scholarly journals Electrically-Responsive Reversible Polyketone/MWCNT Network through Diels-Alder Chemistry

Polymers ◽  
2018 ◽  
Vol 10 (10) ◽  
pp. 1076 ◽  
Author(s):  
Rodrigo Araya-Hermosilla ◽  
Andrea Pucci ◽  
Patrizio Raffa ◽  
Dian Santosa ◽  
Paolo Pescarmona ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Polymer Networks ◽  
Conductive Polymer ◽  
Mechanical Analysis ◽  
Diels Alder ◽  
Resistive Heating ◽  
Compression Moulding ◽  
Electrically Conductive ◽  
The Matrix ◽  
Tan Δ

This study examines the preparation of electrically conductive polymer networks based on furan-functionalised polyketone (PK-Fu) doped with multi-walled carbon nanotubes (MWCNTs) and reversibly crosslinked with bis-maleimide (B-Ma) via Diels-Alder (DA) cycloaddition. Notably, the incorporation of 5 wt.% of MWCNTs results in an increased modulus of the material, and makes it thermally and electrically conductive. Analysis by X-ray photoelectron spectroscopy indicates that MWCNTs, due to their diene/dienophile character, covalently interact with the matrix via DA reaction, leading to effective interfacial adhesion between the components. Raman spectroscopy points to a more effective graphitic ordering of MWCNTs after reaction with PK-Fu and B-Ma. After crosslinking the obtained composite via the DA reaction, the softening point (tan(δ) in dynamic mechanical analysis measurements) increases up to 155 °C, as compared to the value of 130 °C for the PK-Fu crosslinked with B-Ma and that of 140 °C for the PK-Fu/B-Ma/MWCNT nanocomposite before resistive heating (responsible for crosslinking). After grinding the composite, compression moulding (150 °C/40 bar) activates the retro-DA process that disrupts the network, allowing it to be reshaped as a thermoplastic. A subsequent process of annealing via resistive heating demonstrates the possibility of reconnecting the decoupled DA linkages, thus providing the PK networks with the same thermal, mechanical, and electrical properties as the crosslinked pristine systems.

scholarly journals The Influence of Compounding Parameters on the Electrical Conductivity of LDPE/Cu Conductive Polymer Composites (CPCs)

2021 ◽  
Vol 2080 (1) ◽  
pp. 012008
Author(s):  
Farah Badrul ◽  
Khairul Anwar Abdul Halim ◽  
MohdArif Anuar Mohd Salleh ◽  
Azlin Fazlina Osman ◽  
Nor Asiah Muhamad ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Polymer Composites ◽  
Low Cost ◽  
Conductive Polymer ◽  
Conductive Filler ◽  
Filler Loading ◽  
Electrically Conductive ◽  
Statistical Software ◽  
Conductive Polymer Composites ◽  
The Matrix

Abstract Low-linear density (LDPE) and copper (Cu) were used as main polymer matrix and conductive filler in order to produce electrically conductive polymer composites (CPC). The selection of the matrix and conductive filler were based on their due to its excellence properties, resistance to corrosion, low cost and electrically conductive. This research works is aimed to establish the effect of compounding parameter on the electrical conductivity of LDPE/Cu composites utilising the design of experiments (DOE). The CPCs was compounded using an internal mixer where all formulations were designed by statistical software. The scanning electron micrograph (SEM) revealed that the Cu conductive filler had a flake-like shape, and the electrical conductivity was found to be increased with increasing filler loading as measured using the four-point probe technique. The conductivity data obtained were then analysed by using the statistical software to establish the relationship between the compounding parameters and electrical conductivity where it was found based that the compounding parameters have had an effect on the conductivity of the CPC.

scholarly journals The Influence of the Furan and Maleimide Stoichiometry on the Thermoreversible Diels–Alder Network Polymerization

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2522
Author(s):  
Ali Safaei ◽  
Seppe Terryn ◽  
Bram Vanderborght ◽  
Guy Van Assche ◽  
Joost Brancart
Keyword(s):  
Transition Temperature ◽  
Functional Groups ◽  
Polymer Networks ◽  
Viscoelastic Behavior ◽  
Mechanical Analysis ◽  
Thermomechanical Properties ◽  
Diels Alder ◽  
Stoichiometric Ratio ◽  
Self Healing ◽  
Scanning Calorimetry

