scholarly journals Enhanced Mechanical and Thermal Properties of Stereolithography 3D Printed Structures by the Effects of Incorporated Controllably Annealed Anatase TiO2 Nanoparticles

Nanomaterials ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 79 ◽  
Author(s):  
Suhail Mubarak ◽  
Duraisami Dhamodharan ◽  
Nidhin Divakaran ◽  
Manoj B. Kale ◽  
T. Senthil ◽  
...  
Keyword(s):  
Tio2 Nanoparticles ◽  
Photoelectron Spectroscopy ◽  
Uv Light ◽  
Anatase Phase ◽  
Low Energy ◽  
Mechanical And Thermal Properties ◽  
Tem Analysis ◽  
X Ray ◽  
Energy Bandgap ◽  
3D Printed

Fabrication of low-cost, durable and efficient metal oxide nanocomposites were successfully synthesized and reinforced with photo-resin via 3-dimensional printing. Here, we put forward a novel approach to enhance the mechanical and thermal behaviors of stereolithography (SLA) 3D printed architecture by adding TiO2 nanoparticles (TNPs) in different crystalline phases (anatase and rutile), which were obtained at different annealing temperatures from 400 °C to 1000°C. The heat-treated anatase TNPs were scrutinized by X-ray diffraction(XRD), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, diffusive reflectance spectroscopy (DRS), and transmission electron microscopy (TEM) analysis. Among all the samples, at 800 °C, annealed anatase TNPs exposed a highly crystalline anatase phase, having a low energy bandgap and a comparably high tensile strength (47.43 MPa) and high elastic modulus (2.261 GPa) for the 3D printed samples, showing improvement by 103% and 32%, respectively, compared with the printed pristine stereolithography resin (SLR) sample. Moreover, enhanced storage modulus and tan δ values were achieved via the better interfacial interactions between the incorporated nanofillers and the SLR matrix. In addition to this, enhanced thermal conductivity and thermal stability of the SLR matrix were also noted. The low energy bandgap and nanoscale size of the fillers helped to achieve good dispersion and allowed the UV light to penetrate at a maximum depth through the photo resin.

scholarly journals Grafting Hyperbranched Polymers onto TiO2 Nanoparticles via Thiol-yne Click Chemistry and Its Effect on the Mechanical, Thermal and Surface Properties of Polyurethane Coating

Materials ◽  
2019 ◽  
Vol 12 (17) ◽  
pp. 2817 ◽  
Author(s):  
Feng Zhan ◽  
Lei Xiong ◽  
Fang Liu ◽  
Chenying Li
Keyword(s):  
Click Chemistry ◽  
Tio2 Nanoparticles ◽  
Photoelectron Spectroscopy ◽  
Hyperbranched Polymers ◽  
Nanocomposite Coatings ◽  
Mechanical And Thermal Properties ◽  
Nanoparticle Dispersion ◽  
X Ray Diffraction ◽  
X Ray ◽  
Surface Modified

In this study, we proposed a novel and facile method to modify the surface of TiO2 nanoparticles and investigated the influence of the surface-modified TiO2 nanoparticles as an additive in a polyurethane (PU) coating. The hyperbranched polymers (HBP) were grafted on the surface of TiO2 nanoparticles via the thiol-yne click chemistry to reduce the aggregation of nanoparticles and increase the interaction between TiO2 and polymer matrices. The grafting of HBP on the TiO2 nanoparticles surface was investigated by means of X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), Fourier transform infrared (FT-IR), nuclear magnetic resonance (NMR) and thermogravimetry analysis (TGA). The thermal and mechanical properties of nanocomposite coatings containing various amounts of TiO2 nanoparticles were measured by dynamic mechanical thermal (DMTA) and tensile strength measurement. Moreover, the surface structure and properties of the newly prepared nanocomposite coatings were examined. The experimental results demonstrate that the incorporation of the surface-modified TiO2 nanoparticles can improve the mechanical and thermal properties of nanocomposite coatings. The results also reveal that the surface modification of TiO2 with the HBP chains improves the nanoparticle dispersion, and the coating surface shows a lotus leaf-like microstructure. Thus, the functional nanocomposite coatings exhibit superhydrophobic properties, good photocatalytic depollution performance, and high stripping resistance.

