scholarly journals Experimental Analysis and Model Validation on the Performance of Impregnated Activated Carbons for the Removal of Hydrogen Sulfide (H2S) from Sewage Biogas

Processes ◽  
2019 ◽  
Vol 7 (9) ◽  
pp. 548 ◽  
Author(s):  
Davide Papurello ◽  
Marta Gandiglio ◽  
Andrea Lanzini
Keyword(s):  
Adsorption Capacity ◽  
Organic Waste ◽  
Activated Carbons ◽  
Biogas Production ◽  
Gas Mixture ◽  
Adsorption Model ◽  
Breakthrough Time ◽  
Power Generator ◽  
Langmuir Isotherm Model ◽  
Good Agreement

Organic waste exploitation is crucial for waste emissions restraint in air, soil and water. This type of waste can be exploited to produce biogas, a valuable fuel exploitable for energy purposes. A circular approach for energy production is much cleaner and more sustainable than the traditional linear approach. In this work, organic waste was used for biogas production to feed a highly efficient solid oxide fuel cell power generator, which requires an ultra-purified fuel. Commercial sorbents were experimentally studied in conjunction with a dynamic adsorption model to predict the breakthrough time and organize the material change-over. In the presence of 0.1% oxygen in the gas mixture, AirDep® CKC showed a marked increase in the adsorption capacity (from 3.91 to 84.87 mg/g), overcoming SulfaTrap® R8G (49.91 mg/g). The effect of several operating parameters on adsorption capacity was evaluated: inlet H2S concentration, filter geometry and gas mixture velocity. Experimental data revealed that adsorption capacity increases with initial H2S concentration, following the typical trend of the Langmuir isotherm. Model simulations were in good agreement compared to experimental results, with an average relative error lower than 7%. A sensitivity analysis on the adsorption capacity was accomplished considering parameters from operational and empirical correlations.

scholarly journals Nascent Rice Husk as an Adsorbent for Removing Cationic Dyes from Textile Wastewater

2020 ◽  
Vol 10 (10) ◽  
pp. 3437
Author(s):  
Jude Ofei Quansah ◽  
Thandar Hlaing ◽  
Fritz Ndumbe Lyonga ◽  
Phyo Phyo Kyi ◽  
Seung-Hee Hong ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Rice Husk ◽  
Textile Wastewater ◽  
Cationic Dyes ◽  
Adsorption Model ◽  
Order Model ◽  
Solution Ph ◽  
Freundlich Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

We assessed the applicability of rice husk (RH) to remove cationic dyes, i.e., methylene blue (MB) and crystal violet (CV), from water. RH thermally treated at 75 °C showed a higher adsorption capacity than that at high temperatures (300–700 °C). For a suitable CV-adsorption model, a pseudo-first-order model for MB adsorption was followed by the kinetics adsorption process; however, a pseudo-second-order model was then suggested. In the qt versus t1/2 plot, the MB line passed through the origin, but that of CV did not. The Langmuir isotherm model was better than the Freundlich model for both dye adsorptions; furthermore, the adsorption capacity for MB and CV was 24.48 mg/g and 25.46 mg/g, respectively. Thermodynamically, the adsorption of both MB and CV onto the RH was found to be spontaneous and endothermic. This adsorption increased insignificantly on increasing the solution pH from 4 to 10. With an increasing dosage of the RH, there was an increase in the removal percentages of MB and CV; however, adsorption capacity per unit mass of the RH was observed to decrease. Therefore, we conclude that utilizing RH as an available and affordable adsorbent is feasible to remove MB and CV from wastewater.

scholarly journals Biogas Purification: A Comparison of Adsorption Performance in D4 Siloxane Removal Between Commercial Activated Carbons and Waste Wood-Derived Char Using Isotherm Equations

Processes ◽  
2019 ◽  
Vol 7 (10) ◽  
pp. 774 ◽  
Author(s):  
Papurello ◽  
Gandiglio ◽  
Kafashan ◽  
Lanzini
Keyword(s):  
Adsorption Capacity ◽  
Adsorption Isotherms ◽  
Activated Carbons ◽  
Biogas Production ◽  
Pollutant Emissions ◽  
Low Concentrations ◽  
Biogas Purification ◽  
Porous Volume ◽  
Trace Compounds ◽  
Isotherm Equations

