scholarly journals Asymmetric Carrier Divider with an Irregular RF Phase on DD-MZ Modulator for Eliminating Dispersion Power Fading in RoF Communication

Photonics ◽  
2020 ◽  
Vol 7 (4) ◽  
pp. 106
Author(s):  
Gunawan Wibisono ◽  
Febrizal Ujang ◽  
Teguh Firmansyah ◽  
Purnomo S. Priambodo
Keyword(s):  
High Efficiency ◽  
Modulation Scheme ◽  
Direct Signal ◽  
Model And Simulation ◽  
Deviation Factor ◽  
Optical Single Sideband ◽  
Bias Point ◽  
Rf Signal ◽  
The Impact ◽  
The Mathematical Model

The main problem of intensity modulation (IM) in radio-over-fiber (RoF) communication is dispersion power fading (DPF), which occurs when the signal is transmitted through a dispersive link that causes a sideband cancelation effect. The DPF level of the RoF link is determined by the deviation factor (DF). The optical single-sideband (OSSB) modulation scheme, which is generated by driving one of the dual-drive Mach–Zehnder modulators (DD-MZMs), is usually used to overcome DPF. The DF value of OSSB modulation at modulation index m = 0.1 increases from 0.008 to 0.930 at m = 1. It can be said that this method is only effective at reducing DF at low m. However, as well-known information of the DD-MZM system, high-efficiency optic–electric conversions can be obtained at high m values, but DF will increase. Therefore, reducing the DPF value for high m ≥ 0.1 is interesting. It is known that in wireless communication, to reduce the impact of fading, direct signals are amplified and signals with irregular phases are used. Moreover, this paper proposes the DD-MZM with an asymmetric carrier divider as a direct signal and combines it with an irregular radio frequency (RF) phase to reduce the DPF at high m. The carrier that is generated by laser diode (LD) power (PIN) is divided asymmetrically as power modulation (PDD-MZM) and carrier arm (CA) power (PCA). Furthermore, the minimum DF is obtained when the PIN is separated as 75% for PCA and 25% for PDD-MZM with an irregular RF signal of θ = 48° and a bias point value of γ = ¾. As a result, with the same power as OSSB, this proposed structure produces DF at m = 0.1 and m = 1 with values of 0.008 and 0.03, or it can reduce DF of 96.7% at m = 1. The mathematical model and simulation model have very good agreement, which validates the proposed method.

Research on the Counterweight in the Process of Diamond Wire Saw Cutting Polysilicon

2011 ◽  
Vol 418-420 ◽  
pp. 1048-1055
Author(s):  
Liao Yuan Zhang ◽  
Jian Guang Wang ◽  
Yong Yang ◽  
Chao Wang
Keyword(s):  
High Efficiency ◽  
Processing Efficiency ◽  
Diamond Wire ◽  
Cutting Machine ◽  
Wire Saw ◽  
Diamond Wire Saw ◽  
Hard And Brittle Materials ◽  
The Impact ◽  
The Mathematical Model ◽  
Trajectory Equation

In the process of cutting hard and brittle materials , electroplated diamond wire saw cutting has been growing concern for its high-quality, high efficiency, environmental protection and other advantages. In this paper, the wire saw cutting trajectory equation and the mathematical model of counterweight were established and the variation law of counterweight was analyzed. In addition, the impact of counterweight on the processing efficiency, surface quality was studied on the USDW-1 type ultrasound diamond wire saw cutting machine by way of cutting polysilicon material.

scholarly journals Irregular Shifting of RF Driving Signal Phase to Overcome Dispersion Power Fading

Photonics ◽  
2019 ◽  
Vol 6 (4) ◽  
pp. 104 ◽  
Author(s):  
Febrizal Ujang ◽  
Teguh Firmansyah ◽  
Purnomo S. Priambodo ◽  
Gunawan Wibisono
Keyword(s):  
Chromatic Dispersion ◽  
Modulation Scheme ◽  
Rf Power ◽  
Signal Phase ◽  
Optical Wavelength ◽  
Optical Single Sideband ◽  
Mach Zehnder Modulator ◽  
Bias Point ◽  
Driving Signal ◽  
Better Than

The main problem with the radio-over-fiber (RoF) link is the decrease in the recovered radio frequency (RF) power due to the chromatic dispersion of the fiber known as dispersion power fading. One of the methods for dealing with dispersion power fading is to use the optical single sideband (OSSB) modulation scheme. The OSSB modulation scheme can be generated by biasing the dual-drive Mach–Zehnder modulator (DD-MZM) to the quadrature bias point (QBP) and shifting the RF drive signal phase (θ) by 90°, which is called the regular θ. However, the OSSB modulation scheme only overcomes dispersion power fading well at the modulation index (m) < 0.2. This paper proposes an irregular θ method to overcome dispersion power fading at all m. There are two irregular θ for every m used. The irregular θ managed to handle dispersion power fading better than OSSB modulation scheme did at every m. Specifically, the irregular θ could handle the dispersion power fading well at m ≤ 1. In sum, the irregular θ could overcome the dispersion power fading at any RF frequency and optical wavelength without having to re-adjust the transmitter.

