scholarly journals Application Properties Analysis as a Dielectric Capacitor of End-of-Life Tire-Reinforced HDPE

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2675 ◽  
Author(s):  
Marc Marín-Genescà ◽  
Jordi García-Amorós ◽  
Ramon Mujal-Rosas ◽  
Lluís Massagués Vidal ◽  
Xavier Colom Fajula
Keyword(s):  
Carbon Black ◽  
End Of Life ◽  
Polymeric Composite ◽  
Interfacial Polarization ◽  
Morphological Properties ◽  
Electrical Behavior ◽  
Scanning Calorimetry ◽  
Low Frequencies ◽  
Vulcanized Rubber ◽  
Different Temperatures

The purpose of the present research is to obtain waste of polymeric composite as an insulator capacitive application. Rubber materials, once they end their useful life, may be difficult to reuse or recycle. At present, research only uses one tire recycling method, which involves grinding and separating steel and fibers from vulcanized rubber, and then using the rubber particles for industrial capacitors. The methodology for this research is to compare the permittivity (ε′ and ε″) between high-density polyethylene (HDPE) and the polymer matrix compound, consisting of an HDPE polymeric matrix blended with end-of-life tire particles (ground tire rubber (GTR)), to analyze the feasibility of using such tires as electrically insulating materials (dielectrics). The incorporation of carbon black in the GTR compounds modifies conductivity; GTRs carry a significant amount of carbon black, and therefore some electrical properties may change significantly compared to highly insulating polymer substrates. The performed experimental study is based on a dynamic electric analysis (DEA) test developed in the frequency range of 10−2 Hz to 3 MHz and at different temperatures (from 35 to 70 °C) of different samples type: HDPE neat and HDPE compounds with 10%, 20% and 40% of GTR loads. A sample’s electrical behavior is checked for its dependence on frequency and temperature, focused on the permittivity property; this is a key property for capacitive insulators and is key for examining the possible applications in this field, for HDPE + GTR blends. Results for the permittivity behavior and the loss factor show different electrical behavior. For a neat HDPE sample, no dependence with frequency nor temperature is shown. However, with the addition of 10%, 20%, and 40% amount of GTR the HDPE compounds show different behaviors: for low frequencies, interfacial polarization relaxation is seen, due to the Maxwell–Wagner–Sillars (MWS) effect, performed in heterogeneous materials. In order to analyze thermal and morphological properties the differential scanning calorimetry (DSC) test and scanning electron microscopy (SEM) have been used. Results obtained show that adding waste tire particles in an HDPE matrix allows HDPE + 40% GTR blends to act as a dielectric in capacitors, increasing the capacitor dielectric efficiency in the low frequencies due to the MWS effect, which increases the dielectric constant.

scholarly journals Study Analysis of Thermal, Dielectric, and Functional Characteristics of an Ethylene Polyethylene Diene Monomer Blended with End-of-Life Tire Microparticles Amounts

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 509
Author(s):  
Marc Marín-Genescà ◽  
Ramon Mujal-Rosas ◽  
Jordi García-Amorós ◽  
Miguel Mudarra ◽  
Xavier Ramis Juan ◽  
...  
Keyword(s):  
End Of Life ◽  
Electric Modulus ◽  
Control Sample ◽  
Interfacial Polarization ◽  
Dielectric Behavior ◽  
Particle Sizes ◽  
Thermal Tests ◽  
Vulcanized Rubber ◽  
Different Types ◽  
Industrial Use

