scholarly journals Experimental and Numerical Analysis for the Mechanical Characterization of PETG Polymers Manufactured with FDM Technology under Pure Uniaxial Compression Stress States for Architectural Applications

Polymers ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 2202
Author(s):  
Jorge Manuel Mercado-Colmenero ◽  
M. Dolores La Rubia ◽  
Elena Mata-Garcia ◽  
Moises Rodriguez-Santiago ◽  
Cristina Martin-Doñate
Keyword(s):  
Uniaxial Compression ◽  
Fused Deposition Modeling ◽  
Mechanical Characterization ◽  
Plastic Material ◽  
Compression Modulus ◽  
Simulation Software ◽  
Experimental Results ◽  
Structural Part ◽  
Fused Deposition ◽  
Printing Direction

This paper presents the numerical and experimental analysis performed on the polymeric material Polyethylene Terephthalate Glycol (PETG) manufactured with Fused Deposition Modeling Technology (FDM) technology, aiming at obtaining its mechanical characterization under uniaxial compression loads. Firstly, with the objective of evaluating the printing direction that poses a greater mechanical strength, eighteen test specimens were manufactured and analyzed according to the requirements of the ISO-604 standards. After that, a second experimental test analyzed the mechanical behavior of an innovative structural design manufactured in Z and X–Y directions under uniaxial compression loads according to the requirements of the Spanish CTE standard. The experimental results point to a mechanical linear behavior of PETG in X, Y and Z manufacturing directions up to strain levels close to the yield strength point. SEM micrographs show different structural failures linked to the specimen manufacturing directions. Test specimens manufactured along X present a brittle fracture caused by a delamination process. On the contrary, test specimens manufactured along X and Y directions show permanent plastic deformations, great flexibility and less strength under compression loads. Two numerical analyses were performed on the structural part using Young’s compression modulus obtained from the experimental tests and the load specifications required for the Spanish CTE standards. The comparison between numerical and experimental results presents a percentage of relative error of 2.80% (Z-axis), 3.98% (X-axis) and 3.46% (Y-axis), which allows characterizing PETG plastic material manufactured with FDM as an isotropic material in the numerical simulation software without modifying the material modeling equations in the data software. The research presented here is of great help to researchers working with polymers and FDM technology for companies that might need to numerically simulate new designs with the PETG polymer and FDM technology.

scholarly journals Analysis of the Influencing Factors of FDM-Supported Positions for the Compressive Strength of Printing Components

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4008
Author(s):  
Zhengkai Feng ◽  
Heng Wang ◽  
Chuanjiang Wang ◽  
Xiujuan Sun ◽  
Shuai Zhang
Keyword(s):  
Compressive Strength ◽  
Stress Intensity ◽  
Influencing Factors ◽  
Fused Deposition Modeling ◽  
Experimental Results ◽  
Compression Tests ◽  
Suspended State ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Reference Experiment

Fused deposition modeling (FDM) has the advantage of being able to process complex workpieces with relatively simple operations. However, when processing complex components in a suspended state, it is necessary to add support parts to be processed and formed, which indicates an excessive dependence on support. The stress intensity of the supported positions of the printing components can be modified by changing the supporting model of the parts, their density, and their distance in relation to the Z direction in the FDM printing settings. The focus of the present work was to study the influences of these three modified factors on the stress intensity of the supporting position of the printing components. In this study, 99 sets of compression tests were carried out using a position of an FDM-supported part, and the experimental results were observed and analyzed with a 3D topographic imager. A reference experiment on the anti-pressure abilities of the printing components without support was also conducted. The experimental results clarify how the above factors can affect the anti-pressure abilities of the supporting positions of the printing components. According to the results, when the supporting density is 30% and the supporting distance in the Z direction is Z = 0.14, the compressive strength of the printing component is lowest. When the supporting density of the printing component is ≤30% and the supporting distance in the Z direction is Z ≥ 0.10, the compressive strength of printing without support is greater than that of the linear support model. Under the same conditions, the grid-support method offers the highest compressive strength.

scholarly journals Load Distribution on PET-G 3D Prints of Honeycomb Cellular Structures under Compression Load

Polymers ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 1983
Author(s):  
Olimpia Basurto-Vázquez ◽  
Elvia P. Sánchez-Rodríguez ◽  
Graham J. McShane ◽  
Dora I. Medina
Keyword(s):  
Fused Deposition Modeling ◽  
Structural Characteristics ◽  
Honeycomb Structure ◽  
Cellular Structures ◽  
Displacement Curve ◽  
Compression Tests ◽  
Compression Load ◽  
Fused Deposition ◽  
3D Printed ◽  
Printing Direction