Piezoelectric β-polymorph formation of new textiles by surface modification with coating process based on interfacial interaction on the conformational variation of poly (vinylidene fluoride) (PVDF) chains

2020 ◽  
Vol 91 (3) ◽  
pp. 31301
Author(s):  
Nabil Chakhchaoui ◽  
Rida Farhan ◽  
Meriem Boutaldat ◽  
Marwane Rouway ◽  
Adil Eddiai ◽  
...  
Keyword(s):  
High Efficiency ◽  
Vinylidene Fluoride ◽  
Research Work ◽  
Research Area ◽  
Interfacial Interaction ◽  
Tetraethyl Orthosilicate ◽  
Poly Vinylidene Fluoride ◽  
Carbon Nanofillers ◽  
The Impact ◽  
Advanced Applications

Novel textiles have received a lot of attention from researchers in the last decade due to some of their unique features. The introduction of intelligent materials into textile structures offers an opportunity to develop multifunctional textiles, such as sensing, reacting, conducting electricity and performing energy conversion operations. In this research work nanocomposite-based highly piezoelectric and electroactive β-phase new textile has been developed using the pad-dry-cure method. The deposition of poly (vinylidene fluoride) (PVDF) − carbon nanofillers (CNF) − tetraethyl orthosilicate (TEOS), Si(OCH2CH3)4 was acquired on a treated textile substrate using coating technique followed by evaporation to transform the passive (non-functional) textile into a dynamic textile with an enhanced piezoelectric β-phase. The aim of the study is the investigation of the impact the coating of textile via piezoelectric nanocomposites based PVDF-CNF (by optimizing piezoelectric crystalline phase). The chemical composition of CT/PVDF-CNC-TEOS textile was detected by qualitative elemental analysis (SEM/EDX). The added of 0.5% of CNF during the process provides material textiles with a piezoelectric β-phase of up to 50% has been measured by FTIR experiments. These results indicated that CNF has high efficiency in transforming the phase α introduced in the unloaded PVDF, to the β-phase in the case of nanocomposites. Consequently, this fabricated new textile exhibits glorious piezoelectric β-phase even with relatively low coating content of PVDF-CNF-TEOS. The study demonstrates that the pad-dry-cure method can potentially be used for the development of piezoelectric nanocomposite-coated wearable new textiles for sensors and energy harvesting applications. We believe that our study may inspire the research area for future advanced applications.

scholarly journals Theoretical Studies of the Interaction between Screw Surface and Material in the Mixer

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 962
Author(s):  
Andrzej Marczuk ◽  
Vasily Sysuev ◽  
Alexey Aleshkin ◽  
Petr Savinykh ◽  
Nikolay Turubanov ◽  
...  
Keyword(s):  
Friction Coefficient ◽  
High Efficiency ◽  
Animal Feed ◽  
Structural Features ◽  
Power Demand ◽  
Friction Coefficients ◽  
Length Unit ◽  
Mixing Chamber ◽  
Size Of Particles ◽  
The Impact

Mixing is one of the most commonly used processes in food, animal feed, chemical, cosmetic, etc., industries. It is supposed to provide high-quality homogenous, nutritious mixtures. To provide appropriate mixing of materials while maintaining the process high efficiency and low energy consumption it is crucial to explore and describe the material flow caused by the movement of mixing elements and the contact between particles. The process of mixing is also affected by structural features of the machine components and the mixing chamber, speed of mixing, and properties of the mixed materials, such as the size of particles, moisture, friction coefficients. Thus, modeling of the phenomena that accompany the process of mixing using the above-listed parameters is indispensable for appropriate implementation of the process. The paper provides theoretical power calculations that take into account the material speed change, the impact of the material friction coefficient on the screw steel surface and the impact of the friction coefficient on the material, taking into account the loading height of the mixing chamber and the chamber loading value. Dependencies between the mixer power and the product degree of fineness, rotational speed of screw friction coefficients, the number of windings per length unit, and width of the screw tape have been presented on the basis of a developed model. It has been found that power increases along with an increase in the value of these parameters. Verification of the theoretical model indicated consistence of the predicted power demand with the power demand determined in tests performed on a real object for values of the assumed, effective loading, which was 65–75%.

scholarly journals Nonlocal and Size-Dependent Dielectric Function for Plasmonic Nanoparticles

