scholarly journals Antibacterial Chitosan Nanofiber Thin Films with Bacitracin Zinc Salt

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1104
Author(s):  
Kazutaka Kumamoto ◽  
Toshinari Maeda ◽  
Satoshi Hayakawa ◽  
Nurul Asyifah Binti Mustapha ◽  
Meng-Jiy Wang ◽  
...  
Keyword(s):  
Thin Films ◽  
High Surface ◽  
Volume Ratio ◽  
Zinc Salt ◽  
Uniform Structure ◽  
Fibroblast Cells ◽  
Chemical Bonds ◽  
Antibacterial Effects ◽  
Chitosan Nanofiber ◽  
Highly Uniform

Chitosan nanofiber has a highly uniform structure of 20–50 nm in diameter and shows high dispersibility in water due to its submicron size and high surface-to-volume ratio. The stacked nanofibers film is useful for breathability because it has a gap with a size of several tens of nm or more. However, the chemical bonds between the nanofibers cannot be broken during use. In this study, the thin films were obtained by filtration of chitosan nanofibers and 3-glycidoxypropyltrimethoxysilane (GPTMS) mixture. The addition of GPTMS changed the wettability, mechanical property and stability in water of the thin films. Bacitracin zinc salt (BZ) has been used for the localized dermatological medicines and loaded in the films. BZ interacted electrostatically with the thin films matrix and the release of BZ was controlled by the amount of GPTMS. A higher released amount of BZ showed higher antibacterial effects toward S. aureus. The film was also tested their toxicity by L929 fibroblasts. The release of less than 11.9 μg of BZ showed antibacterial effects, but were not toxic for fibroblast cells.

Transmission Electron Microscopy Study of Tin Oxide Thin Films Deposited on the Sapphire Substrate

2000 ◽  
Vol 6 (S2) ◽  
pp. 442-443
Author(s):  
J. E. Dominguez ◽  
L. Fu ◽  
X. Q. Pan
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Transmission Electron Microscopy ◽  
Tin Oxide ◽  
Gas Sensing ◽  
High Surface ◽  
Volume Ratio ◽  
Crystal Defects ◽  
Rutile Structure ◽  
Transmission Electron

Thin films of tin oxide (SnO2) with the rutile structure are the subject of many investigations due to their potential applications, such as gas sensing devices, lithium batteries cathodes and solar cells. There is a growing interest in the development of gas sensors using SnO2 thin films due to their high surface to volume ratio. Previous studies have shown that the gas sensing properties of SnO2 are very dependent on the microstructure and that doping elements can greatly influence their electrical properties. In this paper we present transmission electron microscopy (TEM) studies of the microstructure and crystal defects of SnO2 thin films.Tin oxide films 5 nm in thickness were deposited on the surface of sapphire (A12O3) by pulsed laser ablation of ceramic SnO2 targets. The film microstructure was studied using X ray diffraction, atomic force microscopy and transmission electron microscopy. Defects were studied using high resolution transmission electron microscopy (HRTEM).

scholarly journals Electrospun Nanofibers for Sensing and Biosensing Applications—A Review

2021 ◽  
Vol 22 (12) ◽  
pp. 6357
Author(s):  
Kinga Halicka ◽  
Joanna Cabaj
Keyword(s):  
High Surface ◽  
High Surface Area ◽  
Toxic Metal ◽  
Volume Ratio ◽  
Electrospun Nanofibers ◽  
Clinical Diagnostics ◽  
Loading Capacity ◽  
Electrospun Nanofiber ◽  
Sensing Platforms ◽  
Different Types

Sensors and biosensors have found applications in many areas, e.g., in medicine and clinical diagnostics, or in environmental monitoring. To expand this field, nanotechnology has been employed in the construction of sensing platforms. Because of their properties, such as high surface area to volume ratio, nanofibers (NFs) have been studied and used to develop sensors with higher loading capacity, better sensitivity, and faster response time. They also allow to miniaturize designed platforms. One of the most commonly used techniques of the fabrication of NFs is electrospinning. Electrospun NFs can be used in different types of sensors and biosensors. This review presents recent studies concerning electrospun nanofiber-based electrochemical and optical sensing platforms for the detection of various medically and environmentally relevant compounds, including glucose, drugs, microorganisms, and toxic metal ions.