The recycling and disposal of disused tires is a topic of great concern to today’s companies, researchers, and society in general. In this sense, our research aims to recycle end-of-life tires (GTRs) through the separation of the fraction of vulcanized rubber from the other compounds in order to later grind this fraction and separate it into lower particle sizes. Finally, we aim to incorporate these GTR particles as a filler of an ethylene-polyethylene-diene monomer (EPDM). The obtained composites with EPDM and GTR are tested (5%, 10%, 20%) comparing these values with neat EPDM as a control sample. Thermal tests such as differential calorimetry (DSC) and thermogravimetric analysis (TGA) as well as dielectric tests (DEA) are performed in order to characterize these materials and check their viability as dielectric or semiconductor, for industrial use. It is checked how the presence of GTR increases functional properties such as conductivity/permittivity. The influence of temperature (40 to 120 °C) and addition of GTR particles in electrical properties has also been analyzed. The dielectric behavior of these composites is fully characterized, analyzing the different types of relaxation with increasing frequency (10 mHz to 3 MHz), using the electric modulus, and Argand diagrams among other measures. The influence of GTR and temperature in the dielectric and thermal behavior of these materials has been analyzed, where CB of GTR creates interfacial polarization phenomena in the dielectric behavior of the composite and increases the permittivity (real and imaginary) as well as the conductivity. Finally, with these obtained properties, the possible application of EPDM/GTR composites as industrial dielectrics has been studied.

scholarly journals Barrier Properties of GnP–PA-Extruded Films

Polymers ◽  
2020 ◽  
Vol 12 (3) ◽  
pp. 669
Author(s):  
Regine Boldt ◽  
Andreas Leuteritz ◽  
Daniela Schob ◽  
Matthias Ziegenhorn ◽  
Udo Wagenknecht
Keyword(s):  
Filler Content ◽  
Barrier Properties ◽  
Permeation Rate ◽  
Graphene Nanoplatelets ◽  
Laboratory Scale ◽  
Morphological Properties ◽  
Scanning Calorimetry ◽  
Transmission Electron ◽  
Extruded Films ◽  
Different Temperatures

It is generally known that significant improvements in the properties of nanocomposites can be achieved with graphene types currently commercially available. However, so far this is only possible on a laboratory scale. Thus, the aim of this study was to transfer results from laboratory scale experiments to industrial processes. Therefore, nanocomposites based on polyamide (PA) and graphene nanoplatelets (GnP) were prepared in order to produce membranes with improved gas barrier properties, which are characterized by reduced permeation rates of helium. First, nanocomposites were prepared with different amounts of commercial availably graphene nanoplatelets using a semi-industrial-scale compounder. Subsequently, films were produced by compression molding at different temperatures, as well as by flat film extrusion. The extruded films were annealed at different temperatures and durations. In order to investigate the effect of thermal treatment on barrier properties in correlation to thermal, structural, and morphological properties, the films were characterized by differential scanning calorimetry (DSC), wide angle X-ray scattering (WAXS), optical microscopy (OM), transmission electron microscopy (TEM), melt rheology measurements, and permeation measurements. In addition to structural characterization, mechanical properties were investigated. The results demonstrate that the permeation rate is strongly influenced by the processing conditions and the filler content. If the filler content is increased, the permeation rate is reduced. The annealing process can further enhance this effect.

scholarly journals Implications of the Use of Silica as Active Filler in Passenger Car Tire Compounds on Their Recycling Options

Materials ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 725 ◽  
Author(s):  
Johannes van Hoek ◽  
Geert Heideman ◽  
Jacques Noordermeer ◽  
Wilma Dierkes ◽  
Anke Blume
Keyword(s):  
Tensile Strength ◽  
Carbon Black ◽  
End Of Life ◽  
Fuel Economy ◽  
Major Part ◽  
Recent Past ◽  
Passenger Car ◽  
Polymer Molecules ◽  
Vulcanized Rubber ◽  
Vehicle Component

Tires are an important vehicle component, as car handling, safety and fuel economy depend for a major part on the tire composition and construction. As a consequence, tires are improved continuously. The most prominent improvement in the recent past was the use of a silica-silane filler system in passenger car tread compounds, instead of traditionally used carbon black. For recycling and re-use of end-of-life car tire rubber one of the most promising recycling methods is devulcanization: re-plasticizing the vulcanized rubber by selectively breaking the sulfur bridges between the polymer molecules. In the present paper, the influence of silica, which is present in the passenger car tires granulate, on both devulcanization and subsequent revulcanization, is investigated. In a step-wise approach it is shown that the presence of silica influences both devulcanization and revulcanization. The best tensile strength of the revulcanizate, using a carbon-black-based revulcanization formulation, was 5 MPa. This could be improved to 6.5 MPa by using 2.8 phr of 1,3-DiPhenylGuanidine (DPG) in the revulcanization formulation. After addition of a silanization step during revulcanization by adding 3.2 phr bis[3-(TriEthoxySilyl)Propyl] Tetrasulfide (TESPT), a silane, to the formulation, the tensile strength of the revulcanizate was further improved to 8 MPa. With these results it is shown that the silica in the granulate can be used to improve the revulcanization properties. To check the benefits of using pure tire tread material for the devulcanization and subsequent revulcanization, of both a carbon black and a silica-based virgin tread compound, it is shown that a tensile strength of the revulcanizate of 13 MPa can be reached. This shows the potential of devulcanized rubber when the various tire components are separated before whole car tire material is granulated as the beginning of the recycling.