2019 ◽  
Vol 9 (15) ◽  
pp. 3083
Author(s):  
Kai-Jian Huang ◽  
Shui-Jie Qin ◽  
Zheng-Ping Zhang ◽  
Zhao Ding ◽  
Zhong-Chen Bai
Keyword(s):  
Metallic Nanoparticles ◽  
High Efficiency ◽  
Finite Size ◽  
Plasmonic Nanostructures ◽  
Accurate Analysis ◽  
Finite Size Effects ◽  
Size Dependent ◽  
Quantum Size ◽  
The Impact ◽  
Electron Energy Loss

We develop a theoretical approach to investigate the impact that nonlocal and finite-size effects have on the dielectric response of plasmonic nanostructures. Through simulations, comprehensive comparisons of the electron energy loss spectroscopy (EELS) and the optical performance are discussed for a gold spherical dimer system in terms of different dielectric models. Our study offers a paradigm of high efficiency compatible dielectric theoretical framework for accounting the metallic nanoparticles behavior combining local, nonlocal and size-dependent effects in broader energy and size ranges. The results of accurate analysis and simulation for these effects unveil the weight and the evolution of both surface and bulk plasmons vibrational mechanisms, which are important for further understanding the electrodynamics properties of structures at the nanoscale. Particularly, our method can be extended to other plasmonic nanostructures where quantum-size or strongly interacting effects are likely to play an important role.

scholarly journals The Impact of Elongation on Change in Electrical Resistance of Electrically Conductive Yarns Woven into Fabric

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3390
Author(s):  
Željko Knezić ◽  
Željko Penava ◽  
Diana Šimić Penava ◽  
Dubravko Rogale
Keyword(s):  
Mathematical Model ◽  
Electrical Resistance ◽  
Electrically Conductive ◽  
Textile Materials ◽  
Measurement Results ◽  
Conductive Yarns ◽  
Yarn Count ◽  
As Relationship ◽  
The Impact ◽  
The Mathematical Model

Electrically conductive yarns (ECYs) are gaining increasing applications in woven textile materials, especially in woven sensors suitable for incorporation into clothing. In this paper, the effect of the yarn count of ECYs woven into fabric on values of electrical resistance is analyzed. We also observe how the direction of action of elongation force, considering the position of the woven ECY, effects the change in the electrical resistance of the electrically conductive fabric. The measurements were performed on nine different samples of fabric in a plain weave, into which were woven ECYs with three different yarn counts and three different directions. Relationship curves between values of elongation forces and elongation to break, as well as relationship curves between values of electrical resistance of fabrics with ECYs and elongation, were experimentally obtained. An analytical mathematical model was also established, and analysis was conducted, which determined the models of function of connection between force and elongation, and between electrical resistance and elongation. The connection between the measurement results and the mathematical model was confirmed. The connection between the mathematical model and the experimental results enables the design of ECY properties in woven materials, especially textile force and elongation sensors.

scholarly journals Time-jerk optimal trajectory planning of hydraulic robotic excavator

2021 ◽  
Vol 13 (7) ◽  
pp. 168781402110346
Author(s):  
Yunyue Zhang ◽  
Zhiyi Sun ◽  
Qianlai Sun ◽  
Yin Wang ◽  
Xiaosong Li ◽  
...  
Keyword(s):  
Angular Velocity ◽  
Trajectory Planning ◽  
Optimal Trajectory ◽  
High Efficiency ◽  
Optimal Solution ◽  
Optimal Time ◽  
Target Point ◽  
Robotic Excavator ◽  
The Impact ◽  
Optimal Trajectory Planning

Due to the fact that intelligent algorithms such as Particle Swarm Optimization (PSO) and Differential Evolution (DE) are susceptible to local optima and the efficiency of solving an optimal solution is low when solving the optimal trajectory, this paper uses the Sequential Quadratic Programming (SQP) algorithm for the optimal trajectory planning of a hydraulic robotic excavator. To achieve high efficiency and stationarity during the operation of the hydraulic robotic excavator, the trade-off between the time and jerk is considered. Cubic splines were used to interpolate in joint space, and the optimal time-jerk trajectory was obtained using the SQP with joint angular velocity, angular acceleration, and jerk as constraints. The optimal angle curves of each joint were obtained, and the optimal time-jerk trajectory planning of the excavator was realized. Experimental results show that the SQP method under the same weight is more efficient in solving the optimal solution and the optimal excavating trajectory is smoother, and each joint can reach the target point with smaller angular velocity, and acceleration change, which avoids the impact of each joint during operation and conserves working time. Finally, the excavator autonomous operation becomes more stable and efficient.

