scholarly journals Barrier Properties and Characterizations of Poly(lactic Acid)/ZnO Nanocomposites

Molecules ◽  
2020 ◽  
Vol 25 (6) ◽  
pp. 1310 ◽  
Author(s):  
Zhenya Tang ◽  
Fangling Fan ◽  
Zhuangzhuang Chu ◽  
Chunli Fan ◽  
Yuyue Qin
Keyword(s):  
Tensile Strength ◽  
Lactic Acid ◽  
Zno Nanoparticles ◽  
Food Packaging ◽  
Ternary Systems ◽  
Poly Lactic Acid ◽  
Vapor Permeability ◽  
Scanning Calorimetry ◽  
Electron Microscopic ◽  
Nano Zno

This study aimed to reinforce the barrier performance (i.e., oxygen–gas and water–vapor permeability) of poly(lactic acid) (PLA)-based films. Acetyltributylcitrate and zinc oxide nanoparticle (nano-ZnO), serving as plasticizer and nanofiller, respectively, were blended into a PLA matrix through a solvent-volatilizing method. The structural, morphological, thermal, and mechanical performances were then studied. Scanning electron microscopic images showed a significant dispersion of nano-ZnO in PLA ternary systems with low nano-ZnO content. The interaction between PLA matrix and ZnO nanoparticles was further analyzed by Fourier-transform infrared spectroscopy. Wide-angle X-ray scattering spectroscopy demonstrated high compatibility between PLA matrix and ZnO nanoparticles. Mechanical property studies revealed good tensile strength and low flexibility. Differential scanning calorimetry curves proved that an amorphous structure mostly existed in PLA ternary systems. The improvements in barrier property and tensile strength indicated that the PLA/nano-ZnO composite films could be used for food packaging application.

Enhanced properties of poly(lactic acid) by concurrent addition of organo-modified Mg-Al layered double hydroxide (LDH) and triethyl citrate

2019 ◽  
pp. 089270571986827 ◽  
Author(s):  
Mehrnoush Monshizadeh ◽  
Sajad Seifi ◽  
Iman Hejazi ◽  
Javad Seyfi ◽  
Hossein Ali Khonakdar
Keyword(s):  
Lactic Acid ◽  
Layered Double Hydroxide ◽  
Food Packaging ◽  
Synergistic Effects ◽  
Poly Lactic Acid ◽  
Solution Casting ◽  
Scanning Calorimetry ◽  
Concurrent Use ◽  
Triethyl Citrate ◽  
Double Hydroxide

Synergistic effects of organo-modified Mg-Al layered double hydroxide (LDH) and triethyl citrate (TEC) on the properties of poly(lactic acid) (PLA) were demonstrated. PLA/LDH nanocomposites in the absence and presence of TEC were fabricated via solution casting technique. Morphological analysis revealed that as the LDH concentration increases, the number of aggregations is also increased; however, introduction of TEC considerably enhanced the dispersion quality of LDHs. Differential scanning calorimetry results showed that the addition of LDH and TEC had no significant influence on the crystallinity of nanocomposites obtained from solution casting. In contrast, once the samples were cooled from melt, the concurrent use of LDH and TEC led to a dramatic enhancement in the crystallinity of PLA ( X c = 55.5%). Moreover, the LDH nanoparticles counterbalanced the adverse effects of plasticization by TEC leading to enhanced toughness of the final nanocomposites. LDH had also a positive influence on thermal stability of PLA, indicating the heat-insulating role of LDH particles. In conclusion, the concurrent use of LDH and TEC could extend the applicability of PLA especially in food packaging applications.

scholarly journals Multifunctional PLA Blends Containing Chitosan Mediated Silver Nanoparticles: Thermal, Mechanical, Antibacterial, and Degradation Properties

Nanomaterials ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 22 ◽  
Author(s):  
Agueda Sonseca ◽  
Salim Madani ◽  
Gema Rodríguez ◽  
Víctor Hevilla ◽  
Coro Echeverría ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Silver Nanoparticles ◽  
Lactic Acid ◽  
Food Packaging ◽  
Synthesis Method ◽  
Crystallization Rate ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry ◽  
The Matrix ◽  
Degradation Properties

