scholarly journals Effect of Chitin Nanocrystals on Crystallization and Properties of Poly(lactic acid)-Based Nanocomposites

Polymers ◽  
2020 ◽  
Vol 12 (3) ◽  
pp. 726 ◽  
Author(s):  
Shikha Singh ◽  
Mitul Patel ◽  
Daniel Schwendemann ◽  
Marta Zaccone ◽  
Shiyu Geng ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Hydrolytic Degradation ◽  
Barrier Properties ◽  
Poly Lactic Acid ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nucleation Effect ◽  
Triethyl Citrate ◽  
Different Temperatures ◽  
Crystallite Sizes

The crystalline phase of poly(lactic acid) (PLA) has crucial effects on its own properties and nanocomposites. In this study, the isothermal crystallization of PLA, triethyl citrate-plasticized PLA (PLA–TEC), and its nanocomposite with chitin nanocrystals (PLA–TEC–ChNC) at different temperatures and times was investigated, and the resulting properties of the materials were characterized. Both PLA and PLA–TEC showed extremely low crystallinity at isothermal temperatures of 135, 130, 125 °C and times of 5 or 15 min. In contrast, the addition of 1 wt % of ChNCs significantly improved the crystallinity of PLA under the same conditions owing to the nucleation effect of the ChNCs. The samples were also crystallized at 110 °C to reach their maximal crystallinity, and PLA–TEC–ChNC achieved 48% crystallinity within 5 min, while PLA and PLA–TEC required 40 min to reach a similar level. Moreover, X-ray diffraction analysis showed that the addition of ChNCs resulted in smaller crystallite sizes, which further influenced the barrier properties and hydrolytic degradation of the PLA. The nanocomposites had considerably lower barrier properties and underwent faster degradation compared to PLA–TEC110. These results confirm that the addition of ChNCs in PLA leads to promising properties for packaging applications.

Plasticizing effects of citrate esters on properties of poly(lactic acid)

2016 ◽  
Vol 36 (4) ◽  
pp. 371-380 ◽  
Author(s):  
Mounira Maiza ◽  
Mohamed Tahar Benaniba ◽  
Valérie Massardier-Nageotte
Keyword(s):  
Differential Scanning Calorimetry ◽  
Lactic Acid ◽  
Mechanical Analysis ◽  
Poly Lactic Acid ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Intermolecular Hydrogen Bonds ◽  
X Ray ◽  
Triethyl Citrate ◽  
Acetyl Tributyl Citrate

Abstract Triethyl citrate (TEC) and acetyl tributyl citrate (ATBC) were used as plasticizer for poly(lactic acid) (PLA). The treated and plasticized PLA at various concentrations were analyzed by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy and opacity. DSC was used to evaluate the crystallinity and thermal property of all the samples. It was found that the glass transition temperature (Tg) and the melting temperature (Tm) decreased as the amount of citrate esters increased. Additionally, the presence of TEC or ATBC tended to increase the crystallinity of PLA. This result was supported by XRD. DMA of plasticized PLA indicates that a decrease in Tg is obtained with increasing plasticizer content. FTIR spectra indicate that there are some molecular interactions by intermolecular hydrogen bonds between PLA and citrate esters. The effect of the concentration of plasticizer on the opacity of the films was negligible.

scholarly journals Structural and morphological characterization of rare earth modified lead titanate

Cerâmica ◽  
2007 ◽  
Vol 53 (328) ◽  
pp. 422-447
Author(s):  
F. C. D. Lemos ◽  
D. M. A. Melo ◽  
P. S. de Lima ◽  
C. A. Paskocimas ◽  
E. Longo ◽  
...  
Keyword(s):  
Rare Earth ◽  
Lead Titanate ◽  
Pechini Method ◽  
Morphological Characterization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Different Temperatures ◽  
Crystallite Sizes ◽  
Modifier Cation

Rare earth modified lead titanate powders Pb1-xRExTiO3 (REPT), x = 0.01, 0.05, 0.07 and RE = Yb, Y, were prepared by the Pechini method. The materials were calcined under flowing oxygen at different temperatures from 300 to 700 ºC. Nanostructured REPT were investigated using X-ray diffraction, scanning electron microscopy and surface area analysis (BET). The results suggest that the modifier cation incorporated into the system has notable influence in the microstructure and a notable decrease in the crystallite sizes.

scholarly journals Hemp Fibre Reinforced Poly(Lactic Acid) Composites

2007 ◽  
Vol 29-30 ◽  
pp. 337-340 ◽  
Author(s):  
M.A. Sawpan ◽  
K.L. Pickering ◽  
Alan Fernyhough
Keyword(s):  
Lactic Acid ◽  
Degree Of Crystallinity ◽  
Poly Lactic Acid ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Hemp Fibre ◽  
Reinforcing Material ◽  
Fibre Loading ◽  
The Degree Of Crystallinity

The potential of hemp fibre as a reinforcing material for Poly(lactic acid) (PLA) was investigated. Good interaction between hemp fibre and PLA resulted in increases of 100% for Young’s modulus and 30% for tensile strength of composites containing 30 wt% fibre. Different predictive ‘rule of mixtures’ models (e.g. Parallel, Series and Hirsch) were assessed regarding the dependence of tensile properties on fibre loading. Limited agreement with models was observed. Differential scanning calorimetry (DSC) and x-ray diffraction (XRD) studies showed that hemp fibre increased the degree of crystallinity in PLA composites.