Thermal performance comparison of different sun tracking configurations

2019 ◽  
Vol 88 (2) ◽  
pp. 20902
Author(s):  
O. Achkari ◽  
A. El Fadar
Keyword(s):  
Thermal Performance ◽  
Electricity Generation ◽  
Arid Regions ◽  
Performance Comparison ◽  
Water Desalination ◽  
Parabolic Trough ◽  
Parabolic Trough Collector ◽  
The Impact ◽  
The Mathematical Model ◽  
Good Agreement

Parabolic trough collector (PTC) is one of the most widespread solar concentration technologies and represents the biggest share of the CSP market; it is currently used in various applications, such as electricity generation, heat production for industrial processes, water desalination in arid regions and industrial cooling. The current paper provides a synopsis of the commonly used sun trackers and investigates the impact of various sun tracking modes on thermal performance of a parabolic trough collector. Two sun-tracking configurations, full automatic and semi-automatic, and a stationary one have numerically been investigated. The simulation results have shown that, under the system conditions (design, operating and weather), the PTC's performance depends strongly on the kind of sun tracking technique and on how this technique is exploited. Furthermore, the current study has proven that there are some optimal semi-automatic configurations that are more efficient than one-axis sun tracking systems. The comparison of the mathematical model used in this paper with the thermal profile of some experimental data available in the literature has shown a good agreement with a remarkably low relative error (2.93%).

scholarly journals Evaluation of an environmentally sustainable UV-assisted water treatment system for the removal of Bacillus globigii spores in water

2017 ◽  
Vol 18 (3) ◽  
pp. 968-975
Author(s):  
R. G. Silva ◽  
J. Szabo ◽  
V. Namboodiri ◽  
E. R. Krishnan ◽  
J. Rodriguez ◽  
...  
Keyword(s):  
Water Treatment ◽  
High Efficiency ◽  
Membrane Filter ◽  
Water Security ◽  
Disinfection Byproducts ◽  
Treatment System ◽  
Health Concern ◽  
Environmentally Sustainable ◽  
Inorganic Substances ◽  
The Impact

Abstract Development of greener water treatment technologies is important for the production of safe drinking water and water security applications, such as decontamination. Chlorine assisted disinfection is common and economical, but can generate disinfection byproducts (DBPs) that may be of health concern. DBPs are formed due to the reaction of chlorine with naturally occurring organic and inorganic substances in water. Currently, various innovative technologies are being developed as alternative approaches for preventing DBPs during water treatment. In this study, we evaluated the effectiveness of a novel combination of high efficiency flow filtration and UV disinfection treatment system for the removal of Bacillus globigii (B. globigii) spores in water. The filtration system consists of a charged membrane filter (CMF) that not only helps to remove suspended particles but also reduces the impact of other impurities including bio organisms. In order to get most performance details, the CMF was evaluated at clean, half-life, and end of life (EOL) conditions along with 100% UV transmittance (UVT). In addition, the effectiveness of the UV system was evaluated as a stand alone system at 100% and 70% EOL intensity. The study was conducted at the US EPA's Test and Evaluation (T&E) Facility in Cincinnati, OH, using B. globigii, a surrogate for B. anthracis spores. This non-chemical environmentally-friendly CMF/UV combination system and the stand alone UV unit showed greater than 6.0 log removal of B. globigii during the tests.

Comparison Between Two-Shaft Simple and Single-Shaft Recuperated Brayton Cycles Using Different Types of Gaseous Fuels

2010 ◽  
Author(s):  
A. K. Malkogianni ◽  
A. Tourlidakis ◽  
A. L. Polyzakis
Keyword(s):  
Natural Gas ◽  
Gas Turbines ◽  
Alternative Fuels ◽  
High Efficiency ◽  
Heating Value ◽  
Gaseous Fuels ◽  
Oil And Natural Gas ◽  
Parametric Studies ◽  
The Impact ◽  
Lower Heating

Geopolitical issues give rise to problems in the smooth and continuous flow of oil and natural gas from the production countries to the consumers’ development countries. In addition, severe environmental issues such as greenhouse gas emissions, eventually guide the consumers to fuels more suitable to the present situation. Alternative fuels such as biogas and coal gas have recently become more attractive because of their benefits, especially for electricity generation. On the other hand, the use of relatively low heating value fuels has a significant effect to the performance parameters of gas turbines. In this paper, the impact of using four fuels with different heating value in the gas turbine performance is simulated. Based on the high efficiency and commercialization criteria, two types of engines are chosen to be simulated: two-shaft simple and single-shaft recuperated cycle gas turbines. The heating values of the four gases investigated, correspond to natural gas and to a series of three gases with gradually lower heating values than that of natural gas. The main conclusions drawn from this design point (DP) and off-design (OD) analysis is that, for a given TET, efficiency increases for both engines when gases with low heating value are used. On the contrary, when power output is kept constant, the use of gases with low heating value will result in a decrease of thermal efficiency. A number of parametric studies are carried out and the effect of operating parameters on performance is assessed. The analysis is performed with customized software, which has been developed for this purpose.

Sign in / Sign up

Export Citation Format

Share Document