scholarly journals Effect of Type and Concentration of Nanoclay on the Mechanical and Physicochemical Properties of Bis-GMA/TTEGDMA Dental Resins

Polymers ◽  
2020 ◽  
Vol 12 (3) ◽  
pp. 601 ◽  
Author(s):  
J. J. Encalada-Alayola ◽  
Y. Veranes-Pantoja ◽  
J. A. Uribe-Calderón ◽  
J. V. Cauich-Rodríguez ◽  
J. M. Cervantes-Uc
Keyword(s):  
Mechanical Properties ◽  
Bending Strength ◽  
Mechanical Analysis ◽  
Resin Composites ◽  
Dental Resin ◽  
Mineral Concentration ◽  
Dental Resins ◽  
Organically Modified ◽  
Minimum Depth ◽  
Dental Restorative

Bis-GMA/TTEGDMA-based resin composites were prepared with two different types of nanoclays: an organically modified laminar clay (Cloisite® 30B, montmorillonite, MMT) and a microfibrous clay (palygorskite, PLG). Their physicochemical and mechanical properties were then determined. Both MMT and PLG nanoclays were added into monomer mixture (1:1 ratio) at different loading levels (0, 2, 4, 6, 8 and 10 wt.%), and the resulting composites were characterized by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA) and mechanical testing (bending and compressive properties). Thermal properties, depth of cure and water absorption were not greatly affected by the type of nanoclay, while the mechanical properties of dental resin composites depended on both the variety and concentration of nanoclay. In this regard, composites containing MMT displayed higher mechanical strength (both flexural and compression) than those resins prepared with PLG due to a poor nanoclay dispersion as revealed by SEM. Solubility of the composites was dependent not only on nanoclay-type but also the mineral concentration. Dental composites fulfilled the minimum depth cure and solubility criteria set by the ISO 4049 standard. In contrast, the minimum bending strength (50 MPa) established by the international standard was only satisfied by the dental resins containing MMT. Based on these results, composites containing either MMT or PLG (at low filler contents) are potentially suitable for use in dental restorative resins, although those prepared with MMT displayed better results.

scholarly journals Effect of Accelerated Aging on Some Mechanical Properties and Wear of Different Commercial Dental Resin Composites

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2769
Author(s):  
Jonne Oja ◽  
Lippo Lassila ◽  
Pekka K. Vallittu ◽  
Sufyan Garoushi
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Accelerated Aging ◽  
Wear Depth ◽  
Resin Composites ◽  
Expiration Date ◽  
Dental Resin ◽  
Hydrothermal Aging ◽  
Dental Resin Composites

The aim of current in vitro research was to determine the effect of hydrothermal accelerated aging on the mechanical properties and wear of different commercial dental resin composites (RCs). In addition, the effect of expiration date of the composite prior its use was also evaluated. Five commercially available RCs were studied: Conventional RCs (Filtek Supreme XTE, G-aenial Posterior, Denfil, and >3y expired Supreme XTE), bulk-fill RC (Filtek Bulk Fill), and short fiber-reinforced RC (everX Posterior). Three-point flexural test was used for determination of ultimate flexural strength (n = 8). A vickers indenter was used for testing surface microhardness. A wear test was conducted with 15,000 chewing cycles using a dual-axis chewing simulator. Wear pattern was analyzed by a three-dimensional (3D) noncontact optical profilometer. Degree of C=C bond conversion of monomers was determined by FTIR-spectrometry. The specimens were either dry stored for 48 h (37 °C) or boiled (100 °C) for 16 h before testing. Scanning electron microscopy (SEM) was used to evaluate the microstructure of each material. Data were analyzed using ANOVA (p = 0.05). Hydrothermal aging had no significant effects on the surface wear and microhardness of tested RCs (p > 0.05). While flexural strength significantly decreased after aging (p < 0.05), except for G-aenial Posterior, which showed no differences. The lowest average wear depth was found for Filtek Bulk Fill (29 µm) (p < 0.05), while everX Posterior and Denfil showed the highest wear depth values (40, 39 µm) in both conditions. Passing the expiration date for 40 months did not affect the flexural strength and wear of tested RC. SEM demonstrated a significant number of small pits on Denfil’s surface after aging. It was concluded that the effect of accelerated aging may have caused certain weakening of the RC of some brands, whereas no effect was found with one brand of RC. Thus, the accelerated aging appeared to be more dependent on material and tested material property.

