scholarly journals 3D Printing PLA Waste to Produce Ceramic Based Particulate Reinforced Composite Using Abundant Silica-Sand: Mechanical Properties Characterization

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2579
Author(s):  
Waleed Ahmed ◽  
Sidra Siraj ◽  
Ali H. Al-Marzouqi
Keyword(s):  
Mechanical Properties ◽  
Composite Material ◽  
3D Printing ◽  
Fused Deposition Modeling ◽  
Testing Machine ◽  
Silica Sand ◽  
Fused Deposition ◽  
Mechanical Properties Characterization ◽  
And Control ◽  
The Impact

Due to the significant properties of silica, thermostatics can be enhanced using silica-additives to maximize the quality of polymer compounds and transform plastics into tailored properties. The silica additives can enhance the handling and quality performance of composites and thermoplastic polymers due to their diverse potential. Besides, using silica as an additive in different characteristics can allow granulates and powders to flow easily, minimize caking, and control rheology. On the other hand, the eruption of 3D printing technology has led to a massive new waste source of plastics, especially the polylactic acid (PLA) that is associated with the fused deposition modeling (FDM) process. In this paper, the impact on the mechanical properties when silica is mixed with waste PLA from 3D printing was studied. The PLA/silica mixtures were prepared using different blends through twin extruders and a Universal Testing Machine was used for the mechanical characterization. The result indicated that increasing silica composition resulted in the increase of the tensile strength to 121.03 MPa at 10 wt%. Similar trends were also observed for the toughness, ductility, and the yield stress values of the PLA/silica blends at 10 wt%, which corresponds to the increased mechanical property of the composite material reinforced by the silica particles. Improvement in the mechanical properties of the developed composite material promotes the effective recycling of PLA from applications such as 3D printing and the potential of reusing it in the same application.

scholarly journals Polymer Composites Used in Rapid Prototyping Technology

2020 ◽  
Vol 44 (1) ◽  
pp. 15-20
Author(s):  
Katarzyna Bulanda ◽  
Mariusz Oleksy ◽  
Rafał Oliwa ◽  
Grzegorz Budzik ◽  
Tadeusz Markowski
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Fused Deposition Modeling ◽  
New Materials ◽  
Fused Deposition ◽  
The Matrix ◽  
Molded Parts ◽  
Deposition Modeling ◽  
Injection Molded ◽  
The Impact

AbstractNew materials and filaments dedicated to 3D printing were obtained using the fused deposition modeling method, and the properties of the produced materials were investigated. Polylactide was used as a polymer base for the assays because of the desired properties of the polymer, mainly biodegradability, and the matrix was refilled by the addition of metallic nanofillers, such as bronze, copper, brass, and steel. For the composites obtained, mechanical properties were investigated to determine the dependence of the obtained results on the content and type of filler used and on the method of fabrication of the fittings. It was found that the additives present in the polymer matrix increased the fluidity of the material. The best results were obtained for the compositions with bronze and steel in which the mass flow rate was 72.97 and 79.99 g/10 min, respectively. The filled material that had lower hardness was measured by Rockwell and the impact strength was measured by Charpy. In addition, it was found that injection-molded parts obtained much better mechanical properties than those obtained by 3D printing.

scholarly journals The impact of process parameters on mechanical properties of parts fabricated in PLA with an open-source 3-D printer

2015 ◽  
Vol 21 (5) ◽  
pp. 604-617 ◽  
Author(s):  
Antonio Lanzotti ◽  
Marzio Grasso ◽  
Gabriele Staiano ◽  
Massimo Martorelli
Keyword(s):  
Mechanical Properties ◽  
Open Source ◽  
Process Parameters ◽  
Computer Aided Design ◽  
Fused Deposition Modeling ◽  
Testing Machine ◽  
Main Process ◽  
Content Type ◽  
Fused Deposition ◽  
The Impact