Characterization of Electrospun Poly(Lactic Acid)/polyaniline Blend Nanofibers

2011 ◽  
Vol 332-334 ◽  
pp. 317-320 ◽  
Author(s):  
Hui Qin Zhang
Keyword(s):  
Lactic Acid ◽  
Composite Nanofibers ◽  
Weight Ratio ◽  
Electrospinning Process ◽  
Poly Lactic Acid ◽  
X Ray Diffraction ◽  
Sem Images ◽  
X Ray ◽  
Ft Ir

In this study, composite nanofibers of polyaniline doped with dodecylbenzene sulfonic acid (PANI-DBSA) and Poly(lactic acid) (PLA) were prepared via an electrospinning process. The surface morphology, thermal properties and crystal structure of PLA/PANI-DBSA nanofibers are characterized using Fourier transform infrared spectroscopy (FT-IR), wide-angle x-ray diffraction (WAXD) and scanning electron microscopy (SEM). SEM images showed that the morphology and diameter of the nanofibers were affected by the weight ratio of blend solution.

X-ray diffraction Warren–Averbach mullite analysis in whiteware porcelains: influence of kaolin raw material

Clay Minerals ◽  
2018 ◽  
Vol 53 (3) ◽  
pp. 471-485 ◽  
Author(s):  
Angel Sanz ◽  
Joaquín Bastida ◽  
Angel Caballero ◽  
Marek Kojdecki
Keyword(s):  
Crystallite Size ◽  
Firing Temperature ◽  
Microstructural Analysis ◽  
Stoichiometric Composition ◽  
Raw Material ◽  
Size Distributions ◽  
X Ray Diffraction ◽  
X Ray ◽  
Different Temperatures ◽  
Crystallite Sizes

ABSTRACTCompositional and microstructural analysis of mullites in porcelain whitewares obtained by the firing of two blends of identical triaxial composition using a kaolin B consisting of ‘higher-crystallinity’ kaolinite or a finer halloysitic kaolin M of lower crystal order was performed. No significant changes in the average Al2O3 contents (near the stoichiometric composition 3:2) of the mullites were observed. Fast and slow firing at the same temperature using B or M kaolin yielded different mullite contents. The Warren–Averbach method showed increase of the D110 mullite crystallite size and crystallite size distributions with small shifts to greater values with increasing firing temperature for the same type of firing (slow or fast) using the same kaolin, as well as significant differences between fast and slow firing of the same blend at different temperatures for each kaolin. The higher maximum frequency distribution of crystallite size observed at the same firing temperature using blends with M kaolin suggests a clearer crystallite growth of mullite in this blend. The agreement between thickening perpendicular to prism faces and mean crystallite sizes <D110> of mullite were not always observed because the direction perpendicular to 110 planes is not preferred for growth.

Crystallization Properties of Nucleated Poly(lactic acid)

2012 ◽  
Vol 549 ◽  
pp. 322-326 ◽  
Author(s):  
Yong Chen ◽  
Qiang Dou
Keyword(s):  
Lactic Acid ◽  
Crystallization Behavior ◽  
Polarized Light ◽  
Nucleating Agent ◽  
Poly Lactic Acid ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Crystallization Properties ◽  
Melting And Crystallization

The effect of a nucleating agent (NT-C) on the crystallization behavior of poly(lactic acid) (PLA) was studied. The melting and crystallization behavior and spherulitic morphology of the nucleated PLA were investigated by means of differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD) and polarized light microscopy (PLM). It is found that the crystallization temperature and crystallinity increase, the spherulitic size decrease for the nucleated PLA. But the crystal structure of the nucleated PLA is not changed.

scholarly journals Composites Based on Poly(Lactic Acid) (PLA) and SBA-15: Effect of Mesoporous Silica on Thermal Stability and on Isothermal Crystallization from Either Glass or Molten State

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2743
Author(s):  
Tamara M. Díez-Rodríguez ◽  
Enrique Blázquez-Blázquez ◽  
Ernesto Pérez ◽  
María L. Cerrada
Keyword(s):  
Lactic Acid ◽  
Mesoporous Silica ◽  
Isothermal Crystallization ◽  
Physical Aging ◽  
Glassy State ◽  
Poly Lactic Acid ◽  
Molten State ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray

Several composites based on an L-rich poly(lactic acid) (PLA) with different contents of mesoporous Santa Barbara Amorphous (SBA-15) silica were prepared in order to evaluate the effect of the mesoporous silica on the resultant PLA materials by examining morphological aspects, changes in PLA phases and their transitions, and, primarily, the influence on some final properties. Melt extrusion was chosen for the obtainment of the composites, followed by quenching from the melt to prepare films. Completely amorphous samples were then attained, as deduced from X-ray diffraction and differential scanning calorimetry (DSC) analyses. Thermogravimetric analysis (TGA) results demonstrated that the presence of SBA-15 particles in the PLA matrix did not exert any significant influence on the thermal decomposition of these composites. An important nucleation effect of the silica was found in PLA, especially under isothermal crystallization either from the melt or from its glassy state. As expected, isothermal crystallization from the glass was considerably faster than from the molten state, and these high differences were also responsible for a more considerable nucleating role of SBA-15 when crystallizing from the melt. It is remarkable that the PLA under analysis showed very close temperatures for cold crystallization and its subsequent melting. Moreover, the type of developed polymorphs did not accomplish the common rules previously described in the literature. Thus, all the isothermal experiments led to exclusive formation of the α modification, and the observation of the α’ crystals required the annealing for long times at temperatures below 80 °C, as ascertained by both DSC and X-ray diffraction experiments. Finally, microhardness (MH) measurements indicated a competition between the PLA physical aging and the silica reinforcement effect in the as-processed amorphous films. Physical aging in the neat PLA was much more important than in the PLA matrix that constituted the composites. Accordingly, the MH trend with SBA-15 content was strongly dependent on aging times.

Sign in / Sign up

Export Citation Format

Share Document