scholarly journals Phase Transitions in the α–γ–β Spodumene Thermodynamic System and Impact of γ-Spodumene on the Efficiency of Lithium Extraction by Acid Leaching

Minerals ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 519
Author(s):  
Colin Dessemond ◽  
Gervais Soucy ◽  
Jean-Philippe Harvey ◽  
Philippe Ouzilleau
Keyword(s):  
Heat Treatment ◽  
Particle Size ◽  
Extraction Efficiency ◽  
Mechanical Energy ◽  
Acid Leaching ◽  
Thermodynamic System ◽  
Coarse Fraction ◽  
X Ray ◽  
Heat Treated ◽  
Lower Heat

Heat-treatment of spodumene concentrate at 1323 K (1050 °C) for 30 min in a rotary kiln yielded a successful decrepitation. Particle size decreased from 2 cm to less than 425 µm for 80% of the initial mass. X-ray analysis of both fractions did not reveal the presence of α-spodumene or γ-spodumene. The coarse fraction was ground to less than 425 µm with minimal mechanical energy and mixed with the finer fraction to perform lithium extraction. The lithium extraction efficiency reached 98 wt% without the need for flotation. Some aspects of the thermodynamic behavior of the spodumene system were assessed. Results show that metastable γ-spodumene may hinder the formation of β-spodumene at lower heat treatment temperatures. Some heat-treated samples presented non-negligible γ-spodumene content and lithium extraction efficiency decreases as the γ content increases. Finally, the assumed irreversibility of the transformations was studied by analyzing heat-treated samples following long controlled-storage periods. The results show that concentrate composition is not static over the studied time. This suggests that the β formation is not as irreversible as claimed. It is recommended to avoid long periods between heat-treatment and extraction to avoid the slow conversion of β-spodumene to other allotropes, which are less susceptible to lithium extraction.

scholarly journals Modulation of Lithium Disilicate Translucency through Heat Treatment

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2094
Author(s):  
Seok-Ki Jung ◽  
Dae Woon Kim ◽  
Jeongyol Lee ◽  
Selvaponpriya Ramasamy ◽  
Hyun Sik Kim ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Particle Size ◽  
Light Scattering ◽  
Flexural Strength ◽  
Control Method ◽  
Light Transmission ◽  
Lithium Disilicate ◽  
Lower Heat ◽  
Average Size ◽  
Ball Test

The aim of this study was to present a control method for modulating the translucency of lithium disilicate ceramics through thermal refinement. Identical lithium disilicate blocks were thermally refined using four different heat treatment schedules, and the microstructure, translucency, and flexural strength of the ceramics were investigated in detail by SEM, spectroscopy, and a piston-on-three-ball test. The results showed that ceramics treated under higher heat had larger grains, with an average size between 240 and 1080 nm. In addition, a higher transmittance of all wavelengths was observed in ceramics treated under lower heat, and the transmittance in the 550 nm wavelength ranged from 27 to 34%. The results suggest that the translucency of ceramics can be modified through thermal refinement under two conditions: (1) the particle size of the ceramic is small enough to achieve minimal grain-boundary light scattering, and (2) the percentage of particles allowing visible light transmission is altered by the heat treatment.

Hardening of Selective Laser Melted M2 Steel

2021 ◽  
Author(s):  
Mei Yang ◽  
Yishu Zhang ◽  
Haoxing You ◽  
Richard Smith ◽  
Richard D. Sisson
Keyword(s):  
Heat Treatment ◽  
High Speed ◽  
Cutting Tools ◽  
High Speed Steel ◽  
High Hardness ◽  
Steel Part ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heat Treated ◽  
Near Net Shape

Abstract Selective laser melting (SLM) is an additive manufacturing technique that can be used to make the near-net-shape metal parts. M2 is a high-speed steel widely used in cutting tools, which is due to its high hardness of this steel. Conventionally, the hardening heat treatment process, including quenching and tempering, is conducted to achieve the high hardness for M2 wrought parts. It was debated if the hardening is needed for additively manufactured M2 parts. In the present work, the M2 steel part is fabricated by SLM. It is found that the hardness of as-fabricated M2 SLM parts is much lower than the hardened M2 wrought parts. The characterization was conducted including X-ray diffraction (XRD), optical microscopy, Scanning Electron Microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS) to investigate the microstructure evolution of as-fabricated, quenched, and tempered M2 SLM part. The M2 wrought part was heat-treated simultaneously with the SLM part for comparison. It was found the hardness of M2 SLM part after heat treatment is increased and comparable to the wrought part. Both quenched and tempered M2 SLM and wrought parts have the same microstructure, while the size of the carbides in the wrought part is larger than that in the SLM part.