scholarly journals Study of the geometry of open channels in a layer-bed-type microfluidic immobilized enzyme reactor

2021 ◽  
Author(s):  
Cynthia Nagy ◽  
Robert Huszank ◽  
Attila Gaspar
Keyword(s):  
Immobilized Enzyme ◽  
High Surface ◽  
Volume Ratio ◽  
Volumetric Flow Rate ◽  
Enzyme Reactor ◽  
Channel Pattern ◽  
Immobilized Enzyme Reactor ◽  
Split Flow ◽  
Parallel Streams ◽  
Enzymatic Microreactors

AbstractThis paper aims at studying open channel geometries in a layer-bed-type immobilized enzyme reactor with computer-aided simulations. The main properties of these reactors are their simple channel pattern, simple immobilization procedure, regenerability, and disposability; all these features make these devices one of the simplest yet efficient enzymatic microreactors. The high surface-to-volume ratio of the reactor was achieved using narrow (25–75 μm wide) channels. The simulation demonstrated that curves support the mixing of solutions in the channel even in strong laminar flow conditions; thus, it is worth including several curves in the channel system. In the three different designs of microreactor proposed, the lengths of the channels were identical, but in two reactors, the liquid flow was split to 8 or 32 parallel streams at the inlet of the reactor. Despite their overall higher volumetric flow rate, the split-flow structures are advantageous due to the increased contact time. Saliva samples were used to test the efficiencies of the digestions in the microreactors. Graphical abstract

scholarly journals A Review on Biosensors and Recent Development of Nanostructured Materials-Enabled Biosensors

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1109
Author(s):  
Varnakavi. Naresh ◽  
Nohyun Lee
Keyword(s):  
High Surface ◽  
Three Dimensional ◽  
Biological Response ◽  
Volume Ratio ◽  
Recent Decade ◽  
Disease Diagnosis ◽  
Electrical Signal ◽  
Detection Sensitivity ◽  
Wide Range ◽  
Color Tunability

A biosensor is an integrated receptor-transducer device, which can convert a biological response into an electrical signal. The design and development of biosensors have taken a center stage for researchers or scientists in the recent decade owing to the wide range of biosensor applications, such as health care and disease diagnosis, environmental monitoring, water and food quality monitoring, and drug delivery. The main challenges involved in the biosensor progress are (i) the efficient capturing of biorecognition signals and the transformation of these signals into electrochemical, electrical, optical, gravimetric, or acoustic signals (transduction process), (ii) enhancing transducer performance i.e., increasing sensitivity, shorter response time, reproducibility, and low detection limits even to detect individual molecules, and (iii) miniaturization of the biosensing devices using micro-and nano-fabrication technologies. Those challenges can be met through the integration of sensing technology with nanomaterials, which range from zero- to three-dimensional, possessing a high surface-to-volume ratio, good conductivities, shock-bearing abilities, and color tunability. Nanomaterials (NMs) employed in the fabrication and nanobiosensors include nanoparticles (NPs) (high stability and high carrier capacity), nanowires (NWs) and nanorods (NRs) (capable of high detection sensitivity), carbon nanotubes (CNTs) (large surface area, high electrical and thermal conductivity), and quantum dots (QDs) (color tunability). Furthermore, these nanomaterials can themselves act as transduction elements. This review summarizes the evolution of biosensors, the types of biosensors based on their receptors, transducers, and modern approaches employed in biosensors using nanomaterials such as NPs (e.g., noble metal NPs and metal oxide NPs), NWs, NRs, CNTs, QDs, and dendrimers and their recent advancement in biosensing technology with the expansion of nanotechnology.