scholarly journals Structural Analysis of Polyhedral Oligomeric Silsesquioxane Coated SiC Nanoparticles and Their Applications in Thermoset Polymers

2015 ◽  
Vol 2015 ◽  
pp. 1-13 ◽  
Author(s):  
Md. Reza-E-Rabby ◽  
Shaik Jeelani ◽  
Vijaya K. Rangari
Keyword(s):  
Photoelectron Spectroscopy ◽  
Polyhedral Oligomeric Silsesquioxane ◽  
Mechanical And Thermal Properties ◽  
Tem Analysis ◽  
Sic Nanoparticles ◽  
X Ray ◽  
Thermoset Resin ◽  
Transmission Electron ◽  
Xrd Techniques ◽  
Oligomeric Silsesquioxane

The SiC nanoparticles (NPs) were sonochemically coated with OctaIsobutyl (OI) polyhedral oligomeric silsesquioxane (POSS) to create a compatible interface between particle and thermoset polymer. X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), and X-ray diffraction (XRD) techniques were used to analyze the structure of OI-POSS coated SiC nanoparticles. These results revealed the formation of a covalent bonding between SiC and OI-POSS. The transmission electron microscopy (TEM) analysis of OI-POSS coated SiC nanoparticles has also shown the indication of attachment between these two nanoparticles. The OI-POSS coated SiC nanoparticles were further reinforced into a thermoset resin system in order to evaluate mechanical and thermal properties of nanocomposites. The flexural strength, modulus, and glass transition temperature were found to be enhanced while SiC and OI-POSS coated SiC were infused into epoxy system compared to those properties of neat epoxy resin.

scholarly journals Zinc Oxide Nanoparticles from Waste Zn-C Battery via Thermal Route: Characterization and Properties

Nanomaterials ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 717 ◽  
Author(s):  
Rifat Farzana ◽  
Ravindra Rajarao ◽  
Pravas Behera ◽  
Kamrul Hassan ◽  
Veena Sahajwalla
Keyword(s):  
Electron Microscopy ◽  
Zno Nanoparticles ◽  
Photoelectron Spectroscopy ◽  
Uv Light ◽  
Inert Atmosphere ◽  
Bet Surface Area ◽  
Visible Range ◽  
Tem Analysis ◽  
Thermal Synthesis ◽  
X Ray

Disposable batteries are becoming the primary sources of powering day-to-day gadgets and consequently contributing to e-waste generation. The emerging e-waste worldwide is creating concern regarding environmental and health issues. Therefore, a sustainable recycling approach of spent batteries has become a critical focus. This study reports the detail characterization and properties of ZnO nanoparticles recovered from spent Zn-C batteries via a facile thermal synthesis route. ZnO nanoparticles are used in many applications including energy storage, gas sensors, optoelectronics, etc. due to the exceptional physical and optical properties. A thermal treatment at 900 °C under an inert atmosphere of argon was applied to synthesize ZnO nanoparticles from a spent Zn-C battery using a horizontal quartz tube furnace. X-ray diffraction (XRD), selected area electron diffraction (SAED) and X-ray photoelectron spectroscopy (XPS) results confirmed the formation of crystalline ZnO nanoparticles. Field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM) analysis confirmed that the size of synthesised ZnO particles were less than 50 nm and mainly composed of sphere shaped nanoparticles. Synthesized ZnO exhibited BET surface area of 9.2629 m2/g and showed absorption of light in the UV region. Excitation of ZnO by UV light showed photoluminescence in the visible range. This study will create an opportunity for potential applications of ZnO nanoparticles from spent batteries and will benefit the environment by reducing the volume of e-waste in landfills.