Study of Raman Spectroscopy on Graphene Phase from Heat Treatment of Coconut (Cocus nucifera) Shell

2015 ◽  
Vol 827 ◽  
pp. 290-293 ◽  
Author(s):  
Fandi Angga Prasetya ◽  
Muhammad Nasrullah ◽  
Ananda Yogi Nugraheni ◽  
Darminto
Keyword(s):  
Heat Treatment ◽  
Raman Spectroscopy ◽  
Atmospheric Condition ◽  
Peak Position ◽  
Special Treatment ◽  
Distilled Water ◽  
X Ray ◽  
Heat Treated ◽  
Reduced Graphene ◽  
Two Samples

Coconut (Cocus Nucifera) shell as the main ingredient in this research has been heat-treated at temperature of 1000°C in atmospheric condition aiming to obtain the expected phase of graphene. After heat treatment, an additional special treatment was given, where sample was then rinsed with distilled water. Furthermore, the heated coconut shell was characterized by Raman Spectroscopy (785 nm) and X-ray diffractometry. Based on the treatment and characterization conducted, all samples were likely to contain reduced graphene oxide (RGO) phase.The XRD data have supported the existence of RGO with the diffraction peak position (2q) at 25o and 45o. Evidence is also given by the result of Raman Spectroscopy which produces peaks (denoted by D and G bands) located at wave numbers of 1300 cm-1 and 1590 cm-1. The value of the ratio ID/IG of the two samples in the figures are 2.6 and 2.51 (matched with ratio ID/IG of RGO). The ID/IG ratio of sample which was rinsed by distilled water is higher that those without rinsing treatment.

EFFECT OF HEAT TREATMENT ON MICROSTRUCTURE AND CORROSION RESISTANCE OF Ni-B-W-Mo COATING DEPOSITED BY ELECTROLESS METHOD

2018 ◽  
Vol 25 (08) ◽  
pp. 1950023 ◽  
Author(s):  
ARKADEB MUKHOPADHYAY ◽  
TAPAN KUMAR BARMAN ◽  
PRASANTA SAHOO
Keyword(s):  
Heat Treatment ◽  
Corrosion Resistance ◽  
Electrochemical Techniques ◽  
Sodium Molybdate ◽  
Medium Carbon Steel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Solid Solution Strengthening ◽  
Heat Treated ◽  
Electroless Coatings

The present work reports the deposition of a quaternary Ni-B-W-Mo coating on AISI 1040 medium carbon steel and its characterization. Quaternary deposits are obtained by suitably modifying existing electroless Ni-B bath. Composition of the as-deposited coating is analyzed by energy dispersive X-ray spectroscopy. The structural aspects of the as-deposited and coatings heat treated at 300[Formula: see text]C, 350[Formula: see text]C, 400[Formula: see text]C, 450[Formula: see text]C and 500[Formula: see text]C are determined using X-ray diffraction technique. Surface of the as-deposited and heat-treated coatings is examined using a scanning electron microscope. Very high W deposition could be observed when sodium molybdate is present in the borohydride-based bath along with sodium tungstate. The coatings in their as-deposited condition are amorphous while crystallization takes place on heat treatment. A nodulated surface morphology of the deposits is also observed. Vickers’ microhardness and crystallite size measurement reveal inclusion of W and Mo results in enhanced thermal stability of the coatings. Solid solution strengthening of the electroless coatings by W and Mo is also observed. The applicability of kinetic strength theory to the hardening of the coatings on heat treatment is also investigated. Corrosion resistance of Ni-B-W-Mo coatings and effect of heat treatment on the same are also determined by electrochemical techniques.

scholarly journals Preparation and Assessment of Heat-Treated α-Chitin Nanowhiskers Reinforced Poly(viny alcohol) Film for Packaging Application

Materials ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 1883 ◽  
Author(s):  
Chao Peng ◽  
Guangxue Chen
Keyword(s):  
Heat Treatment ◽  
Composite Films ◽  
Barrier Properties ◽  
Mechanical Tests ◽  
Light Transmittance ◽  
Poly Vinyl Alcohol ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heat Treated ◽  
Chitin Nanowhiskers

In this study, poly(vinyl alcohol) (PVA) composite films enhanced by α-chitin nanowhiskers (ChWs) were prepared through heat treatment. The obtained membranes were assessed by means of FTIR spectroscopy, X-ray diffraction, thermogravimetric analysis, regular light transmittance, mechanical tests, permeability and water absorption. The influence of the nano-component and heat treatment on the mechanical, thermal and water-resistant properties of the composite membrane were analyzed. From the results of the work, the produced films with excellent barrier properties and inexpensive raw processed materials have great prospects in packaging applications.

