care devices, it becomes even more important to also identify strategies that efficiently integrate nanomaterials into EC-LFAs in a high-throughput manner while maintaining their favorable analytical performance.

Electrical impedance sensing of organic pollutants with ultrathin graphitic membranes

2021 ◽  
Author(s):  
Marian Baah ◽  
Afifa Rahman ◽  
Sarah Sibilia ◽  
Gianmarco Trezza ◽  
Luigi Ferrigno ◽  
...  
Keyword(s):  
Organic Pollutants ◽  
Electrical Impedance ◽  
Printed Circuit Board ◽  
Ad Hoc ◽  
Low Cost ◽  
High Sensitivity ◽  
Pyrolytic Carbon ◽  
Circuit Board ◽  
Multilayer Graphene ◽  
Sio2 Substrate

Abstract In this paper, we propose an original approach for the real-time detection of industrial organic pollutants in water. It is based on the monitoring of the time evolution of the electrical impedance of low-cost graphitic nanomembranes. The developed approach exploits the high sensitivity of the impedance of 2D graphene-related materials to the adsorbents. We examined sensitivity of the nanomembranes based on Pyrolyzed Photoresist (PPF), Pyrolytic Carbon (PyC), and Multilayer Graphene (MLG) films. In order to realize a prototype of a sensor capable of monitoring the pollutants in water, the membranes were integrated into an ad-hoc printed circuit board. We demonstrated the correlation between the sensitivity of the electric impedance to adsorbents and the structure of the nanomembranes, and revealed that the amorphous PyC, being most homogeneous and adhesive to the SiO2 substrate, is the most promising in terms of integration into industrial pollutants sensors.

scholarly journals Characterization of Inkjet-Printed Digital Microfluidics Devices

Sensors ◽  
2021 ◽  
Vol 21 (9) ◽  
pp. 3064
Author(s):  
Shiyu Chen ◽  
Zhidong He ◽  
Suhwan Choi ◽  
Igor V. Novosselov
Keyword(s):  
Printed Circuit Board ◽  
Dielectric Breakdown ◽  
Point Of Care ◽  
Low Cost ◽  
Digital Microfluidics ◽  
Actuation Voltage ◽  
Circuit Board ◽  
Pmma Layer ◽  
Design Iteration ◽  
Droplet Movement

Digital microfluidics (DMF) devices enable precise manipulation of small liquid volumes in point-of-care testing. A printed circuit board (PCB) substrate is commonly utilized to build DMF devices. However, inkjet printing can be used to fabricate DMF circuits, providing a less expensive alternative to PCB-based DMF designs while enabling more rapid design iteration cycles. We demonstrate the cleanroom-free fabrication process of a low-cost inkjet-printed DMF circuit. We compare Kapton and polymethyl methacrylate (PMMA) as dielectric coatings by measuring the minimal droplet actuation voltage for a range of actuation frequencies. A minimum actuation voltage of 5.6 V was required for droplet movement with the PMMA layer thickness of 0.2 μm and a hydrophobic layer of 0.17 μm. Significant issues with PMMA dielectric breakdown were observed at actuation voltages above 10 V. In comparison, devices that utilized Kapton were found to be more robust, even at an actuation voltage up to 100 V.

scholarly journals Substrate-integrated photonic doping for near-zero-index devices

2019 ◽  
Vol 10 (1) ◽  
Author(s):  
Ziheng Zhou ◽  
Yue Li ◽  
Hao Li ◽  
Wangyu Sun ◽  
Iñigo Liberal ◽  
...  
Keyword(s):  
Printed Circuit Board ◽  
Low Cost ◽  
Integrated Design ◽  
High Sensitivity ◽  
Circuit Board ◽  
Dielectric Sensor ◽  
Exciting Potential ◽  
Wave Phenomena ◽  
Zero Index ◽  
Zero Phase

Abstract Near-zero-index (NZI) media, a medium with near zero permittivity and/or permeability, exhibits unique wave phenomena and exciting potential for multiple applications. However, previous proof-of-concept realizations of NZI media based on bulky and expensive platforms are not easily compatible with low-cost and miniaturization demands. Here, we propose the method of substrate-integrated (SI) photonic doping, enabling the implementation of NZI media within a printed circuit board (PCB) integrated design. Additionally, the profile of the NZI device is reduced by half by using symmetries. We validate the concept experimentally by demonstrating NZI supercoupling in straight and curve substrate integrated waveguides, also validating properties of position-independent photonic doping, zero-phase advance and finite group delay. Based on this platform, we propose design of three NZI devices: a high-sensitivity dielectric sensor, an efficient acousto-microwave modulator, and an arbitrarily-curved ‘electric fiber’. Our results represent an important step forward in the development of NZI technologies for microwave/terahertz applications.

