scholarly journals Reinforcement of Thermoplastic Corn Starch with Crosslinked Starch/Chitosan Microparticles

Polymers ◽  
2018 ◽  
Vol 10 (9) ◽  
pp. 985 ◽  
Author(s):  
Diana Paiva ◽  
André Pereira ◽  
Ana Pires ◽  
Jorge Martins ◽  
Luísa Carvalho ◽  
...  
Keyword(s):  
Water Solubility ◽  
Corn Starch ◽  
Polymer Network ◽  
Xrd Analysis ◽  
Thermoplastic Starch ◽  
Interpenetrating Polymer Network ◽  
Melt Mixing ◽  
Chitosan Microparticles ◽  
Polysaccharide Composition ◽  
Low Solubility

Microparticles of corn starch and chitosan crosslinked with glutaraldehyde, produced by the solvent exchange technique, are studied as reinforcement fillers for thermoplastic corn starch plasticized with glycerol. The presence of 10% w/w chitosan in the microparticles is shown to be essential to guaranteeing effective crosslinking, as demonstrated by water solubility assays. Crosslinked chitosan forms an interpenetrating polymer network with starch chains, producing microparticles with a very low solubility. The thermal stability of the microparticles is in agreement with their polysaccharide composition. An XRD analysis showed that they have crystalline fraction of 32% with Va-type structure, and have no tendency to undergo retrogradation. The tensile strength, Young’s modulus, and toughness of thermoplastic starch increased by the incorporation of the crosslinked starch/chitosan microparticles by melt-mixing. Toughness increased 360% in relation to unfilled thermoplastic starch.

scholarly journals Preparation and characterization of corn starch/PVA/glycerol composite films incorporated with ε-polylysine as a novel antimicrobial packaging material

e-Polymers ◽  
2020 ◽  
Vol 20 (1) ◽  
pp. 154-161 ◽  
Author(s):  
Gao Yurong ◽  
Li Dapeng
Keyword(s):  
Water Solubility ◽  
Corn Starch ◽  
Composite Films ◽  
Antimicrobial Properties ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
Packaging Material ◽  
Hydroxyl Group ◽  
Electron Microscopic ◽  
Antimicrobial Packaging

AbstractCorn starch/polyvinyl alcohol (PVA)/glycerol composite films incorporated with ε-polylysine were prepared, and their properties were investigated. The Fourier-transform infrared (FTIR) spectroscopy indicated that the interactions happened between the amino group of ε-polylysine and hydroxyl group starch/PVA composite films. X-ray diffraction (XRD) analysis showed that the addition of ε-polylysine decreased the intensity of all crystal peaks. Thermogravimetric (TGA) analysis suggested that ε-polylysine improved the thermal stability of composite films. Scanning electron microscopic (SEM) analysis showed that the upper surface of composite films incorporated with ε-polylysine presented more compact and flat surface. The antimicrobial activity of the composite film progressively increased with the increasing of ε-polylysine concentration (P < 0.05). The tensile strength, elongation at break and water absorption significantly increased, whereas water solubility decreased with the increasing of ε-polylysine concentration (P < 0.05). Therefore, the corn starch/PVA/glycerol composite films incorporated with ε-polylysine had good mechanical, physical and antimicrobial properties and could have potential application as a novel antimicrobial packaging material.

scholarly journals Flexible Thermoplastic Starch Films Functionalized With Copper Particles for Packaging of Food Products

2020 ◽  
Author(s):  
Olivia López ◽  
María E. Villanueva ◽  
Guillermo J. Copello ◽  
Marcelo A Villar
Keyword(s):  
Inhibitory Concentration ◽  
Corn Starch ◽  
Composite Films ◽  
Thermoplastic Starch ◽  
Biodegradable Films ◽  
Melt Mixing ◽  
Elongation At Break ◽  
Copper Particles ◽  
Starch Films ◽  
Fresh Products