Rheological and Electrical Properties of CB/HDPE Composites

2013 ◽  
Vol 333-335 ◽  
pp. 1872-1875 ◽  
Author(s):  
Xi Liang Chen ◽  
Peng Cui ◽  
Yan Pei Ji
Keyword(s):  
Electrical Properties ◽  
Carbon Black ◽  
High Density Polyethylene ◽  
Particle Concentration ◽  
Percolation Model ◽  
Electrical Behavior ◽  
Low Frequencies ◽  
Strong Shear ◽  
Rheological Percolation ◽  
Properties Of Composites

The rheological and electrical properties of composites formed by filling high density polyethylene (HDPE) with carbon black (CB) were characterized. Nonuniversal electrical behavior was observed with critical exponent t of 2.9 for the composites. The phenomenon was interpreted in terms with tunneling-percolation model. The effects of shearing frequency and particle concentration on the rheological behavior of the composites were investigated. A second plateau of storage modulus and strong shear thinning behavior were observed at low frequencies induced by aggregation of fillers. And the rheological percolation threshold is found to coincide well with the electrical one.

scholarly journals Effect Of Carbon Black Loading On Linear Low-Density Polyethylene Properties

2021 ◽  
Author(s):  
Noora Al-Qahtani ◽  
Maryam Al-Ejji ◽  
Mabrouk Ouederni ◽  
Mariam AlMaadeed ◽  
Nabil Madi
Keyword(s):  
Carbon Black ◽  
Morphological Properties ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Low Frequencies ◽  
Shear Rates ◽  
Carbon Particles ◽  
Mechanical And Electrical Properties ◽  
High Shear Rates

Abstract The mechanical, thermal, electrical, reheology, and morphological properties of composites made from linear low-density polyethylene and carbon black (CB) content of 5%, 10%, and 20% by weight were investigated. The optimum mechanical and electrical properties performance was achieved with the adding of 5% carbon black. The drop in properties after adding more CB is due to agglomeration and poor dispersion of carbon particles in the polymer matrix. CB resulted in higher dynamic viscosity and storage modulus at low frequencies, although this phenomenon was reversed at high frequencies. CB resulted in more shear thinning of LLDPE at high shear rates.

Injectable in-situ Forming Depot Of Doxycycline Hyclate/α-Cyclodextrin Complex using PLGA for Periodontitis Treatment: Preparation, Charac-terization, and In-Vitro Evaluation

2020 ◽  
Vol 17 ◽  
Author(s):  
Elham Khodaverdi ◽  
Farhad Eisvand ◽  
Mohammad Sina Nezami ◽  
Seyedeh Nesa Rezaeian Shiadeh ◽  
Hossein Kamali ◽  
...  
Keyword(s):  
Complex Form ◽  
Docking Studies ◽  
Morphological Properties ◽  
Burst Release ◽  
Cyclodextrin Complex ◽  
Doxycycline Hyclate ◽  
Scanning Calorimetry ◽  
In Situ Forming