scholarly journals Water uptake of various electrospun nonwovens

2020 ◽  
Vol 6 (3) ◽  
pp. 155-158
Author(s):  
Katharina Wulf ◽  
Volkmar Senz ◽  
Thomas Eickner ◽  
Sabine Illner
Keyword(s):  
Contact Angle ◽  
Surface Modification ◽  
Water Absorption ◽  
Water Uptake ◽  
Biomedical Applications ◽  
High Surface ◽  
Volume Ratio ◽  
Polymer Composition ◽  
Water Wetting ◽  
Morphology Changes

AbstractIn recent years, nanofiber based materials have emerged as especially interesting for several biomedical applications, regarding their high surface to volume ratio. Due to the superficial nano- and microstructuring and the different wettability compared to nonstructured surfaces, the water absorption is an important parameter with respect to the degradation stability, thermomechanic properties and drug release properties, depending on the type of polymer [1]. In this investigation, the water absorption of different non- and plasma modified biostable nanofiber nonwovens based on polyurethane, polyester and polyamide were analysed and compared. Also, the water absorption by specified water wetting, the contact angle and morphology changes were examined. The results show that the water uptake is highly dependent on the surface modification and the polymer composition itself and can therefore be partially changed.

scholarly journals Solar-blind ultraviolet photodetector based on vertically aligned single-crystalline β-Ga2O3 nanowire arrays

Nanophotonics ◽  
2020 ◽  
Vol 9 (15) ◽  
pp. 4497-4503
Author(s):  
Liying Zhang ◽  
Xiangqian Xiu ◽  
Yuewen Li ◽  
Yuxia Zhu ◽  
Xuemei Hua ◽  
...  
Keyword(s):  
Inductively Coupled Plasma ◽  
Light Trapping ◽  
High Surface ◽  
Volume Ratio ◽  
Average Diameter ◽  
Nanowire Arrays ◽  
Etching Technique ◽  
Inductively Coupled ◽  
Solar Blind ◽  
Vertically Aligned

AbstractVertically aligned nanowire arrays, with high surface-to-volume ratio and efficient light-trapping absorption, have attracted much attention for photoelectric devices. In this paper, vertical β-Ga2O3 nanowire arrays with an average diameter/height of 110/450 nm have been fabricated by the inductively coupled plasma etching technique. Then a metal-semiconductor-metal structured solar-blind photodetector (PD) has been fabricated by depositing interdigital Ti/Au electrodes on the nanowire arrays. The fabricated β-Ga2O3 nanowire PD exhibits ∼10 times higher photocurrent and responsivity than the corresponding film PD. Moreover, it also possesses a high photocurrent to dark current ratio (Ilight/Idark) of ∼104 and a ultraviolet/visible rejection ratio (R260 nm/R400 nm) of 3.5 × 103 along with millisecond-level photoresponse times.

scholarly journals High Power Impulse Magnetron Sputtering of In2O3/Sn Cold Sprayed Composite Target

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1228
Author(s):  
Marcin Winnicki ◽  
Artur Wiatrowski ◽  
Michał Mazur
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
High Voltage ◽  
High Power ◽  
Power Supply ◽  
Indium Tin Oxide ◽  
Volume Ratio ◽  
Cold Spraying ◽  
High Voltage Power Supply ◽  
Composite Target

High Power Impulse Magnetron Sputtering (HiPIMS) was used for deposition of indium tin oxide (ITO) transparent thin films at low substrate temperature. A hybrid-type composite target was self-prepared by low-pressure cold spraying process. Prior to spraying In2O3 and oxidized Sn powders were mixed in a volume ratio of 3:1. Composite In2O3/Sn coating had a mean thickness of 900 µm. HiPIMS process was performed in various mixtures of Ar:O2: (i) 100:0 vol.%, (ii) 90:10 vol.%, (iii) 75:25 vol.%, (iv) 50:50 vol.%, and (v) 0:100 vol.%. Oxygen rich atmosphere was necessary to oxidize tin atoms. Self-design, simple high voltage power switch capable of charging the 20 µF capacitor bank from external high voltage power supply worked as a power supply for an unbalanced magnetron source. ITO thin films with thickness in the range of 30–40 nm were obtained after 300 deposition pulses of 900 V and deposition time of 900 s. The highest transmission of 88% at λ = 550 nm provided 0:100 vol. % Ar:O2 mixture, together with the lowest resistivity of 0.03 Ω·cm.