Purpose – This study aims to quantify the ultimate tensile strength and the nominal strain at break (ɛf) of printed parts made from polylactic acid (PLA) with a Replicating Rapid prototyper (Rep-Rap) 3D printer, by varying three important process parameters: layer thickness, infill orientation and the number of shell perimeters. Little information is currently available about mechanical properties of parts printed using open-source, low-cost 3D printers. Design/methodology/approach – A computer-aided design model of a tensile test specimen was created, conforming to the ASTM:D638. Experiments were designed, based on a central composite design. A set of 60 specimens, obtained from combinations of selected parameters, was printed on a Rep-Rap Prusa I3 in PLA. Testing was performed using a JJ Instruments – T5002-type tensile testing machine and the load was measured using a load cell of 1,100 N. Findings – This study investigated the main impact of each process parameter on mechanical properties and the effects of interactions. The use of a response surface methodology allowed the proposition of an empirical model which connects process parameters and mechanical properties. Even though results showed a high variability, additional ideas on how to understand the impact of process parameters are suggested in this paper. Originality/value – On the basis of experimental results, it is possible to obtain practical suggestions to set common process parameters in relation to mechanical properties. Experiments discussed in the present paper provide a variety of data and insight regarding the relationship among the main process parameters and the stiffness and strength of fused deposition modeling-printed parts made from PLA. In particular, this paper underlines the shortage in existing literature concerning the impact of process parameters on the elastic modulus and the strain to failure for the PLA. The experimental data produced show a good degree of compliance with analytical formulations and other data found in literature.

scholarly journals Research on the Application of MWCNTs/PLA Composite Material in the Manufacturing of Conductive Composite Products in 3D Printing

Micromachines ◽  
2018 ◽  
Vol 9 (12) ◽  
pp. 635 ◽  
Author(s):  
Jinjie Luo ◽  
Haibao Wang ◽  
Duquan Zuo ◽  
Anping Ji ◽  
Yaowen Liu
Keyword(s):  
Composite Material ◽  
3D Printing ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Melt Flow Rate ◽  
Conductive Composites ◽  
Fused Deposition ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

As an advanced manufacturing technology that has been developed in recent years, three-dimensional (3D) printing of macromolecular materials can create complex-shaped components that cannot be realized by traditional processing. However, only a few types of macromolecular materials are suitable for 3D printing: the structure must have a single function, and manufacturing macromolecular functional devices is difficult. In this study, using poly lactic acid (PLA) as a matrix, conductive composites were prepared by adding various contents of multi-walled carbon nanotubes (MWCNTs). The printability and properties of MWCNT/PLA composites with different MWCNT proportions were studied by using the fused deposition modeling (FDM) processing technology of 3D printing. The experimental results showed that high conductivity can be realized in 3D-printed products with a composite material containing 5% MWCNTs; its conductivity was 0.4 ± 0.2 S/cm, its tensile strength was 78.4 ± 12.4 MPa, and its elongation at break was 94.4% ± 14.3%. It had a good melt flow rate and thermal properties, and it enabled smooth printing, thus meeting all the requirements for the 3D printing of consumables.

Mechanical Properties of PVC/ABS Composite Material

2011 ◽  
Vol 217-218 ◽  
pp. 1170-1173
Author(s):  
Wei Wei Qiao ◽  
Hui Wang ◽  
Yan Hua Zhao ◽  
Yi Xia Han
Keyword(s):  
Mechanical Properties ◽  
Composite Material ◽  
Testing Machine ◽  
Impact Testing ◽  
Elongation At Break ◽  
Poly Vinyl Chloride ◽  
Maximum Value ◽  
Material Testing Machine ◽  
The Impact ◽  
Butadiene Styrene

We investigate the mechanical properties of Poly Vinyl Chloride (PVC)/ acrylnitrile-butadiene-styrene copolymer (ABS) composite material with an impact testing machine，a material testing machine and other accessory devices. The result shows that the mechanical properties of PVC/ABS composite are a function of composition, the addition of ABS improved the mechanical properties of PVC/ ABS composite，the impact strength and elongation at break rise significantly with increasing ABS content in PVC/ABS composite and appears maximum value，While the tensile strength and modulus almost decrease monotonously with increasing ABS content in PVC/ABS composite.

scholarly journals Proper Blends of Biodegradable Polycaprolactone and Natural Rubber for 3D Printing

Polymers ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 2416
Author(s):  
Thossapit Wissamitanan ◽  
Charoenyutr Dechwayukul ◽  
Ekwipoo Kalkornsurapranee ◽  
Wiriya Thongruang
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Natural Rubber ◽  
Shape Recovery ◽  
Fused Deposition Modeling ◽  
Melt Flow ◽  
Melt Flow Rate ◽  
Fused Deposition ◽  
Compression Set ◽  
Deposition Modeling