In recent work, the thermoreversible Diels–Alder reaction between furan and maleimide functional groups has been studied extensively in the context of self-healing elastomers and thermosets. To elaborate the influence of the stoichiometric ratio between the maleimide and furan reactive groups on the thermomechanical properties and viscoelastic behavior of formed reversible covalent polymer networks, a series of Diels–Alder-based networks with different stoichiometric ratios was synthesized. Differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and dynamic rheology measurements were performed on the reversible polymer networks, to relate the reversible network structure to the material properties and reactivity. Such knowledge allows the design and optimization of the thermomechanical behavior of the reversible networks for intended applications. Lowering the maleimide-to-furan ratio creates a deficit of maleimide functional groups, resulting in a decrease in the crosslink density of the system, and a consequent decrease in the glass transition temperature, Young’s modulus, and gel transition temperature. The excess of unreacted furan in the system results in faster reaction and healing kinetics and a shift of the reaction equilibrium.

scholarly journals Self-Healing in Mobility-Restricted Conditions Maintaining Mechanical Robustness: Furan–Maleimide Diels–Alder Cycloadditions in Polymer Networks for Ambient Applications

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2543 ◽  
Author(s):  
Dorothee Ehrhardt ◽  
Jessica Mangialetto ◽  
Jolien Bertouille ◽  
Kurt Van Durme ◽  
Bruno Van Mele ◽  
...  
Keyword(s):  
Structural Integrity ◽  
Network Formation ◽  
Polymer Networks ◽  
Mechanical Analysis ◽  
Diels Alder ◽  
Self Healing ◽  
Ambient Conditions ◽  
Scanning Calorimetry ◽  
Diffusion Controlled ◽  
Cure Temperature

Two reversible polymer networks, based on Diels–Alder cycloadditions, are selected to discuss the opportunities of mobility-controlled self-healing in ambient conditions for which information is lacking in literature. The main methods for this study are (modulated temperature) differential scanning calorimetry, microcalorimetry, dynamic rheometry, dynamic mechanical analysis, and kinetic simulations. The reversible network 3M-3F630 is chosen to study the conceptual aspects of diffusion-controlled Diels–Alder reactions from 20 to 65 °C. Network formation by gelation is proven and above 30 °C gelled glasses are formed, while cure below 30 °C gives ungelled glasses. The slow progress of Diels–Alder reactions in mobility-restricted conditions is proven by the further increase of the system’s glass transition temperature by 24 °C beyond the cure temperature of 20 °C. These findings are employed in the reversible network 3M-F375PMA, which is UV-polymerized, starting from a Diels–Alder methacrylate pre-polymer. Self-healing of microcracks in diffusion-controlled conditions is demonstrated at 20 °C. De-gelation measurements show the structural integrity of both networks up to at least 150 °C. Moreover, mechanical robustness in 3M-F375PMA is maintained by the poly(methacrylate) chains to at least 120 °C. The self-healing capacity is simulated in an ambient temperature window between −40 and 85 °C, supporting its applicability as self-healing encapsulant in photovoltaics.

Dynamic Mechanical Analysis of Polyurethane-Epoxy Interpenetrating Polymer Networks

2009 ◽  
Vol 21 (5) ◽  
pp. 608-623 ◽  
Author(s):  
Mariana Cristea ◽  
Sorin Ibanescu ◽  
Constantin N. Cascaval ◽  
Dan Rosu
Keyword(s):  
Activation Energy ◽  
Molecular Dynamics ◽  
Dynamic Mechanical Analysis ◽  
Loss Factor ◽  
Loss Modulus ◽  
Polymer Networks ◽  
Mechanical Analysis ◽  
Interpenetrating Polymer Networks ◽  
Dynamic Mechanical ◽  
Tan Δ

A series of semi-interpenetrated polymer networks based on bisphenol A epoxy resin and polyurethane was synthesized by sequential procedure. The molecular dynamics of polyurethane incorporated in the resin network with increasing amounts of resin was followed by dynamic mechanical analysis. All phenomena that concur in the material are evaluated by cross-examination of the storage modulus ( E'), loss modulus ( E'') and loss factor (tan δ) variation with temperature. Complex aspects were elucidated in consecutive heating-cooling-heating cycles and by calculating the apparent activation energy of relaxations in multiplex experiments.