Abstract Biodegradable films based on thermoplastic corn starch (TPS) and copper particles with antimicrobial capacity were developed. Copper nanoparticles (Cu) and silica coated copper microparticles (Si-Cu) in the range of 0.25 to 5 % were used. Composite films were obtained by melt-mixing and subsequent thermo-compression. Particles distribution within TPS matrix and the presence of some pores and cracks, induced by Si-Cu particles, was evaluated by SEM. The presence of both fillers gave to composite films a brown pigmentation and decreased their transparency; these effects were more pronounced at higher particles concentrations. Regarding mechanical properties, copper particles at 1 and 5 % acted as reinforcing agents increasing the maximum tensile strength but their presence lead to a decrease in elongation at break, affecting films ductility. Composites inhibited the growth of Gram+ and Gram- bacteria, demonstrating their antimicrobial capacity. Copper effectively migrated to a simulant of aqueous foods and naked particles concentration in the simulant medium resulted higher than the minimum inhibitory concentration for bacteria. The characteristics and properties of developed composite films make them an interesting material for food primary packaging, mainly for meat fresh products.

scholarly journals Flexible Thermoplastic Starch Films Functionalized With Copper Particles for Packaging of Food Products

2020 ◽  
Author(s):  
Olivia López ◽  
María E. Villanueva ◽  
Guillermo J. Copello ◽  
Marcelo A Villar
Keyword(s):  
Inhibitory Concentration ◽  
Corn Starch ◽  
Composite Films ◽  
Thermoplastic Starch ◽  
Biodegradable Films ◽  
Melt Mixing ◽  
Elongation At Break ◽  
Copper Particles ◽  
Starch Films ◽  
Fresh Products

Abstract Biodegradable films based on thermoplastic corn starch (TPS) and copper particles with antimicrobial capacity were developed. Copper nanoparticles (Cu) and silica coated copper microparticles (Si-Cu) in the range of 0.25 to 5 % were used. Composite films were obtained by melt-mixing and subsequent thermo-compression. Particles distribution within TPS matrix and the presence of some pores and cracks, induced by Si-Cu particles, was evaluated by SEM. The presence of both fillers gave to composite films a brown pigmentation and decreased their transparency; these effects were more pronounced at higher particles concentrations. Regarding mechanical properties, copper particles at 1 and 5 % acted as reinforcing agents increasing the maximum tensile strength but their presence lead to a decrease in elongation at break, affecting films ductility. Composites inhibited the growth of Gram+ and Gram- bacteria, demonstrating their antimicrobial capacity. Copper effectively migrated to a simulant of aqueous foods and naked particles concentration in the simulant medium resulted higher than the minimum inhibitory concentration for bacteria.The characteristics and properties of developed composite films make them an interesting material for food primary packaging, mainly for meat fresh products.

scholarly journals Flexible Thermoplastic Starch Films Functionalized With Copper Particles for Packaging of Food Products

2020 ◽  
Author(s):  
Olivia López ◽  
María E. Villanueva ◽  
Guillermo J. Copello ◽  
Marcelo A Villar
Keyword(s):  
Inhibitory Concentration ◽  
Corn Starch ◽  
Composite Films ◽  
Thermoplastic Starch ◽  
Biodegradable Films ◽  
Melt Mixing ◽  
Elongation At Break ◽  
Copper Particles ◽  
Starch Films ◽  
Fresh Products

Abstract Biodegradable films based on thermoplastic corn starch (TPS) and copper particles with antimicrobial capacity were developed. Copper nanoparticles (Cu) and silica coated copper microparticles (Si-Cu) in the range of 0.25 to 5 % were used. Composite films were obtained by melt-mixing and subsequent thermo-compression. Particles distribution within TPS matrix and the presence of some pores and cracks, induced by Si-Cu particles, was evaluated by SEM. The presence of both fillers gave composite films a brown pigmentation and decreased their transparency; these effects were more pronounced at higher particles concentrations. Regarding mechanical properties, copper particles at 1 and 5 % acted as reinforcing agents increasing the maximum tensile strength but their presence lead to a decrease in elongation at break, affecting films ductility. Composites inhibited the growth of Gram+ and Gram- bacteria, demonstrating their antimicrobial capacity. Copper effectively migrated to a simulant of aqueous foods and naked particles concentration in the simulant medium resulted higher than the minimum inhibitory concentration for bacteria. The characteristics and properties of developed composite films make them an interesting material for food primary packaging, mainly for meat fresh products.

scholarly journals Valorization of Rice Straw into Cellulose Microfibers for the Reinforcement of Thermoplastic Corn Starch Films