Poly(lactic acid) (PLA) is one of the most commonly employed synthetic biopolymers for facing plastic waste problems. Despite its numerous strengths, its inherent brittleness, low toughness, and thermal stability, as well as a relatively slow crystallization rate represent some limiting properties when packaging is its final intended application. In the present work, silver nanoparticles obtained from a facile and green synthesis method, mediated with chitosan as a reducing and stabilizing agent, have been introduced in the oligomeric lactic acid (OLA) plasticized PLA in order to obtain nanocomposites with enhanced properties to find potential application as antibacterial food packaging materials. In this way, the green character of the matrix and plasticizer was preserved by using an eco-friendly synthesis protocol of the nanofiller. The X-ray diffraction (XRD) and differential scanning calorimetry (DSC) results proved the modification of the crystalline structure as well as the crystallinity of the pristine matrix when chitosan mediated silver nanoparticles (AgCH-NPs) were present. The final effect over the thermal stability, mechanical properties, degradation under composting conditions, and antimicrobial behavior when AgCH-NPs were added to the neat plasticized PLA matrix was also investigated. The obtained results revealed interesting properties of the final nanocomposites to be applied as materials for the targeted application.

Physical Properties and Antimicrobial Activity of a Poly(Lactic Acid)/Poly(Trimethylene Carbonate) Film Incorporated with Thymol

2014 ◽  
Vol 884-885 ◽  
pp. 481-484 ◽  
Author(s):  
Yan Wu ◽  
Ming Wei Yuan ◽  
Ji Yi Yang ◽  
Yu Yue Qin ◽  
Ming Long Yuan ◽  
...  
Keyword(s):  
Antimicrobial Activity ◽  
Lactic Acid ◽  
Water Vapor ◽  
Composite Film ◽  
Food Packaging ◽  
Water Vapor Permeability ◽  
Antimicrobial Activities ◽  
Poly Lactic Acid ◽  
Vapor Permeability ◽  
Trimethylene Carbonate

Thymol (TH), which has antimicrobial effect on many food pathogens, was incorporated as antimicrobial agent into composite poly (lactic acid)/poly (trimethylene carbonate)(PLA-PTMC) films. Antimicrobial active films based on PLA-PTMC were prepared by incorporating thymol at five different concentrations: 0, 3, 6, 9 and 12 %(w/w). The mechanical characterization, water vapor permeability (WVP), and antimicrobial activity of all formulations composite film were carried out. A decrease in elastic modulus was obtained for the active composite film compared with neat PLA-PTMC film. The presence of thymol decreased water vapor permeability, with a significant antimicrobial activity. Antimicrobial activities of films were tested against Escherichia coli, Staphylococcus aurous, Listeria, Bacillus subtilis, and Salmonella. Increasing amount of the thymol in the film caused a significant increase in inhibitory zones. These results suggest that thymol incorporated PLA-PTMC films have a prospectively potential in antimicrobial food packaging.

scholarly journals Effect of chitosan addition in starch and poly(lactic acid) sheets produced by extrusion

2015 ◽  
Vol 6 (1) ◽  
pp. 80
Author(s):  
Matheus Luz Alberti ◽  
Sílvio José De Souza ◽  
Heliberto Gonçalves ◽  
Fabio Yamashita ◽  
Marianne Ayumi Shirai
Keyword(s):  
Lactic Acid ◽  
Water Vapor ◽  
Food Packaging ◽  
Water Vapor Permeability ◽  
Barrier Properties ◽  
Extrusion Process ◽  
Pilot Scale ◽  
Poly Lactic Acid ◽  
Vapor Permeability ◽  
Water Vapor Barrier

<p>The use of blends containing biodegradable polymers like starch and poly (lactic acid) (PLA) has gained considerable attention, especially for the food packaging production. Current research has also highlighted the use of chitosan because their antimicrobial activity, biodegradability and applicability in the production of active biodegradable food packaging. The objective of this work was to produce cassava starch and PLA sheets incorporated with chitosan by flat extrusion process (calendering-extrusion), and evaluate the mechanical, water vapor barrier and microstructural properties. In order to simplify the obtainment of the material reducing processing steps, all components of the blend were homogenized in one step extrusion The incorporation of chitosan in the starch/PLA sheets decreased significantly the tensile strength, Young's modulus, elongation at break and density. In addition, the scanning electron microscopy images showed the formation of non-homogeneous mixtures with the presence of pores between the blend compounds, and this fact affected the water vapor barrier properties increasing water vapor permeability, solubility and diffusion coefficients. It was possible to conclude that although the incorporation of chitosan to the starch/PLA sheets has not contributed to obtain materials with suitable properties, it was able to produce them by calendering-extrusion process in pilot scale. Studies about chitosan incorporation in starch and PLA sheets still needed.</p><p>&nbsp;</p><p>DOI: 10.14685/rebrapa.v6i1.208</p><p>&nbsp;</p>

scholarly journals Physical Properties of Composite Films from Tilapia Skin Collagen with Pachyrhizus Starch and Rambutan Peel Phenolics