scholarly journals Isothermal Recombinase Polymerase Amplification (RPA) of E. coli gDNA in Commercially Fabricated PCB-Based Microfluidic Platforms

Micromachines ◽  
2021 ◽  
Vol 12 (11) ◽  
pp. 1387
Author(s):  
Maria Georgoutsou-Spyridonos ◽  
Myrto Filippidou ◽  
Georgia D. Kaprou ◽  
Dimitrios C. Mastellos ◽  
Stavros Chatzandroulis ◽  
...  
Keyword(s):  
Target Genes ◽  
Printed Circuit Board ◽  
Point Of Care ◽  
Low Cost ◽  
Recombinase Polymerase Amplification ◽  
Circuit Board ◽  
Microfluidic Platforms ◽  
Seamless Integration ◽  
E Coli ◽  
First Time

Printed circuit board (PCB) technology has been recently proposed as a convenient platform for seamlessly integrating electronics and microfluidics in the same substrate, thus facilitating the introduction of integrated and low-cost microfluidic devices to the market, thanks to the inherent upscaling potential of the PCB industry. Herein, a microfluidic chip, encompassing on PCB both a meandering microchannel and microheaters to accommodate recombinase polymerase amplification (RPA), is designed and commercially fabricated for the first time on PCB. The developed microchip is validated for RPA-based amplification of two E. coli target genes compared to a conventional thermocycler. The RPA performance of the PCB microchip was found to be well-comparable to that of a thermocycler yet with a remarkably lower power consumption (0.6 W). This microchip is intended for seamless integration with biosensors in the same PCB substrate for the development of a point-of-care (POC) molecular diagnostics platform.

A Novel Wideband transition from Substrate Integrated Waveguide to Rectangular Waveguide

2020 ◽  
Vol 10 ◽  
Author(s):  
Keyur Mahant ◽  
Hiren Mewada ◽  
Amit Patel ◽  
Alpesh Vala ◽  
Jitendra Chaudhari
Keyword(s):  
Rectangular Waveguide ◽  
Printed Circuit Board ◽  
Low Cost ◽  
Single Layer ◽  
Circuit Board ◽  
Substrate Integrated Waveguide ◽  
Ka Band ◽  
Better Than ◽  
Millimeter Wave Circuits ◽  
Wideband Transition

Aim: In this article, wideband substrate integrated waveguide (SIW) and rectangular waveguide (RWG) transition operating in Ka-band is proposed Objective: In this article, wideband substrate integrated waveguide (SIW) and rectangular waveguide (RWG) transition operating in Ka-band is proposed. Method: Coupling patch etched on the SIW cavity to couple the electromagnetic energy from SIW to RWG. Moreover, metasurface is introduced into the radiating patch to enhance bandwidth. To verify the functionality of the proposed structure back to back transition is designed and fabricated on a single layer substrate using standard printed circuit board (PCB) fabrication technology. Results: Measured results matches with the simulation results, measured insertion loss is less than 1.2 dB and return loss is better than 3 dB for the frequency range of 28.8 to 36.3 GHz. By fabricating transition with 35 SRRs bandwidth of the proposed transition can be improved. Conclusion: The proposed transition has advantages like compact in size, easy to fabricate, low cost and wide bandwidth. Proposed structure is a good candidate for millimeter wave circuits and systems.

scholarly journals Evaluation of Production Lots of a Rapid Point-of-Care Lateral Flow Serological Test Intended for Identification of IgM and IgG against the N-Terminal Part of the Spike Protein (S1) of SARS-CoV-2

Viruses ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 1043
Author(s):  
Tove Hoffman ◽  
Linda Kolstad ◽  
Bengt Rönnberg ◽  
Åke Lundkvist
Keyword(s):  
Predictive Value ◽  
Serological Test ◽  
Point Of Care ◽  
External Validation ◽  
High Sensitivity ◽  
Lateral Flow ◽  
Spike Protein ◽  
Individual Level ◽  
Lateral Flow Test ◽  
Production Errors