Energy resulting from an impact is manifested through unwanted damage to objects or persons. New materials made of cellular structures have enhanced energy absorption (EA) capabilities. The hexagonal honeycomb is widely known for its space-filling capacity, structural stability, and high EA potential. Additive manufacturing (AM) technologies have been effectively useful in a vast range of applications. The evolution of these technologies has been studied continuously, with a focus on improving the mechanical and structural characteristics of three-dimensional (3D)-printed models to create complex quality parts that satisfy design and mechanical requirements. In this study, 3D honeycomb structures of novel material polyethylene terephthalate glycol (PET-G) were fabricated by the fused deposition modeling (FDM) method with different infill density values (30%, 70%, and 100%) and printing orientations (edge, flat, and upright). The effectiveness for EA of the design and the effect of the process parameters of infill density and layer printing orientation were investigated by performing in-plane compression tests, and the set of parameters that produced superior results for better EA was determined by analyzing the area under the curve and the welding between the filament layers in the printed object via FDM. The results showed that the printing parameters implemented in this study considerably affected the mechanical properties of the 3D-printed PET-G honeycomb structure. The structure with the upright printing direction and 100% infill density exhibited an extension to delamination and fragmentation, thus, a desirable performance with a long plateau region in the load–displacement curve and major absorption of energy.

scholarly journals Process Parameter Optimization in Fused Deposition Modeling (FDM) Using Response Surface Methodology (RSM)

2020 ◽  
Author(s):  
Muhammad Salman Mustafa ◽  
Muhammad Qasim Zafar ◽  
Muhammad Arslan Muneer ◽  
Muhammad Arif ◽  
Farrukh Arsalan Siddiqui ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Response Surface Methodology ◽  
Impact Strength ◽  
Response Surface ◽  
Layer Thickness ◽  
Fused Deposition Modeling ◽  
Experimental Results ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Printing Parameters

Abstract Fused Deposition Modeling (FDM) is a widely adopted additive manufacturing process to produce complex 3D structures and it is typically used in the fabrication of biodegradable materials e.g. PLA/PHA for biomedical applications. However, FDM as a fabrication process for such material needs to be optimized to enhance mechanical properties. In this study, dogbone and notched samples are printed with the FDM process to determine optimum values of printing parameters for superior mechanical properties. The effect of layer thickness, infill density, and print bed temperature on mechanical properties is investigated by applying response surface methodology (RSM). Optimum printing parameters are identified for tensile and impact strength and an empirical relation has been formulated with response surface methodology (RSM). Furthermore, the analysis of variance (ANOVA) was performed on the experimental results to determine the influence of the process parameters and their interactions. ANOVA results demonstrate that 44.7% infill density, 0.44 mm layer thickness, and 20C° printing temperatures are the optimum values of printing parameters owing to improved tensile and impact strength respectively. The experimental results were found in strong agreement with the predicted theoretical results.

scholarly journals Mechanical Characterization of the Plastic Material GF-PA6 Manufactured Using FDM Technology for a Compression Uniaxial Stress Field via an Experimental and Numerical Analysis

Polymers ◽  
2020 ◽  
Vol 12 (1) ◽  
pp. 246 ◽  
Author(s):  
Jorge Manuel Mercado-Colmenero ◽  
Cristina Martin-Doñate ◽  
Vincenzo Moramarco ◽  
Michele Angelo Attolico ◽  
Gilda Renna ◽  
...  
Keyword(s):  
Numerical Analysis ◽  
Stress Field ◽  
Experimental Test ◽  
Plastic Material ◽  
Uniaxial Stress ◽  
Experimental Results ◽  
Structural Behavior ◽  
Elastic Behavior ◽  
Fused Deposition ◽  
Industrial Part

This manuscript presents an experimental and numerical analysis of the mechanical structural behavior of Nylstrong GF-PA6, a plastic material manufactured using FDM (fused deposition modeling) technology for a compression uniaxial stress field. Firstly, an experimental test using several test specimens fabricated in the Z and X-axis allows characterizing the elastic behavior of the reinforced GF-PA6 according to the ISO 604 standard for uniaxial compression stress environments in both Z and X manufacturing orientations. In a second stage, an experimental test analyzes the structural behavior of an industrial part manufactured under the same conditions as the test specimens. The experimental results for the test specimens manufactured in the Z and X-axis present differences in the stress-strain curve. Z-axis printed elements present a purely linear elastic behavior and lower structural integrity, while X-axis printed elements present a nonlinear elastic behavior typical of plastic and foam materials. In order to validate the experimental results, numerical analysis for an industrial part is carried out, defining the material GF-PA6 as elastic and isotropic with constant Young’s compression modulus according to ISO standard 604. Simulations and experimental tests show good accuracy, obtaining errors of 0.91% on the Z axis and 0.56% on the X-axis between virtual and physical models.

scholarly journals On the Feasibility of Printing 3D Composite Objects Based on Polypropylene/Multi-walled Carbon Nanotubes

2019 ◽  
Vol 290 ◽  
pp. 03017 ◽  
Author(s):  
Nicoleta-Violeta Stanciu ◽  
Felicia Stan ◽  
Catalin Fetecau ◽  
Florin Susac
Keyword(s):  
Fused Deposition Modeling ◽  
Mechanical Performance ◽  
Extrusion Process ◽  
Flow Activation Energy ◽  
Fused Deposition ◽  
Multi Walled Carbon Nanotubes ◽  
3D Composite ◽  
Trial And Error Method ◽  
Walled Carbon Nanotubes ◽  
Printing Direction