2021 ◽  
Vol 11 (18) ◽  
pp. 8433
Author(s):  
Pedro A. V. Freitas ◽  
Carla I. La Fuente Arias ◽  
Sergio Torres-Giner ◽  
Chelo González-Martínez ◽  
Amparo Chiralt
Keyword(s):  
Rice Straw ◽  
Corn Starch ◽  
Composite Films ◽  
Thermoplastic Starch ◽  
Starch Granules ◽  
Melt Mixing ◽  
Cellulose Microfibers ◽  
Gelatinized Starch ◽  
Dry Heating ◽  
Starch Films

In the present study, agro-food waste derived rice straw (RS) was valorized into cellulose microfibers (CMFs) using a green process of combined ultrasound and heating treatments and were thereafter used to improve the physical properties of thermoplastic starch films (TPS). Mechanical defibrillation of the fibers gave rise to CMFs with cumulative frequencies of length and diameters below 200 and 5–15 µm, respectively. The resultant CMFs were successfully incorporated at, 1, 3, and 5 wt% into TPS by melt mixing and also starch was subjected to dry heating (DH) modification to yield TPS modified by dry heating (TPSDH). The resultant materials were finally shaped into films by thermo-compression and characterized. It was observed that both DH modification and fiber incorporation at 3 and 5 wt% loadings interfered with the starch gelatinization, leading to non-gelatinized starch granules in the biopolymer matrix. Thermo-compressed films prepared with both types of starches and reinforced with 3 wt% CMFs were more rigid (percentage increases of ~215% for TPS and ~207% for the TPSDH), more resistant to break (~100% for TPS and ~60% for TPSDH), but also less extensible (~53% for TPS and ~78% for TPSDH). The incorporation of CMFs into the TPS matrix at the highest contents also promoted a decrease in water vapor (~15%) and oxygen permeabilities (~30%). Finally, all the TPS composite films showed low changes in terms of optical properties and equilibrium moisture, being less soluble in water than the TPSDH films.

scholarly journals Porous scaffolds with the structure of an interpenetrating polymer network made by gelatin methacrylated nanoparticle-stabilized high internal phase emulsion polymerization targeted for tissue engineering

RSC Advances ◽  
2021 ◽  
Vol 11 (37) ◽  
pp. 22544-22555
Author(s):  
Atefeh Safaei-Yaraziz ◽  
Shiva Akbari-Birgani ◽  
Nasser Nikfarjam
Keyword(s):  
Tissue Engineering ◽  
Extracellular Matrix ◽  
Cell Growth ◽  
Polymer Network ◽  
Synthetic Polymers ◽  
Tissue Scaffolds ◽  
Interpenetrating Polymer Network ◽  
Porous Scaffolds ◽  
Promising Strategy ◽  
Internal Phase

The interlacing of biopolymers and synthetic polymers is a promising strategy to fabricate hydrogel-based tissue scaffolds to biomimic a natural extracellular matrix for cell growth.

scholarly journals Study of the Preparation and Properties of TPS/PBSA/PLA Biodegradable Composites

2021 ◽  
Vol 5 (2) ◽  
pp. 48
Author(s):  
Yuxuan Wang ◽  
Yuke Zhong ◽  
Qifeng Shi ◽  
Sen Guo
Keyword(s):  
Mechanical Properties ◽  
Heat Resistance ◽  
Thermoplastic Starch ◽  
Sem Analysis ◽  
Infrared Spectrometry ◽  
Fourier Transform Infrared Spectrometry ◽  
Melt Mixing ◽  
Two Phase ◽  
Biodegradable Composites ◽  
Phase Compatibility

Thermoplastic starch/butyl glycol ester copolymer/polylactic acid (TPS/PBSA/PLA) biodegradable composites were prepared by melt-mixing. The structure, microstructure, mechanical properties and heat resistance of the TPS/PBSA/PLA composites were studied by Fourier-transform infrared spectrometry (FTIR), scanning electron microscopy (SEM), tensile test and thermogravimetry tests, respectively. The results showed that PBSA or PLA could bind to TPS by hydrogen bonding. SEM analysis showed that the composite represents an excellent dispersion and satisfied two-phase compatibility when the PLA, TPS and PBSA blended by a mass ration of 10, 30, and 60. The mechanical properties and the heat resistance of TPS/PBSA/PLA composite were improved by adding PLA with content less than 10%, according to the testing results.

Sign in / Sign up

Export Citation Format

Share Document