ROOM TEMPERATURE PHOTOLUMINESCENCE OF POLYCRYSTALLINE SIC PREPARED FROM CARBON-SATURATED SI MELT

2002 ◽  
Vol 16 (06n07) ◽  
pp. 1047-1051
Author(s):  
JIANPING MA ◽  
ZHIMING CHEN ◽  
GANG LU ◽  
MINGBIN YU ◽  
LIANMAO HANG ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Uv Light ◽  
X Ray Diffraction ◽  
X Ray ◽  
Room Temperature Photoluminescence ◽  
Composition And Structure ◽  
Light Excitation ◽  
Scanning Electron

Intense photoluminescence (PL) has been observed at room temperature from the polycrystalline SiC samples prepared from carbon-saturated Si melt at a temperature ranging from 1500 to 1650°C. Composition and structure of the samples have been confirmed by means of X-ray photoelectron spectroscopy, X-ray diffraction and scanning electron microscopy. PL measurements with 325 nm UV light excitation revealed that the room temperature PL spectrum of the samples consists of 3 luminescent bands, the peak energies of which are 2.38 eV, 2.77 eV and 3.06 eV, respectively. The 2.38 eV band is much stronger than the others. It is suggested that some extrinsic PL mechanisms associated with defect or interface states would be responsible to the intensive PL observed at room temperature.

TiO2 anatase nanotubes for the purification of uranium,arsenic and lead containing water: an X-ray Photoelectron Spectroscopy study

2009 ◽  
Vol 1171 ◽  
Author(s):  
Marco Bonato ◽  
Kristin Vala Ragnarsdottir ◽  
Geoffrey C. Allen
Keyword(s):  
Photoelectron Spectroscopy ◽  
Uv Light ◽  
Carbonyl Complexes ◽  
Spectroscopy Study ◽  
High Adsorption ◽  
X Ray ◽  
Tio2 Anatase ◽  
Major Species ◽  
Titania Photocatalyst ◽  
Ph Range

AbstractTiO2 anatase nanotubes synthesised via anodic oxidation were used as adsorbent for the uptake of U and Pb from aqueous solution and the photoremoval of As(III). An X-ray photoelectron spectroscopy study of the sorbent medium surface revealed a high adsorption of U and Pb at pH 8. The adsorption of the uranyl ion was enhanced in an anoxy (N2) atmosphere, because this prevents the formation of very stable carbonyl complexes. As(III) was adsorbed on TiO2 but in the presence of O2 and UV light was oxidized to As(V). XPS analysis revealed that in the pH range 3-9 As(V) was always the major species detected at the surface of the titania photocatalyst.

scholarly journals Influence of Cu(NO3)2 content used in thermal shock method on the photocatalytic activity of Cu-Modified ZnO nanoparticles

2021 ◽  
Vol 5 (3) ◽  
pp. first
Author(s):  
Thế Luân Nguyễn ◽  
Tiến Khoa Lê ◽  
Châu Ngọc Hoàng ◽  
Hữu Khánh Hưng Nguyễn ◽  
Thị Kiều Xuân Huỳnh
Keyword(s):  
Crystal Structure ◽  
Methylene Blue ◽  
Photocatalytic Activity ◽  
Thermal Shock ◽  
Photoelectron Spectroscopy ◽  
Copper Content ◽  
Uv Light ◽  
Copper Nitrate ◽  
X Ray ◽  
Doped Zno

The Cu doped ZnO photocatalysts were prepared on ZnO substrate modified with copper nitrate by thermal shock method with different ratio % molar Cu : Zn = 0.3, 0.5, 1.0, 2.0 and 5.0 in order to study the impacts of copper content on the photocatalytic activity of ZnO under both UV and Vis light irradiation. The crystal structure, morphology bulk and surface were investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). Their photocatalytic activities were studied via time-dependent degradation of methylene blue in aqueous solution. The results exhibit that crystal structure and morphology of Cu doped ZnO photocatalysts is not modified significally than ZnO original but surface charateristicschanged greatly. The photocatalyst was doped with copper content under 2% showed formation of Cu species. These samples perform photocatalytic activity higher than ZnO. The CuNZO-0.05-500 had the highest rate constants for methylene blue degradation (kUV = 6,901 h-1, kVIS = 0,224 h-1), which are about 2.2 times and 1.3 times higher than unmodified ZnO under UV light and Vis light, respectively. However, the CuNZO-5.0-500 which had the formation of CuO phase and unchangeable ZnO's surface has photocatalytic activity similar to pure ZnO.

scholarly journals Surface Study of CuO Nanopetals by Advanced Nanocharacterization Techniques with Enhanced Optical and Catalytic Properties