scholarly journals Design Considerations for Borehole Thermal Energy Storage (BTES): A Review with Emphasis on Convective Heat Transfer

Geofluids ◽  
2019 ◽  
Vol 2019 ◽  
pp. 1-26 ◽  
Author(s):  
Helge Skarphagen ◽  
David Banks ◽  
Bjørn S. Frengstad ◽  
Harald Gether
Keyword(s):  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Theoretical Calculations ◽  
High Surface ◽  
High Surface Area ◽  
Volume Ratio ◽  
Thermal Recovery ◽  
Conductive Heat ◽  
Geological Environment

Borehole thermal energy storage (BTES) exploits the high volumetric heat capacity of rock-forming minerals and pore water to store large quantities of heat (or cold) on a seasonal basis in the geological environment. The BTES is a volume of rock or sediment accessed via an array of borehole heat exchangers (BHE). Even well-designed BTES arrays will lose a significant quantity of heat to the adjacent and subjacent rocks/sediments and to the surface; both theoretical calculations and empirical observations suggest that seasonal thermal recovery factors in excess of 50% are difficult to obtain. Storage efficiency may be dramatically reduced in cases where (i) natural groundwater advection through the BTES removes stored heat, (ii) extensive free convection cells (thermosiphons) are allowed to form, and (iii) poor BTES design results in a high surface area/volume ratio of the array shape, allowing high conductive heat losses. The most efficient array shape will typically be a cylinder with similar dimensions of diameter and depth, preferably with an insulated top surface. Despite the potential for moderate thermal recovery, the sheer volume of thermal storage that the natural geological environment offers can still make BTES a very attractive strategy for seasonal thermal energy storage within a “smart” district heat network, especially when coupled with more efficient surficial engineered dynamic thermal energy stores (DTES).

Crystallization of Amorphous Silicon Thin Films by Microwave Heating

2014 ◽  
Vol 1666 ◽  
Author(s):  
Tomohiko Nakamura ◽  
Shinya Yoshidomi ◽  
Masahiko Hasumi ◽  
Toshiyuki Sameshima ◽  
Tomohisa Mizuno
Keyword(s):  
Thin Films ◽  
Heat Treatment ◽  
Amorphous Silicon ◽  
Microwave Heating ◽  
Volume Ratio ◽  
Heated Sample ◽  
Silicon Thin Films ◽  
Scattering Spectra ◽  
Raman Scattering Spectra ◽  
Si Films

ABSTRACTWe report crystallization of amorphous silicon (a-Si) thin films and improvement of thin film transistors (TFTs) characteristics using 2.45 GHz microwave heating assisted with carbon powders. Undoped 50-nm-thick a-Si films were formed on quartz substrates and heated by microwave irradiation for 2, 3, and 4 min. Raman scattering spectra revealed that the crystalline volume ratio increased to 0.42 for the 4-min heated sample. The dark and photo electrical conductivities measured by Air mass 1.5 at 100 mW/cm2 were 2.6x10-6 and 5.2x10-6 S/cm in the case of 4-min microwave heating followed by 1.3x106-Pa-H2O vapor heat treatment at 260°C for 3 h. N channel polycrystalline silicon TFTs characteristics were improved by the combination of microwave heating with high-pressure H2O vapor heat treatment. The threshold voltage decreased from 5.3 to 4.2 V and the effective carrier mobility increased from 18 to 25 cm2/Vs.

Sign in / Sign up

Export Citation Format

Share Document