Flexible thermoplastic elastomers (TPE) were prepared for fused deposition modeling (FDM) or 3D printing. These materials can be used for medical purposes such as disposable soft splints and other flexible devices. Blends of 50% epoxidized natural rubber (ENR-50) and block rubber (Standard Thai Rubber 5L (STR5L)) with polycaprolactone (PCL) were produced and compared. The purpose of this study was to investigate the properties of natural rubber (NR) and PCL in simple blends with PCL contents of 40%, 50%, and 60% by weight (except at 75% for morphology study) in the base mixture (NR/PCL). The significant flow factors for FDM materials, such as melting temperature (Tm) and melt flow rate (MFR), were observed by differential scanning calorimetry (DSC) and via the melt flow index (MFI). In addition, the following mechanical properties were also determined: tensile strength, compression set, and hardness. The results from DSC showed that the melting temperature changed slightly (1–2 °C) with amount of PCL used, and there was a suspicious point in the 50/50 blends with both types of rubber. The lowest melting enthalpy of both blends was found at the 50/50 blended composition. The MFI results showed that PCL significantly affected the melt flow rate of both blends. The ENR-50/PCL blend flowed better than the STR5L/PCL blend. The conclusion was that this was due to the morphology of its phase structure having better uniformity than that of the STR5L/PCL blend. In compression set testing or measuring shape recovery, rubber directly influenced the recovery in all blends. The ENR-50/PCL blend had less recovery than the STR5L/PCL blend, probably due to the functional effects of epoxide groups and polarity mismatch. The hard phase PCL significantly affected the hardness of samples but improved shape recovery of the material. The ENR-50/PCL blend had better tensile properties than the STR5L/PCL blend. The elongation at break of both blends improved with a high rubber content. Hence, the ENR-50/PCL blend was superior to STR5L/PCL for printing purposes due to its better miscibility, uniformity, and flow, which are the keys to success for optimizing the fused deposition modeling conditions as well as the overall mechanical properties of products. Most blends in this study were only slightly different, but the 50/50 blend of ENR-50/PCL seemed to be near optimal for 3D printing.

Effect of layer thickness on irreversible thermal expansion and interlayer strength in fused deposition modeling

2017 ◽  
Vol 23 (5) ◽  
pp. 943-953 ◽  
Author(s):  
Anthony A. D’Amico ◽  
Analise Debaie ◽  
Amy M. Peterson
Keyword(s):  
Mechanical Properties ◽  
Thermal Expansion ◽  
Flexural Strength ◽  
Layer Thickness ◽  
Fused Deposition Modeling ◽  
Thermal Strain ◽  
Content Type ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
The Impact

Purpose The aim of this paper is to examine the impact of layer thickness on irreversible thermal expansion, residual stress and mechanical properties of additively manufactured parts. Design/methodology/approach Samples were printed at several layer thicknesses, and their irreversible thermal expansion, tensile strength and flexural strength were determined. Findings Irreversible thermal strain increases with decreasing layer thickness, up to 22 per cent strain. Tensile and flexural strengths exhibited a peak at a layer thickness of 200 μm although the maximum was not statistically significant at a 95 per cent confidence interval. Tensile strength was 54 to 97 per cent of reported values for injection molded acrylonitrile butadiene styrene (ABS) and 29 to 73 per cent of those reported for bulk ABS. Flexural strength was 18 to 41 per cent of reported flexural strength for bulk ABS. Practical implications The large irreversible thermal strain exhibited that corresponding residual stresses could lead to failure of additively manufactured parts over time. Additionally, the observed irreversible thermal strains could enable thermally responsive shape in additively manufactured parts. Variation in mechanical properties with layer thickness will also affect manufactured parts. Originality/value Tailorable irreversible thermal strain of this magnitude has not been previously reported for additively manufactured parts. This strain occurs in parts made with both high-end and consumer grade fused deposition modeling machines. Additionally, the impact of layer thickness on tensile and flexural properties of additively manufactured parts has received limited attention in the literature.

scholarly journals Determining the parameters for a 3D-printing process using the fused deposition modeling in order to manufacture an article with the required structural parameters