The potential of rapid point-of-care (POC) tests has been subject of doubt due to an eventual risk of production errors. The aim was therefore to evaluate the two separate production lots of a commercial POC lateral flow test, intended for the detection of IgM and IgG against the SARS-CoV-2 spike protein (S1). Control samples consisted of serum from individuals with confirmed SARS-CoV-2 infection and pre-COVID-19 negative sera gathered from a biobank. The presence of anti-S1 IgM/IgG in the sera was verified by an in-house Luminex-based serological assay (COVID-19 SIA). One hundred samples were verified as positive for anti-S1 IgG and 74 for anti-S1 IgM. Two hundred samples were verified as negative for anti-S1 IgM/IgG. For the two lots of the POC-test, the sensitivities were 93.2% and 87.8% for IgM and 93.0% and 100% for IgG. The specificities were 100% for IgM and 99.5% for IgG. The positive predictive value was 100% for IgM and 98.9% and 99.0% for IgG. The negative predictive value was 97.6% and 95.7% for IgM, and 96.6% and 100% for IgG. The evaluated POC-test is suitable to assess anti-SARS-CoV-2 S1 IgM and IgG, as a measure of previous virus exposure on an individual level. The external validation of separate lots of rapid POC-tests is encouraged to ensure high sensitivity before market introduction.

scholarly journals Highly Compact Through-Wire Microstrip to Empty Substrate Integrated Coaxial Line Transition

2021 ◽  
Vol 11 (15) ◽  
pp. 6885
Author(s):  
Marcos D. Fernandez ◽  
José A. Ballesteros ◽  
Angel Belenguer
Keyword(s):  
Printed Circuit Board ◽  
Low Cost ◽  
Coaxial Line ◽  
Circuit Board ◽  
Central Layer ◽  
Printed Circuit ◽  
Integrated Technology ◽  
Low Profile ◽  
The Many ◽  
High Degree

Empty substrate integrated coaxial line (ESICL) technology preserves the many advantages of the substrate integrated technology waveguides, such as low cost, low profile, or integration in a printed circuit board (PCB); in addition, ESICL is non-dispersive and has low radiation. To date, only two transitions have been proposed in the literature that connect the ESICL to classical planar lines such as grounded coplanar and microstrip. In both transitions, the feeding planar lines and the ESICL are built in the same substrate layer and they are based on transformed structures in the planar line, which must be in the central layer of the ESICL. These transitions also combine a lot of metallized and non-metallized parts, which increases the complexity of the manufacturing process. In this work, a new through-wire microstrip-to-ESICL transition is proposed. The feeding lines and the ESICL are implemented in different layers, so that the height of the ESICL can be independently chosen. In addition, it is a highly compact transition that does not require a transformer and can be freely rotated in its plane. This simplicity provides a high degree of versatility in the design phase, where there are only four variables that control the performance of the transition.

scholarly journals A Self-Powered Nanogenerator for the Electrical Protection of Integrated Circuits from Trace Amounts of Liquid

2019 ◽  
Vol 12 (1) ◽  
Author(s):  
Zhuang Hui ◽  
Ming Xiao ◽  
Daozhi Shen ◽  
Jiayun Feng ◽  
Peng Peng ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
High Performance ◽  
Printed Circuit Board ◽  
Short Circuit ◽  
High Sensitivity ◽  
Short Circuit Current ◽  
Fast Response ◽  
Open Circuit ◽  
Circuit Board ◽  
Self Powered

Abstract With the increase in the use of electronic devices in many different environments, a need has arisen for an easily implemented method for the rapid, sensitive detection of liquids in the vicinity of electronic components. In this work, a high-performance power generator that combines carbon nanoparticles and TiO2 nanowires has been fabricated by sequential electrophoretic deposition (EPD). The open-circuit voltage and short-circuit current of a single generator are found to exceed 0.7 V and 100 μA when 6 μL of water was applied. The generator is also found to have a stable and reproducible response to other liquids. An output voltage of 0.3 V was obtained after 244, 876, 931, and 184 μs, on exposure of the generator to 6 μL of water, ethanol, acetone, and methanol, respectively. The fast response time and high sensitivity to liquids show that the device has great potential for the detection of small quantities of liquid. In addition, the simple easily implemented sequential EPD method ensures the high mechanical strength of the device. This compact, reliable device provides a new method for the sensitive, rapid detection of extraneous liquids before they can impact the performance of electronic circuits, particularly those on printed circuit board.

Sign in / Sign up

Export Citation Format

Share Document