Evaluating antibacterial and surface mechanical properties of chitosan modified dental resin composites

2020 ◽  
Vol 28 (2) ◽  
pp. 165-173 ◽  
Author(s):  
Shahid Ali ◽  
Laila Sangi ◽  
Naresh Kumar ◽  
Bharat Kumar ◽  
Zohaib Khurshid ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Resin Composites ◽  
Dental Resin ◽  
Dental Resin Composites

Characterization of Nano- and Micro-Filled Resin Composites Used as Dental Restorative Materials

2008 ◽  
Author(s):  
Dalia Abdel Hamid ◽  
Amal Esawi ◽  
Inas Sami ◽  
Randa Elsalawy
Keyword(s):  
Resin Composite ◽  
Physical And Mechanical Properties ◽  
Sem Analysis ◽  
Indentation Modulus ◽  
Resin Composites ◽  
Adhesively Bonded ◽  
Dental Resin ◽  
Tooth Structure ◽  
Dental Restorative

Adhesively-bonded resin composites have the advantage of conserving sound tooth structure with the potential for tooth reinforcement, while at the same time providing an aesthetically acceptable restoration. However, no composite material has been able to meet both the functional needs of posterior restorations and the superior aesthetics required for anterior restoration. In an attempt to develop a dental resin composite that had the mechanical strength of hybrid composite materials and the superior polish and gloss retention associated with microfilled materials, nanofilled resin composites have been introduced in the market. Although nanofillers are the most popular fillers utilized in current visible light-activated dental resin composites and are claimed to be the solution for the most challenging material limitations as a universal restorative material, the mechanisms by which these fillers influence the resin composite properties are not well explained. In this study, some physical and mechanical properties of a nanofilled resin composite containing 60 vol. % zirconia and silica fillers were evaluated and compared to those of a microhybrid resin composite of the same composition. The nanofilled resin composite was found to have equivalent polymerization shrinkage and depth of cure to the microhybrid material but a slightly lower degree of conversion and density. Regarding mechanical behaviour, although the nanocomposite was found to exhibit significantly higher wear resistance, and equivalent flexural strength, its indentation modulus and nanohardness were slightly lower. Field-emission scanning electron microscopy (FE-SEM) analysis was conducted in order to evaluate the microstructure and to obtain a better understanding of the effect of the nanofillers on the behaviour of the nanocomposite.

Ca-Doped mesoporous SiO2/dental resin composites with enhanced mechanical properties, bioactivity and antibacterial properties

2018 ◽  
Vol 6 (3) ◽  
pp. 477-486 ◽  
Author(s):  
Yu Zhang ◽  
Cui Huang ◽  
Jiang Chang
Keyword(s):  
Mechanical Properties ◽  
Antibacterial Activity ◽  
Antibacterial Properties ◽  
Resin Composites ◽  
Dental Resin ◽  
Dental Resin Composites ◽  
Mesoporous Sio2

MCS containing resin composites possess enhanced mechanical properties and antibacterial activity, and can smartly induce the deposition of apatite minerals.

Developing a novel antibacterial dental resin composite with improved properties

2019 ◽  
Vol 53 (22) ◽  
pp. 3085-3092 ◽  
Author(s):  
Xin Wen ◽  
Rashed Almousa ◽  
Gregory G Anderson ◽  
Dong Xie
Keyword(s):  
Compressive Strength ◽  
Antibacterial Activity ◽  
Resin Composite ◽  
Resin Composites ◽  
Dental Resin ◽  
Bacterial Viability ◽  
Mechanical And Physical Properties ◽  
Mechanical Strengths ◽  
Dental Restorative ◽  
Modified Resin

A novel antibacterial resin composite has been developed and evaluated. Glycerol dimethacrylate was derivatized to have an antibacterial moiety attached and incorporated to a conventional resin composite formulation. Compressive strength and bacterial viability were used to evaluate the modified resin composites. Results showed that the modified resin composites showed a significantly enhanced antibacterial activity along with improved mechanical and physical properties. It was found that bromine-containing resin composite showed a higher antibacterial activity than its chlorine-containing counterpart. The modified resin composites showed an increase of 37–41% in yield strength, 23–27% in modulus, 9–15% in diametral tensile strength and 5–12% in flexural strength and a decrease of 35–69% in bacterial viability, 20–37% in water sorption, 7–12% in shrinkage and 7–10% in compressive strength, as compared to unmodified resin composite. Within the limitations of this study, the modified resin composite may potentially be developed into a clinically useful dental restorative since it demonstrated good mechanical strengths and potent antibacterial function.

A Study on Mechanical Behavior of Dental Hard Tissues and Dental Restorative Materials by Three-Point Bending Test

2014 ◽  
Author(s):  
K. J. Chun ◽  
C. Y. Kim ◽  
J. Y. Lee
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloy ◽  
Gold Alloy ◽  
Bending Test ◽  
Dental Resin ◽  
Three Point Bending ◽  
Bending Force ◽  
Dental Restorative Materials ◽  
Restorative Materials ◽  
Dental Restorative