Marine Drugs ◽  
2019 ◽  
Vol 17 (12) ◽  
pp. 662
Author(s):  
Yongliang Zhuang ◽  
Shiyan Ruan ◽  
Hanghang Yao ◽  
Yun Sun
Keyword(s):  
Tensile Strength ◽  
Physical Properties ◽  
Food Packaging ◽  
Composite Films ◽  
Water Vapor Permeability ◽  
Amorphous Structure ◽  
Vapor Permeability ◽  
Scanning Calorimetry ◽  
Active Food Packaging ◽  
Skin Collagen

Different composite films composed of tilapia skin collagen (TSC) with Pachyrhizus starch (PS) or rambutan peel phenolics (RPP) were prepared, and the physical properties of these films were determined. The effects of PS and RPP on TSC films were investigated, and our results indicated that PS and RPP could improve the physical properties of TSC films. Opacity and film thickness showed an enhanced trend with increasing PS and RPP contents in TSC films, whereas solubility in water, elongation-at-break (EAB), and water vapor permeability (WVP) showed declining trends. TSC film with 10% PS and 0.5% RPP had the highest tensile strength, and the tensile strength dropped drastically when the content of PS and RPP increased. The light transmittances of the films could decrease with the incorporation of PS and RPP. Differential scanning calorimetry (DSC) demonstrated that the addition of PS and RPP improved the thermal stability of TSC films. In addition, X-ray diffraction indicated that the crystallinity of the films decreased and the amorphous structure of the films tended to become more complex with the addition of PS and RPP. As shown by fourier transform infrared spectroscopy (FTIR) analysis, PS and RPP can strongly interact with TSC, resulting in a modification of its structure. Scanning electron microscope (SEM) analysis showed that there was a good compatibility between TSC, PS, and RPP. The results indicated that TSC film incorporated with 10% PS and 0.5% RPP was an effective method for improve the physical properties of the film. TSC–PS–RPP composite films can be used not only in biomedical applications, but also as active food packaging materials.

scholarly journals Development of Antibacterial Biocomposites Based on Poly(lactic acid) with Spice Essential Oil (Pimpinella anisum) for Food Applications

Polymers ◽  
2021 ◽  
Vol 13 (21) ◽  
pp. 3791
Author(s):  
Negin Noori ◽  
Ali Khanjari ◽  
Mohammadreza Rezaeigolestani ◽  
Ioannis K. Karabagias ◽  
Sahar Mokhtari
Keyword(s):  
Lactic Acid ◽  
Essential Oil ◽  
Food Packaging ◽  
Water Vapor Permeability ◽  
Principal Component ◽  
Poly Lactic Acid ◽  
Vapor Permeability ◽  
Dependent Manner ◽  
Concentration Dependent Manner ◽  
Active Food Packaging

Among the main biodegradable food packaging materials, poly-lactic acid (PLA) is a commercially successful polymer used notably in the food packaging industry. In this study, active PLA films containing different percentage of anise essential oil (AE) (0, 0.5, 1 and 1.5% v/v) were developed, and characterized by physical, mechanical and antibacterial analysis. Based on physical examinations, thermal stability of PLA/AE films was greater than the neat PLA film, and the minimum water vapor permeability (WVP) was recorded for PLA/0.5AE film (1.29 × 10 11 g/m s), while maximum WVP was observed for PLA/1.5AE (2.09 × 1011 g/m s). Moreover, the lightness and yellowness of the composites were decreased by the addition of AE. For the PLA composites with 1.5% AE, the tensile strength decreased by 35% and the elongation break increased by 28.09%, comparing to the pure PLA. According to the antibacterial analysis, the minimum inhibitory concentrations of PLA/AE film were 5 to 100 mg/mL and the active composite could create visible inhibition zones of 14.2 to 19.2 mm. Furthermore, the films containing AE inhibited L. monocytogenes and V. parahaemolyticus in a concentration-dependent manner. The confirmation of the success of the incorporation of EOs into the PLA films was further evaluated using principal component analysis, where positive results were obtained. In this context, our findings suggest the significant potency of AE to be used as an antibacterial agent in active food packaging.