Background:: Doxycycline (DOX) is used in treating a bacterial infection, especially for periodontitis treatment. Objective: To reduce irritation of DOX for subgingival administration and increase the chemical stability and against enzy-matic, the complex of α-cyclodextrin with DOX was prepared and loaded into injectable in situ forming implant based on PLGA. Methods:: FTIR, molecular docking studies, X-ray diffraction, and differential scanning calorimetry was performed to char-acterize the DOX/α-cyclodextrin complex. Finally, the in-vitro drug release and modeling, morphological properties, and cellular cytotoxic effects were also evaluated. Results:: The stability of DOX was improved with complex than pure DOX. The main advantage of the complex is the al-most complete release (96.31 ± 2.56 %) of the drug within 14 days of the implant, whereas in the formulation containing the pure DOX and the physical mixture the DOX with α-cyclodextrin release is reached to 70.18 ± 3.61 % and 77.03 ± 3.56 %, respectively. This trend is due to elevate of DOX stability in the DOX/ α-cyclodextrin complex form within PLGA implant that confirmed by the results of stability. Conclusion:: Our results were indicative that the formulation containing DOX/α-cyclodextrin complex was biocompatible and sustained-release with minimum initial burst release.

Characterization of Nostoc muscorum NCCU-442 Derived Poly-3- hydroxybutyrate (PHB) and Polyethylene Glycol (PEG) Blends

2020 ◽  
Vol 10 (3) ◽  
pp. 200-207
Author(s):  
Sabbir Ansari ◽  
Tasneem Fatma
Keyword(s):  
Thermal Properties ◽  
Polyethylene Glycol ◽  
Morphological Properties ◽  
Morphological Alteration ◽  
Nostoc Muscorum ◽  
Microbial Culture ◽  
Polymer Science ◽  
Mixed Microbial Culture ◽  
Scanning Calorimetry ◽  
Casting Technique

Background: Poly-3-hydroxybutyrate (PHB) has attracted much consideration as biodegradable biocompatible polymer. This thermoplastic polymer has comparable material properties to polypropylene. Materials with more valuable properties may result from blending, a common practice in polymer science. Objective: In this paper, blends of PHB (extracted from cyanobacterium Nostoc muscorum NCCU- 442 with polyethylene glycol (PEG) were investigated for their thermal, tensile, hydrophilic and biodegradation properties. Methods: Blends were prepared in different proportions of PHB/PEG viz. 100/0, 98/2, 95/5, 90/10, 80/20, and 70/30 (wt %) using solvent casting technique. Morphological properties were investigated by using Scanning Electron Microscopy (SEM). Differential scanning calorimetry and thermogravimetric analysis were done for thermal properties determination whereas the mechanical and hydrophilic properties of the blends were studied by means of an automated material testing system and contact angle analyser respectively. Biodegradability potential of the blended films was tested as percent weight loss by mixed microbial culture within 60 days. Results: The blends showed good misciblity between PEG and PHB, however increasing concentrations of plasticizer caused morphological alteration as evidenced by SEM micrographs. PEG addition (10 % and above) showed significant alternations in the thermal properties of the blends. Increase in the PEG content increased the elongation at break ratio i.e enhanced the required plasticity of PHB. Rate of microbial facilitated degradation of the blends was greater with increasing PEG concentrations. Conclusion: Blending with PEG increased the crucial polymeric properties of cyanobacterial PHB.

Effects of additives on the cure kinetics of vinyl ester pultrusion resins

2021 ◽  
pp. 002199832110015
Author(s):  
Alexander Vedernikov ◽  
Yaroslav Nasonov ◽  
Roman Korotkov ◽  
Sergey Gusev ◽  
Iskander Akhatov ◽  
...  
Keyword(s):  
Vinyl Ester ◽  
Mean Squared Error ◽  
Cure Kinetics ◽  
Zinc Stearate ◽  
Heating Rates ◽  
Scanning Calorimetry ◽  
Different Temperatures ◽  
Predicted Values ◽  
Kinetics Of ◽  
Final Degree