Polyamide 6/Polyurethane/Graphite Composites Prepared by Anionic Polymerization Process. I. Mechanical Properties

2012 ◽  
Vol 532-533 ◽  
pp. 40-44
Author(s):  
Xin Deng ◽  
Du Xin Li ◽  
Jin Wang ◽  
Jun Yang
Keyword(s):  
Mechanical Properties ◽  
Anionic Polymerization ◽  
Polyamide 6 ◽  
Mechanical Analysis ◽  
Polymerization Process ◽  
Test Results ◽  
Nucleation Effect ◽  
The Matrix ◽  
Tan Δ ◽  
Graphite Composites

Polyamide 6/polyurethane/graphite composites have been prepared by anionic polymerization process. The effect of graphite concentration on mechanical properties of the composites was investigated. The test results show that with increment of graphite content, tensile strength of the composites increases firstly, and then decreases, while notch impact strength decreases. The change of mechanical properties of the composites is attributed to the dispersion of graphite, the interfacial properties between the matrix and graphite and the nucleation effect of graphite. In addition, the relationships between loss factor(Tan δ), storage module(E’) and temperature were investigated using Dynamic Mechanical Analysis(DMTA), and the morphological characteristic of the composites were studied using Scanning Electronic Microscope (SEM).

scholarly journals Thermally Switchable Electrically Conductive Thermoset rGO/PK Self-Healing Composites

Polymers ◽  
2021 ◽  
Vol 13 (3) ◽  
pp. 339
Author(s):  
Esteban Araya-Hermosilla ◽  
Alice Giannetti ◽  
Guilherme Macedo R. Lima ◽  
Felipe Orozco ◽  
Francesco Picchioni ◽  
...  
Keyword(s):  
Smart Materials ◽  
High Performance ◽  
Polymer Network ◽  
Conductive Polymer ◽  
Alder Reaction ◽  
Diels Alder ◽  
Self Healing ◽  
Stimuli Responsive ◽  
Electrically Conductive ◽  
Suitable Material

Among smart materials, self-healing is one of the most studied properties. A self-healing polymer can repair the cracks that occurred in the structure of the material. Polyketones, which are high-performance thermoplastic polymers, are a suitable material for a self-healing mechanism: a furanic pendant moiety can be introduced into the backbone and used as a diene for a temperature reversible Diels-Alder reaction with bismaleimide. The Diels-Alder adduct is formed at around 50 °C and broken at about 120 °C, giving an intrinsic, stimuli-responsive self-healing material triggered by temperature variations. Also, reduced graphene oxide (rGO) is added to the polymer matrix (1.6–7 wt%), giving a reversible OFF-ON electrically conductive polymer network. Remarkably, the electrical conductivity is activated when reaching temperatures higher than 100 °C, thus suggesting applications as electronic switches based on self-healing soft devices.

Investigation of Polyoxometalate-(Poly)pyrrole Heterogeneous Nanostructures as Cathodes for Rechargeable Magnesium-Ion Batteries

2018 ◽  
Author(s):  
Hakeem K. Henry ◽  
Sang Bok Lee
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Active Material ◽  
Conductive Polymer ◽  
Current Collector ◽  
Constant Current ◽  
Anodized Aluminum ◽  
Transmission Electron ◽  
Pyrrole Monomer