In this paper, the feasibility of 3D printing polypropylene/ multi-walled carbon nanotube (PP/MWCNT) composites by fused deposition modeling. First, the rheological behavior of PP with 0.3, 0.5 and 1 wt.% of MWCNT was investigated in order to determine the printability in terms of melt shear viscosity and flow activation energy. Second, the filament extrusion process was optimized by the trial-and-error method in order to obtain round and constant filaments. Finally, tensile specimens were printed and tested in order to determine the mechanical properties at various printing direction. Experimental results show that the PP/MWCNT composite filaments with MWCNT loading up to 1 wt.% have good printability characteristics and can be successfully 3D printed with good mechanical performance.

Quasi-Static Characterization of Polyamide-Based Discontinuous CFRP Manufactured by Additive Manufacturing and Injection Molding

2019 ◽  
Vol 809 ◽  
pp. 386-391 ◽  
Author(s):  
Patrick Striemann ◽  
Daniel Hülsbusch ◽  
Michael Niedermeier ◽  
Frank Walther
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Injection Molding ◽  
Mechanical Characterization ◽  
Length Distribution ◽  
Deep Understanding ◽  
Raw Material ◽  
Void Content ◽  
Fused Deposition ◽  
Printing Direction

Generating serial components via additive manufacturing (AM) a deep understanding of process-related characteristics is necessary. The extrusion-based AM called fused layer manufacturing (FLM), also known as fused deposition modeling (FDM™) or fused filament fabrication (FFF) is an AM process for producing serial components. Improving mechanical properties of AM parts is done by adding fibers in the raw material to reinforce the polymer. The study aims to create a more detailed comprehension of FLM and process-related characteristics with their influence on the composite.Thereby, a short carbon fiber-reinforced polyamide (CarbonX™ Nylon, 3DXTECH, USA) with 12.5 wt.‑% fiber content, 7 μm fiber diameter, and 150 to 400 µm fiber length distribution was investigated. To separate process-related characteristics of FLM, reference specimens were fabricated via injection molding (IM) with single-batch material. For the mechanical characterization, quasi-static tensile tests were carried out in accordance to DIN 527‑2. Quality assessment including void content and void distribution was performed via micro-computed tomography (CT).The mechanical characterization clarifies effects on mechanical properties depending on process-related characteristics of FLM. CT scans show higher void contents of FLM specimens compared to IM specimens and void orientation dependent on printing direction. FLM shows process-related characteristics which generally strengthen mechanical properties of polymers. Nevertheless, tensile strength of FLM specimens decrease by more than 28% compared to quasi-homogenous IM specimens.

Economic Efficiency of Using Rapid Prototyping Technology

2013 ◽  
Vol 371 ◽  
pp. 210-214 ◽  
Author(s):  
Cristina Gavrus
Keyword(s):  
Rapid Prototyping ◽  
Economic Efficiency ◽  
Fused Deposition Modeling ◽  
Plastic Material ◽  
New Technology ◽  
Point Of View ◽  
Fused Deposition ◽  
Small Series ◽  
Deposition Modeling ◽  
Working Principle

The present paper approaches the issue of using the new technology of Rapid Prototyping [1,2] in product engineering and tries to demonstrate its economic efficiency from the point of view of costs, in comparison with other technologies [. The comparison is made between Rapid Prototyping and plastic material injection. Rapid Prototyping is used for obtaining some prototypes but it also can be successfully used for individual or small series production. The background of the work briefly presented in this paper is related to some experimental research developed by the author regarding Rapid Prototyping Technologies for certain products which are belt pulleys. After the products have been physically created using Rapid Prototyping Technologies, the author was interested in quantifying its economic efficiency. The belt pulley the present paper refers to was obtained by using the Rapid Prototyping Technology FDM (Fused Deposition Modeling [).The working principle of this technology is briefly described later in this paper. As a novelty, the present paper is aiming at determining a criterion that allows a company to choose between the two technologies mentioned above.

Deposition Strategies and Resulting Part Stiffnesses in Fused Deposition Modeling

1999 ◽  
Vol 121 (1) ◽  
pp. 93-103 ◽  
Author(s):  
P. Kulkarni ◽  
D. Dutta
Keyword(s):  
Analytical Model ◽  
Fused Deposition Modeling ◽  
Experimental Results ◽  
Fused Deposition ◽  
Deposition Modeling

In the Fused Deposition Modeling (FDM) process, the choice of deposition strategy plays an important role. In this paper, the effects of different deposition paths on this deposition based LM process are investigated. Some variations on the current deposition strategies are also proposed. The stiffness of parts manufactured by the different strategies is experimentally determined. It is then compared with an analytical model developed using laminate analysis. A good conformance of the laminate model to the experimental results suggests that the laminate model can be used as a design aide to help the designer tailor the deposition strategy to the stiffness requirements.

Sign in / Sign up

Export Citation Format

Share Document