Pultrusion is a highly efficient composite manufacturing process. To accurately describe pultrusion, an appropriate model of resin cure kinetics is required. In this study, we investigated cure kinetics modeling of a vinyl ester pultrusion resin (Atlac 430) in the presence of aluminum hydroxide (Al(OH)3) and zinc stearate (Zn(C18H35O2)2) as processing additives. Herein, four different resin compositions were studied: neat resin composition, composition with Al(OH)3, composition comprising Zn(C18H35O2)2, and composition containing both Al(OH)3 and Zn(C18H35O2)2. To analyze each composition, we performed differential scanning calorimetry at the heating rates of 5, 7.5, and 10 K/min. To characterize the cure kinetics of Atlac 430, 16 kinetic models were tested, and their performances were compared. The model based on the [Formula: see text]th-order autocatalytic reaction demonstrated the best results, with a 4.5% mean squared error (MSE) between the experimental and predicted data. This study proposes a method to reduce the MSE resulting from the simultaneous melting of Zn(C18H35O2)2. We were able to reduce the MSE by approximately 34%. Numerical simulations conducted at different temperatures and pulling speeds demonstrated a significant influence of resin composition on the pultrusion of a flat laminate profile. Simulation results obtained for the 600 mm long die block at different die temperatures (115, 120, 125, and 130 °C) showed that for a resin with a final degree of cure exceeding 95% at the die exit, the maximum difference between the predicted values of pulling speed for a specified set of compositions may exceed 1.7 times.

scholarly journals Rheological, Thermal, Superficial, and Morphological Properties of Thermoplastic Achira Starch Modified with Lactic Acid and Oleic Acid

Molecules ◽  
2019 ◽  
Vol 24 (24) ◽  
pp. 4433 ◽  
Author(s):  
Carolina Caicedo ◽  
Rocío Yaneli Aguirre Loredo ◽  
Abril Fonseca García ◽  
Omar Hernán Ossa ◽  
Aldo Vázquez Arce ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Oleic Acid ◽  
Complex Viscosity ◽  
Thermoplastic Starch ◽  
Residual Energy ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Rheological Analysis ◽  
Acid Agent

The modification of achira starch a thermoplastic biopolymer is shown. Glycerol and sorbitol, common plasticizers, were used in the molten state with organic acids such as oleic acid and lactic acid obtaining thermodynamically more stable products. The proportion of starch:plasticizer was 70:30, and the acid agent was added in portions from 3%, 6%, and 9% by weight. These mixtures were obtained in a torque rheometer for 10 min at 130 °C. The lactic acid managed to efficiently promote the gelatinization process by increasing the available polar sites towards the surface of the material; as a result, there were lower values in the contact angle, these results were corroborated with the analysis performed by differential scanning calorimetry and X-ray diffraction. The results derived from oscillatory rheological analysis had a viscous behavior in the thermoplastic starch samples and with the presence of acids; this behavior favors the transitions from viscous to elastic. The mixture of sorbitol or glycerol with lactic acid promoted lower values of the loss module, the storage module, and the complex viscosity, which means lower residual energy in the transition of the viscous state to the elastic state; this allows the compounds to be scaled to conventional polymer transformation processes.

GDC - Y 2 O 3 Oxide Based Two Phase Nanocomposite Electrolyte

2011 ◽  
Vol 8 (4) ◽  
Author(s):  
Rizwan Raza ◽  
Ghazanfar Abbas ◽  
S. Khalid Imran ◽  
Imran Patel ◽  
Bin Zhu
Keyword(s):  
Fuel Cell ◽  
Ionic Conductivities ◽  
Morphological Properties ◽  
Scanning Calorimetry ◽  
Two Phase ◽  
Composite Electrolyte ◽  
Significant Performance ◽  
Advanced Fuel ◽  
Nanocomposite Electrolyte ◽  
Scherrer Formula

Oxide based two phase composite electrolyte (Ce0.9Gd0.1O2–Y2O3) was synthesized by coprecipitation method. The nanocomposite electrolyte showed the significant performance of power density 785 mW cm−2 and higher conductivities at relatively low temperature 550°C. Ionic conductivities were measured with ac impedance spectroscopy and four-probe dc method. The structural and morphological properties of the prepared electrolyte were investigated by scanning electron microscope (SEM). The thermal stability was determined with differential scanning calorimetry. The particle size that was calculated with Scherrer formula, 15–20 nm, is in a good agreement with the SEM and X- ray diffraction results. The purpose of this study is to introduce the functional nanocomposite materials for advanced fuel cell technology to meet the challenges of solid oxide fuel cell.

Sign in / Sign up

Export Citation Format

Share Document