Effect of the talc filler on structural, water vapor barrier and mechanical properties of poly(lactic acid) composites

2016 ◽  
Vol 36 (2) ◽  
pp. 181-188 ◽  
Author(s):  
Aleksandra Buzarovska ◽  
Gordana Bogoeva-Gaceva ◽  
Radek Fajgar
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Water Vapor ◽  
Composite Films ◽  
Water Vapor Permeability ◽  
Barrier Properties ◽  
Poly Lactic Acid ◽  
Vapor Permeability ◽  
Scanning Calorimetry ◽  
Structural Water

Abstract Poly(lactic acid) (PLA) based composite films with different content of talc (5–15 wt%) were prepared by the solvent casting method. The effect of talc on morphological, structural, thermal, barrier and mechanical properties of neat PLA was investigated. The PLA/talc composites revealed a polymorphic crystalline structure, as demonstrated by X-ray diffraction (XRD) study and differential scanning calorimetry (DSC) analysis. The PLA/talc composites also exhibited significantly improved barrier properties (up to 55% compared to neat PLA), as shown by water vapor permeability (WVP) tests. The puncture measurements showed improved mechanical properties at lower content of talc (up to 5 wt%), and increased brittleness of the PLA/talc composite films at higher talc concentrations.

Synergistic effect of carbon nanoparticles on the mechanical and thermal properties of poly(lactic acid) as promising systems for packaging

2020 ◽  
Vol 54 (27) ◽  
pp. 4133-4144
Author(s):  
Anne Caroline da Silva Rocha ◽  
Lívia Rodrigues Menezes ◽  
Emerson Oliveira da Silva ◽  
Maria Clara Guimarães Pedrosa
Keyword(s):  
Lactic Acid ◽  
Environmental Impact ◽  
Synergistic Effect ◽  
Polymer Nanocomposites ◽  
Carbon Nanoparticles ◽  
Food Packaging ◽  
Ternary Systems ◽  
Poly Lactic Acid ◽  
Mechanical Resistance ◽  
Mechanical And Thermal Properties

Due to the high demand of the use of food packaging in the present day, the waste from the material disposal has become a problem of high environmental impact. In this perspective, biodegradable polymers can represent a viable alternative as they degrade after their disposal, thus reducing their environmental impact. The poly(lactic acid) or polylactide is a biodegradable, biocompatible, and compostable polymer, being considered by many authors as one of the most promising biopolymers in industrial applications. However, its low thermal and mechanical properties make it an unfeasible option to replace synthetic polymers. Consequently, polymer nanocomposites containing carbon nanoparticles are products of relevant interest currently, mainly due to the thermal, mechanical, electrical, and optical properties these materials can present. Therefore, carbon nanoparticles (carbon nanotubes, graphene, and fullerene) modified with octadecylamine in their isolated state and in ternary systems in concentrations of 0.01%, 0.03%, and 0.09% were obtained from poly(lactic acid) polymer nanocomposites. After obtaining them, these systems were analyzed by TGA, DSC, FTIR, XRD, SEM, DMA, and NMR techniques. The presence of the octadecylamine modified carbon nanoparticles was able to increase the thermal and mechanical resistance of the poly(lactic acid) matrix. The systems with 0.03% of the nanostructures showed better results in both analyses. In the system with 0.09%, agglomeration occurred, and in ternary systems, the application of these particles results in a greater impact on the molecular mobility exhibiting a synergistic effect that may come from a better dispersion.

Preparation and characterization of poly(lactic acid)/sisal fiber bio-composites under continuous elongation flow

2018 ◽  
Vol 39 (1) ◽  
pp. 76-84 ◽  
Author(s):  
Yongbin Tan ◽  
Xiaoqiu Zhang ◽  
Jin-ping Qu
Keyword(s):  
Lactic Acid ◽  
Extrusion Direction ◽  
Tensile Modulus ◽  
Mechanical Tests ◽  
Sisal Fiber ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry ◽  
Electron Microscopic ◽  
The Matrix ◽  
Elongation Flow

AbstractIn this study, poly(lactic acid) (PLA) matrix bio-composites reinforced with various quantities of sisal fibers (SFs) (from 10% to 50% in weight) were fabricated by using a self-made vane mixer, which can generate continuous elongation flow. The morphology, crystallization, and mechanical properties of PLA/SF bio-composites under continuous elongation flow were investigated. Scanning electron microscopic images showed that SFs were uniformly dispersed in the matrix and oriented along the extrusion direction. Meanwhile, it was found that the diameter of SFs decreased from 250 to 20 μm, which certified that continuous elongation flow remarkably affected the separation of elementary fibers from fiber bundles. Wide-angle X-ray diffraction and differential scanning calorimetry measurements indicated that the addition of SFs promoted the crystallization of PLA as well as increased the crystallinity of PLA. The mechanical tests exhibited that both impact strength and tensile modulus were significantly enhanced (about 64% and 94.63%, respectively) with SFs loading at 40%, which was due to the well dispersion and separation of elementary fibers.

Sign in / Sign up

Export Citation Format

Share Document