Dental restorative materials including amalgam, dental ceramic, gold alloy, dental resin, zirconia, and titanium alloy are used to reconstruct damaged teeth, as well as to recover their function. In this study, the mechanical properties of various dental restorative materials were determined using test specimens of identical shape and dimension under the same three-point bending test condition, and the test results were compared to enamel and dentin. The maximum bending force of enamel and dentin was 6.9 ± 2.1 N and 39.7 ± 8.3 N, and the maximum bending deflection was 0.12 ± 0.02 mm and 0.25 ± 0.03 mm, respectively. The maximum bending force of amalgam, dental ceramic, gold alloy, dental resin, zirconia, and titanium alloy were 1.9 ± 0.4 N, 2.7 ± 0.6 N, 66.9 ± 4.1 N, 2.7 ± 0.3 N, 19.0 ± 2.0 N, and 121.3 ± 6.8 N, respectively, and the maximum bending deflection was 0.20 ± 0.08 mm, 0.28 ± 0.07 mm, 2.53 ± 0.12 mm, 0.37 ± 0.05 mm, 0.39 ± 0.05 m, and 2.80 ± 0.08 mm, respectively. The dental restorative materials that possessed greater maximum bending force than that of enamel were gold alloy, zirconia, and titanium alloy. Gold alloy and titanium alloy had greater maximum bending force than dentin. The dental restorative materials that possessed greater maximum bending deflection than that of enamel were all of the dental restorative materials, and the dental restorative materials that possessed greater maximum bending deflection than that of dentin were all of the dental restorative materials except amalgam. The appropriate dental restorative materials for enamel are gold alloy and zirconia and for dentin is gold alloy concerning the maximum bending force and the maximum bending deflection. These results are expected to aid dentists in their choice of better clinical treatment and to contribute to the development of dental restorative materials that possess properties that are most similar to the mechanical properties of dental hard tissue.

scholarly journals Development of Chlorhexidine Loaded Halloysite Nanotube Based Experimental Resin Composite with Enhanced Physico-Mechanical and Biological Properties for Dental Applications

2020 ◽  
Vol 4 (2) ◽  
pp. 81 ◽  
Author(s):  
Tejas Barot ◽  
Deepak Rawtani ◽  
Pratik Kulkarni
Keyword(s):  
Mechanical Properties ◽  
Resin Composite ◽  
Biological Properties ◽  
Degree Of Conversion ◽  
Dental Composites ◽  
Resin Composites ◽  
Dental Resin ◽  
Dental Resin Composites ◽  
Mass Fractions ◽  
Nih 3T3

Objective: The objective of this study was to explore the effect of Chlorhexidine-loaded Halloysite nanotubes (HNT/CHX) fillers (diverse mass fractions from 1 to 10 wt.%) on physicochemical, morphological and biological properties of newly developed experimental dental resin composite, in order to compare with the properties of composites composed of conventional glass fillers. Methods: The dental resin composites were prepared by incorporating various proportions of HNT/CHX. Six different groups of specimens: control group and five groups composed of varied mass fractions of HNT/CHX (e.g., 1.0, 2.5, 5.0, 7.5 and 10 wt.%) as fillers in each group were fabricated. Mechanical properties of the composites were monitored, using UTM. The degree of conversion of dental resin composites and their depth of cure were also evaluated. Antimicrobial properties of dental composites were studied in vitro by applying agar diffusion test on strain Streptococcus mutans and cytotoxicity were studied using NIH-3T3 cell line. Results: The incorporation of varied mass fractions (1.0 to 5.0 wt.%) of HNT/CHX in dental resins composites enhanced mechanical properties considerably with significant antibacterial activity. The slight decrease in curing depth and degree of conversion values of composites indicates its durability. No cytotoxicity was noticed on NIH-3T3 cell lines. Significance: Consistent distribution of HNT/CHX as a filler into dental composites could substantially improve not only mechanical properties but also biological properties of dental composites.

scholarly journals Evaluation of the Degree of Conversion, Residual Monomers and Mechanical Properties of Some Light-Cured Dental Resin Composites

Materials ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2109 ◽  
Author(s):  
Marioara Moldovan ◽  
Robert Balazsi ◽  
Andrada Soanca ◽  
Alexandra Roman ◽  
Codruta Sarosi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Chemical Properties ◽  
Degree Of Conversion ◽  
Resin Composites ◽  
Mechanical Parameters ◽  
Dental Resin ◽  
Posterior Teeth ◽  
Commercial Resin ◽  
Diametral Tensile Strength

The novelty of this study consists in the formulation and characterization of three experimental dental composites (PM, P14M, P2S) for cervical dental lesion restoration compared to the commercial composites Enamel plus HRi® - En (Micerium S.p.A, Avengo, Ge, Italy), G-ænial Anterior® - Ge, (GC Europe N.V., Leuven, Belgium), Charisma® - Ch (Heraeus Kulzer, Berkshire, UK). The physio-chemical properties were studied, like the degree of conversion and the residual monomers in cured samples using FTIR-ATR (attenuated total reflectance) and HPLC-UV (ultraviolet detection), as well as the evaluation of the mechanical properties of the materials. The null hypothesis was that there would be no differences between experimental and commercial resin composites regarding the evaluated parameters. Statistical analysis revealed that water and saliva storage induced significant modifications of all mechanical parameters after three months for all tested materials, except for a few comparisons for each type of material. Storage medium seemed not to alter the values of mechanical parameters in comparison with the initial ones for: diametral tensile strength (DTS-saliva for Ge and PM, compressive strength (CS)-water for Ch, DTS-water and Young’s modulus YM-saliva for P14M and YM-water/ saliva for P2S (p > 0.05). Two of the experimental materials showed less than 1% residual monomers, which sustains good polymerization efficiency. Experimental resin composites have good mechanical properties, which makes them recommendable for the successful use in load-bearing surfaces of posterior teeth.

Sign in / Sign up

Export Citation Format

Share Document