2021 ◽  
Vol 2 (1 (110)) ◽  
pp. 70-80
Author(s):  
Oleksii Vambol ◽  
Andrii Kondratiev ◽  
Svitlana Purhina ◽  
Maryna Shevtsova
Keyword(s):  
3D Printing ◽  
Fused Deposition Modeling ◽  
Structural Parameters ◽  
Technological Parameters ◽  
Non Linear Programming ◽  
Fused Deposition ◽  
Elasticity Module ◽  
Deposition Modeling ◽  
The Impact ◽  
Printing Parameters

The mass application of FDM technology is slowed down due to the difficulty of selecting 3D printing parameters in order to manufacture an article with the required characteristics. This paper reports a study into the impact of 3D printing parameters (temperature, print speed, layer height) on mechanical parameters (strength, elasticity module), as well as on the accuracy of printing and roughness of the surface of a specimen based on thermoplastic (PLA plastic). Several batches of specimens were fabricated for this study in accordance with ASTM D638 and ASTM D695, which were tested for tension, geometric accuracy, and roughness. Based on the experimental data, regression analysis was carried out and the functional dependences of the strength, elasticity module, printing precision, roughness of a surface on 3D printing parameters (temperature, speed, thickness of the layer) were constructed. In addition, the derived mathematical model underlying a method of non-linear programming has established such printing parameters that could provide for the required properties of a structure. The analytical dependences reported in the current work demonstrate a high enough determination factor in the examined range of parameters. Using functional dependences during the design phase makes it possible to assess the feasibility of its manufacture with the required properties, reduce the time to work out the process of printing it, and give recommendations on the technological parameters of 3D printing. The recommendations from this study could be used to make PLA-plastic articles for various purposes with the required properties

scholarly journals Parameters Affecting the Mechanical Properties of Three-Dimensional (3D) Printed Carbon Fiber-Reinforced Polylactide Composites

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2456
Author(s):  
Demei Lee ◽  
Guan-Yu Wu
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
3D Printing ◽  
Three Dimensional ◽  
Fused Deposition Modelling ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Bed Temperature ◽  
3D Printed ◽  
The Impact

Three-dimensional (3D) printing is a manufacturing technology which creates three-dimensional objects layer-by-layer or drop-by-drop with minimal material waste. Despite the fact that 3D printing is a versatile and adaptable process and has advantages in establishing complex and net-shaped structures over conventional manufacturing methods, the challenge remains in identifying the optimal parameters for the 3D printing process. This study investigated the influence of processing parameters on the mechanical properties of Fused Deposition Modelling (FDM)-printed carbon fiber-filled polylactide (CFR-PLA) composites by employing an orthogonal array model. After printing, the tensile and impact strengths of the printed composites were measured, and the effects of different parameters on these strengths were examined. The experimental results indicate that 3D-printed CFR-PLA showed a rougher surface morphology than virgin PLA. For the variables selected in this analysis, bed temperature was identified as the most influential parameter on the tensile strength of CFR-PLA-printed parts, while bed temperature and print orientation were the key parameters affecting the impact strengths of printed composites. The 45° orientation printed parts also showed superior mechanical strengths than the 90° printed parts.

Finite Element Analysis of Additive Manufacturing Based on Fused Deposition Modeling: Distortions Prediction and Comparison With Experimental Data

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
Alberto Cattenone ◽  
Simone Morganti ◽  
Gianluca Alaimo ◽  
Ferdinando Auricchio
Keyword(s):  
Additive Manufacturing ◽  
3D Printing ◽  
Fused Deposition Modeling ◽  
Step Size ◽  
Time Step ◽  
Time Step Size ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
The Impact ◽  
Functional Components

Additive manufacturing (or three-dimensional (3D) printing) is constantly growing as an innovative process for the production of complex-shape components. Among the seven recognized 3D printing technologies, fused deposition modeling (FDM) covers a very important role, not only for producing representative 3D models, but, mainly due to the development of innovative material like Peek and Ultem, also for realizing structurally functional components. However, being FDM a production process involving high thermal gradients, non-negligible deformations and residual stresses may affect the 3D printed component. In this work we focus on meso/macroscopic simulations of the FDM process using abaqus software. After describing in detail the methodological process, we investigate the impact of several parameters and modeling choices (e.g., mesh size, material model, time-step size) on simulation outcomes and we validate the obtained results with experimental measurements.

Sign in / Sign up

Export Citation Format

Share Document