Biogas production from organic waste could be an option to reduce landfill and pollutant emissions into air, water, and soil. These fuels contain several trace compounds that are crucial for highly efficient energy generators or gas injection into the grid. The ability of adsorbents to physically remove such adsorbates was investigated using adsorption isotherms at a constant temperature. We experimentally modelled isotherms for siloxane removal. Siloxanes were considered due to their high impact on energy generators performance even at low concentrations. Octamethylcyclotetrasiloxane was selected as a model compound and was tested using commercially available carbon and char derived from waste materials. The results show that recyclable material can be used in an energy production site and that char must be activated to improve its removal performance. The adsorption capacity is a function of specific surface area and porous volume rather than the elemental composition. The most common adsorption isotherms were employed to find the most appropriate isotherm to estimate the adsorption capacity and to compare the sorbents. The Dubinin-Radushkevich isotherm coupled with the Langmuir isotherm was found to be the best for estimating the adsorption capacity.

Competitive Biosorption of Pb(II) and Cu(II) by Functionalised Micropogonias undulates Scales

2020 ◽  
Vol 13 ◽  
Author(s):  
Joshua O. Ighalo ◽  
Ibrahim O. Tijani ◽  
Oluwaseun J. Ajala ◽  
Fisayo O. Ayandele ◽  
Omodele A. Eletta ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Low Cost ◽  
Fish Scales ◽  
Wet Impregnation ◽  
Monolayer Adsorption ◽  
Competitive Biosorption ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Best Fit

Background: Modified bio-based adsorbents from plant sources can be used for pollution remediation by adsorption due to their low cost and availability in large quantities. Objective: In this study, the competitive biosorption of Pb(II) and Cu(II) by Micropogonias undulates functionalised fish scales (FFS) was conducted. The functionalisation was done by wet impregnation with Fe2+. Method: The biosorbent was characterised by Fourier Transform Infrared Spectroscopy (FT-IR), Scanning Electron Microscopy with Energy-Dispersive X-ray Spectroscopy (SEM-EDS) and Branueur–Emmett–Teller (BET) analyses. Results: The major constituents in the FFS were calcium and phosphorus from the collagen and apatite on the scales. Optimum removal efficiency for both metals was >99% at 10 g/l dosage. It was observed that the Langmuir isotherm model and the pseudo second order kinetics model were the best fit for the experimental data. The monolayer adsorption capacity of FFS for Pb(II) and Cu(II) was observed to be 96.15 mg/g and 100 mg/g respectively. Conclusion: The study revealed that the competitive biosorption of heavy metals can be achieved (at a good adsorption capacity) using functionalised Micropogonias undulates fish scales.

scholarly journals Effective Poly (Cyclotriphosphazene-Co-4,4′-Sulfonyldiphenol)@rGO Sheets for Tetracycline Adsorption: Fabrication, Characterization, Adsorption Kinetics and Thermodynamics

Nanomaterials ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1540
Author(s):  
Muhammad Ahmad ◽  
Tehseen Nawaz ◽  
Mohammad Mujahid Alam ◽  
Yasir Abbas ◽  
Shafqat Ali ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Surface Area ◽  
High Surface ◽  
High Surface Area ◽  
High Adsorption ◽  
Clean Environment ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
High Adsorption Capacity ◽  
Adsorption Equilibrium Data

The development of excellent drug adsorbents and clarifying the interaction mechanisms between adsorbents and adsorbates are greatly desired for a clean environment. Herein, we report that a reduced graphene oxide modified sheeted polyphosphazene (rGO/poly (cyclotriphosphazene-co-4,4′-sulfonyldiphenol)) defined as PZS on rGO was used to remove the tetracycline (TC) drug from an aqueous solution. Compared to PZS microspheres, the adsorption capacity of sheeted PZS@rGO exhibited a high adsorption capacity of 496 mg/g. The adsorption equilibrium data well obeyed the Langmuir isotherm model, and the kinetics isotherm was fitted to the pseudo-second-order model. Thermodynamic analysis showed that the adsorption of TC was an exothermic, spontaneous process. Furthermore, we highlighted the importance of the surface modification of PZS by the introduction of rGO, which tremendously increased the surface area necessary for high adsorption. Along with high surface area, electrostatic attractions, H-bonding, π-π stacking and Lewis acid-base interactions were involved in the high adsorption capacity of PZS@rGO. Furthermore, we also proposed the mechanism of TC adsorption via PZS@rGO.