The PMo<sub>12</sub>-PPy heterogeneous cathode was synthesized electrochemically. In doing so, the PMo<sub>12</sub> redox-active material was impregnated throughout the conductive polymer matrix of the poly(pyrrole) nanowires. All chemicals and reagents used were purchased from Sigma-Aldrich. Anodized aluminum oxide (AAO) purchased from Whatman served as the porous hard template for nanowire deposition. A thin layer of gold of approximately 200nm was sputtered onto the disordered side of the AAO membrane to serve as the current collector. Copper tape was connected to the sputtered gold for contact and the device was sealed in parafilm with heat with an exposed area of 0.32 cm<sup>2</sup> to serve as the electroactive area for deposition. All electrochemical synthesis and experiments were conducted using a Bio-Logic MPG2 potentiostat. The deposition was carried out using a 3-electrode beaker cell setup with a solution of acetonitrile containing 5mM and 14mM of the phosphomolybdic acid and pyrrole monomer, respectively. The synthesis was achieved using chronoamperometry to apply a constant voltage of 0.8V vs. Ag/AgCl (BASi) to oxidatively polymerize the pyrrole monomer to poly(pyrrole). To prevent the POM from chemically polymerizing the pyrrole, an injection method was used in which the pyrrole monomer was added to the POM solution only after the deposition voltage had already been applied. The deposition was well controlled by limiting the amount of charge transferred to 300mC. Following deposition, the AAO template was removed by soaking in 3M sodium hydroxide (NaOH) for 20 minutes and rinsed several times with water. After synthesis, all cathodes underwent electrochemical testing to determine their performance using cyclic voltammetry and constant current charge-discharge cycling in 0.1 M Mg(ClO<sub>4</sub>)<sub>2</sub>/PC electrolyte. The cathodes were further characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), scanning transmission electron microscopy (STEM), and x-ray photoelectron spectroscopy (XPS).

scholarly journals Digital logic gates in soft, conductive mechanical metamaterials

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Charles El Helou ◽  
Philip R. Buskohl ◽  
Christopher E. Tabor ◽  
Ryan L. Harne
Keyword(s):  
Integrated Circuits ◽  
Electronic Materials ◽  
Polymer Networks ◽  
Conductive Polymer ◽  
Network Connectivity ◽  
Logic Gates ◽  
Boolean Logic ◽  
Digital Logic ◽  
Mechanical Metamaterials ◽  
Logic Operations

AbstractIntegrated circuits utilize networked logic gates to compute Boolean logic operations that are the foundation of modern computation and electronics. With the emergence of flexible electronic materials and devices, an opportunity exists to formulate digital logic from compliant, conductive materials. Here, we introduce a general method of leveraging cellular, mechanical metamaterials composed of conductive polymers to realize all digital logic gates and gate assemblies. We establish a method for applying conductive polymer networks to metamaterial constituents and correlate mechanical buckling modes with network connectivity. With this foundation, each of the conventional logic gates is realized in an equivalent mechanical metamaterial, leading to soft, conductive matter that thinks about applied mechanical stress. These findings may advance the growing fields of soft robotics and smart mechanical matter, and may be leveraged across length scales and physics.

scholarly journals Improvement of the thermal stability of dendritic silver-coated copper microparticles by surface modification based on molecular self-assembly

2021 ◽  
Vol 8 (1) ◽  
Author(s):  
Tae Hyeong Kim ◽  
Hyeji Kim ◽  
Hyo Jun Jang ◽  
Nara Lee ◽  
Kwang Hyun Nam ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Photoelectron Spectroscopy ◽  
Self Assembly ◽  
Electrically Conductive ◽  
X Ray ◽  
Alkyl Chains ◽  
Conductive Film ◽  
Initial Resistance ◽  
Thermal Stability Of ◽  
Scanning Electron

AbstractIn the study reported herein, silver-coated copper (Ag/Cu) powder was modified with alkanethiols featuring alkyl chains of different lengths, namely butyl, octyl, and dodecyl, to improve its thermal stability. The modification of the Ag/Cu powders with adsorbed alkanethiols was confirmed by scanning electron microscopy with energy dispersive spectroscopy, X-ray photoelectron spectroscopy, and thermogravimetric analysis. Each powder was combined with an epoxy resin to prepare an electrically conductive film. The results confirmed that the thermal stability of the films containing alkanethiol-modified Ag/Cu powders is superior to that of the film containing untreated Ag/Cu powder. The longer the alkyl group in the alkanethiol-modified Ag/Cu powder, the higher the initial resistance of the corresponding electrically conductive film and the lower the increase in resistance induced by heat treatment.

Sign in / Sign up

Export Citation Format

Share Document