Nanomaterials ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 1298 ◽  
Author(s):  
Muhammad Arif Khan ◽  
Nafarizal Nayan ◽  
Shadiullah Shadiullah ◽  
Mohd Khairul Ahmad ◽  
Chin Fhong Soon
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalytic Properties ◽  
Average Length ◽  
Tem Analysis ◽  
X Ray ◽  
Surface Study ◽  
Transmission Electron ◽  
One Step ◽  
Controlled Morphology ◽  
Xrd Patterns

In the present work, a facile one-step hydrothermal synthesis of well-defined stabilized CuO nanopetals and its surface study by advanced nanocharacterization techniques for enhanced optical and catalytic properties has been investigated. Characterization by Transmission electron microscopy (TEM) analysis confirmed existence of high crystalline CuO nanopetals with average length and diameter of 1611.96 nm and 650.50 nm, respectively. The nanopetals are monodispersed with a large surface area, controlled morphology, and demonstrate the nanocrystalline nature with a monoclinic structure. The phase purity of the as-synthesized sample was confirmed by Raman spectroscopy and X-ray diffraction (XRD) patterns. A significantly wide absorption up to 800 nm and increased band gap were observed in CuO nanopetals. The valance band (VB) and conduction band (CB) positions at CuO surface are measured to be of +0.7 and −1.03 eV, respectively, using X-ray photoelectron spectroscopy (XPS), which would be very promising for efficient catalytic properties. Furthermore, the obtained CuO nanopetals in the presence of hydrogen peroxide ( H 2 O 2 ) achieved excellent catalytic activities for degradation of methylene blue (MB) under dark, with degradation rate > 99% after 90 min, which is significantly higher than reported in the literature. The enhanced catalytic activity was referred to the controlled morphology of monodispersed CuO nanopetals, co-operative role of H 2 O 2 and energy band structure. This work contributes to a new approach for extensive application opportunities in environmental improvement.

scholarly journals Nickel Supported on AlCeO3 as a Highly Selective and Stable Catalyst for Hydrogen Production via the Glycerol Steam Reforming Reaction

Catalysts ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 411 ◽  
Author(s):  
Nikolaos D. Charisiou ◽  
Georgios I. Siakavelas ◽  
Binlin Dou ◽  
Victor Sebastian ◽  
Steven J. Hinder ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Steam Reforming ◽  
Photoelectron Spectroscopy ◽  
Liquid Product ◽  
Coke Deposition ◽  
Tem Analysis ◽  
X Ray ◽  
Surface Basicity ◽  
Ce Modification ◽  
Temperature Programmed

In this study, a critical comparison between two low metal (Ni) loading catalysts is presented, namely Ni/Al2O3 and Ni/AlCeO3 for the glycerol steam reforming (GSR) reaction. The surface and bulk properties of the catalysts were evaluated using a plethora of techniques, such as N2 adsorption/desorption, Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP–AES), X-ray Diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), Scanning Electron Microscopy / Energy Dispersive X-Ray Spectroscopy (SEM/EDX, Transmission Electron Microscopy (TEM), CO2 and NH3– Temperature Programmed Desorption (TPD), and Temperature Programmed Reduction (H2–TPR). Carbon deposited on the catalyst’s surfaces was probed using Temperature Programmed Oxidation (TPO), SEM, and TEM. It is demonstrated that Ce-modification of Al2O3 induces an increase of the surface basicity and Ni dispersion. These features lead to a higher conversion of glycerol to gaseous products (60% to 80%), particularly H2 and CO2, enhancement of WGS reaction, and a higher resistance to coke deposition. Allyl alcohol was found to be the main liquid product for the Ni/AlCeO3 catalyst, the production of which ceases over 700 °C. It is also highly significant that the Ni/AlCeO3 catalyst demonstrated stable values for H2 yield (2.9–2.3) and selectivity (89–81%), in addition to CO2 (75–67%) and CO (23–29%) selectivity during a (20 h) long time-on-stream study. Following the reaction, SEM/EDX and TEM analysis showed heavy coke deposition over the Ni/Al2O3 catalyst, whereas for the Ni/AlCeO3 catalyst TPO studies showed the formation of more defective coke, the latter being more easily oxidized.

Sign in / Sign up

Export Citation Format

Share Document