scholarly journals Sugarcane Bagasse as a Co-Substrate with Oil-Refinery Biological Sludge for Biogas Production Using Batch Mesophilic Anaerobic Co-Digestion Technology: Effect of Carbon/Nitrogen Ratio

Water ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 590
Author(s):  
Aiban Abdulhakim Saeed Ghaleb ◽  
Shamsul Rahman Mohamed Kutty ◽  
Gasim Hayder Ahmed Salih ◽  
Ahmad Hussaini Jagaba ◽  
Azmatullah Noor ◽  
...  
Keyword(s):  
Anaerobic Digestion ◽  
Sugarcane Bagasse ◽  
Organic Waste ◽  
Wastewater Treatment Plants ◽  
Biogas Production ◽  
Raw Materials ◽  
Oil Refinery ◽  
Methane Yield ◽  
Oil Refineries ◽  
Biological Sludge

Man-made organic waste leads to the rapid proliferation of pollution around the globe. Effective bio-waste management can help to reduce the adverse effects of organic waste while contributing to the circular economy at the same time. The toxic oily-biological sludge generated from oil refineries’ wastewater treatment plants is a potential source for biogas energy recovery via anaerobic digestion. However, the oily-biological sludge’s carbon/nitrogen (C/N) ratio is lower than the ideal 20–30 ratio required by anaerobic digestion technology for biogas production. Sugarcane bagasse can be digested as a high C/N co-substrate while the oily-biological sludge acts as a substrate and inoculum to improve biogas production. In this study, the best C/N with co-substrate volatile solids (VS)/inoculum VS ratios for the co-digestion process of mixtures were determined empirically through batch experiments at temperatures of 35–37 °C, pH (6–8) and 60 rpm mixing. The raw materials were pre-treated mechanically and thermo-chemically to further enhance the digestibility. The best condition for the sugarcane bagasse delignification process was 1% (w/v) sodium hydroxide, 1:10 solid-liquid ratio, at 100 °C, and 150 rpm for 1 h. The results from a 33-day batch anaerobic digestion experiment indicate that the production of biogas and methane yield were concurrent with the increasing C/N and co-substrate VS/inoculum VS ratios. The total biogas yields from C/N 20.0 with co-substrate VS/inoculum VS 0.06 and C/N 30.0 with co-substrate VS/inoculum VS 0.18 ratios were 2777.0 and 9268.0 mL, respectively, including a methane yield of 980.0 and 3009.3 mL, respectively. The biogas and methane yield from C/N 30.0 were higher than the biogas and methane yields from C/N 20.0 by 70.04 and 67.44%, respectively. The highest biogas and methane yields corresponded with the highest C/N with co-substrate VS/inoculum VS ratios (30.0 and 0.18), being 200.6 mL/g VSremoved and 65.1 mL CH4/g VSremoved, respectively.

scholarly journals Biogas potential of organic waste onboard cruise ships — a yet untapped energy source

2021 ◽  
Author(s):  
Kai Schumüller ◽  
Dirk Weichgrebe ◽  
Stephan Köster
Keyword(s):  
Energy Source ◽  
Anaerobic Digestion ◽  
Sewage Sludge ◽  
Food Waste ◽  
Energy Demand ◽  
Organic Waste ◽  
Biogas Production ◽  
Biogas Yield ◽  
Cruise Ships ◽  
Detailed Presentation

AbstractTo tap the organic waste generated onboard cruise ships is a very promising approach to reduce their adverse impact on the maritime environment. Biogas produced by means of onboard anaerobic digestion offers a complementary energy source for ships’ operation. This report comprises a detailed presentation of the results gained from comprehensive investigations on the gas yield from onboard substrates such as food waste, sewage sludge and screening solids. Each person onboard generates a total average of about 9 kg of organic waste per day. The performed analyses of substrates and anaerobic digestion tests revealed an accumulated methane yield of around 159 L per person per day. The anaerobic co-digestion of sewage sludge and food waste (50:50 VS) emerged as particularly effective and led to an increased biogas yield by 24%, compared to the mono-fermentation. In the best case, onboard biogas production can provide an energetic output of 82 W/P, on average covering 3.3 to 4.1% of the total energy demand of a cruise ship.

scholarly journals Fabrication of Carboxymethylcellulose/Metal-Organic Framework Beads for Removal of Pb(II) from Aqueous Solution

Materials ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 942 ◽  
Author(s):  
Huo-Xi Jin ◽  
Hong Xu ◽  
Nan Wang ◽  
Li-Ye Yang ◽  
Yang-Guang Wang ◽  
...  
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Photoelectron Spectroscopy ◽  
Langmuir Isotherm ◽  
Adsorption Equilibrium ◽  
Isotherm Model ◽  
Maximum Adsorption Capacity ◽  
X Ray ◽  
Metal Organic ◽  
Langmuir Isotherm Model

The ability to remove toxic heavy metals, such as Pb(II), from the environment is an important objective from both human-health and ecological perspectives. Herein, we describe the fabrication of a novel carboxymethylcellulose-coated metal organic material (MOF-5–CMC) adsorbent that removed lead ions from aqueous solutions. The adsorption material was characterized by Fourier-transform infrared spectroscopy, X-ray diffractometry, scanning electron microscopy, and X-ray photoelectron spectroscopy. We studied the functions of the contact time, pH, the original concentration of the Pb(II) solution, and adsorption temperature on adsorption capacity. MOF-5–CMC beads exhibit good adsorption performance; the maximum adsorption capacity obtained from the Langmuir isotherm-model is 322.58 mg/g, and the adsorption equilibrium was reached in 120 min at a concentration of 300 mg/L. The adsorption kinetics is well described by pseudo-second-order kinetics, and the adsorption equilibrium data are well fitted to the Langmuir isotherm model (R2 = 0.988). Thermodynamics experiments indicate that the adsorption process is both spontaneous and endothermic. In addition, the adsorbent is reusable. We conclude that MOF-5–CMC is a good adsorbent that can be used to remove Pb(II) from aqueous solutions.

Catalothermionic Power Generator Based on Internal Electron Emission in Ni/SiC Heterojunction Nanostructures

2009 ◽  
Author(s):  
Eduard G. Karpov ◽  
Ievgen I. Nedrygailov
Keyword(s):  
Energy Transfer ◽  
Electron Emission ◽  
Oxidation Reaction ◽  
Hydrogen Oxidation ◽  
Schottky Barriers ◽  
Gas Mixture ◽  
Hydrogen Oxidation Reaction ◽  
Power Generator ◽  
Oxidation Of Hydrogen ◽  
Internal Electron

We report on the unusual properties of single-faced SiC metal-semiconductor heterojunction nanostructures manifested by the ability to atalyze the hydrogen oxidation reaction, and also maintain internal electron emission over the Schottky barriers. As a result a stationary current has been detected in the preheated nanostructure when exposed to the oxyhydrogen gas mixture flux. The structures maintain both the non-adiabatic and electron-phonon channels of energy transfer, and the results of studies indicate the possibility for a very efficient conversion of chemical energy released in the catalytic oxidation of hydrogen into electricity.

Adsorption of Methylene Blue from Aqueous Solution Using Honeycomb-Cinder

2012 ◽  
Vol 550-553 ◽  
pp. 2259-2262
Author(s):  
Song Bo Cui ◽  
Hua Yong Zhang ◽  
Lu Yi Zhang
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Ph Value ◽  
Dye Wastewater ◽  
Batch System ◽  
Adsorption Data ◽  
Adsorption Processes ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Mb Adsorption

The adsorption behavior of methylene blue (MB) dye from aqueous solutions onto honeycomb-cinder (HC) and its acid-activated product was investigated in a batch system. The results showed the adsorption capacity was decreased for raw HC samples with the increase of pH value, while it was increased for activated samples. The adsorption data were fit with Langmuir isotherm model for MB adsorption by all samples. The MB adsorption capacity on samples was increased from 2.62 mg/g to 7.81 mg/g and 7.00 mg/g after acid-activated by HCl and H2SO4, respectively. The adsorption processes of MB followed pseudo-second-order kinetics with a coefficient of correlation≥0.99. This study demonstrated that acid-activated HC has superior adsorbing ability for MB than raw HC and can be used as alternative adsorbents in dye wastewater treatment.

Sign in / Sign up

Export Citation Format

Share Document