Magnetization and XRD Studies of Laser Heat Treated SmCo5 Powders

2021 ◽  
Vol 1016 ◽  
pp. 1299-1304
Author(s):  
Naidu Seetala ◽  
Deidre Henderson ◽  
Jumel Jno-Baptiste ◽  
Hao Wen ◽  
Sheng Min Guo
Keyword(s):  
Heat Treatment ◽  
Hydrogen Gas ◽  
Vacuum Furnace ◽  
X Ray Diffraction ◽  
X Ray ◽  
Micro Particles ◽  
Laser Heat ◽  
Heat Treated ◽  
Xrd Studies ◽  
Hydride Phases

The microstructure and magnetization of SmCo5 micro-particles may be used as feedstock for 3D printing to make miniature strong magnets. Thus, the magnetic response and microstructures of commercially available SmCo5 micro-particles were studied under various heat treatments using a high wattage laser. The magnetization of laser heat treated powders at 50-watt showed an increase in magnetization, while the 75-watt melt showed a little to no change. Unfortunately, the coercivity of both laser heat treated samples decreased significantly. Oxidation during the heat treatment is suspected to result in low coercivity. Purging with argon-gas prior to laser heating showed improved coercivity. To further minimize the oxidation problem a set of SmCo5 powder was reduced prior to laser heat treatment using a constant flow of hydrogen gas while being heated at various temperatures from 100 oC to 400 oC for a period of ~4 hours. The results show that the magnetization generally increases with the temperature, while the coercivity decreases significantly. Another set of SmCo5 was annealed in a vacuum furnace for one hour at temperatures between 200 oC and 400 oC in order to confirm that no hydride phases were formed during reduction. The magnetization and coercivity showed similar variations with annealing temperature to those for the reduced powders confirming that these variations may be due to change in crystal structure rather than formation of hydrides. X-ray Diffraction (XRD) studies were performed to identify the changes in crystal phases.

Copper(I) Halide Nanoparticle-dispersed Glasses Prepared by Copper Staining

2005 ◽  
Vol 20 (9) ◽  
pp. 2480-2485 ◽  
Author(s):  
Kohei Kadono ◽  
Tatsuya Suetsugu ◽  
Takeshi Ohtani ◽  
Toshihiko Einishi ◽  
Takashi Tarumi ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Surface Region ◽  
Borosilicate Glasses ◽  
X Ray Diffraction ◽  
X Ray ◽  
Depth Profiles ◽  
Transmission Electron ◽  
Heat Treated ◽  
Glass Heat

Copper(I) chloride and bromide nanoparticle-dispersed glasses were prepared by means of a conventional copper staining. The staining was performed by the following process: copper stain was applied on the surfaces of Cl−- or Br−-ion-containing borosilicate glasses, and the glasses were heat-treated at 510 °C for various times. Typical exciton bands observed in the absorption spectra of the glasses after the heat treatment indicated that CuCl and CuBr particles were formed in the surface region of the glasses. The average sizes of the CuCl and CuBr particles in the glasses heat-treated for 48 h were estimated at 4.8 and 2.7 nm, respectively. The nanoparticles were also characterized by x-ray diffraction and transmission electron microscopy. Depth profiles of Cu and CuBr concentration in the glass heat-treated for 48 h were measured. Copper decreased in concentration monotonously with depth, reaching up to 60 μm, while the CuBr concentration had a maximum at about 25 μm in depth.

Recent Applications of XSA in Heat Treatment and Fatigue of Steels

1983 ◽  
Vol 27 ◽  
pp. 179-190
Author(s):  
E. Macherauch ◽  
B. Scholtes
Keyword(s):  
Heat Treatment ◽  
Residual Stresses ◽  
Experimental Work ◽  
Carbon Steels ◽  
X Ray ◽  
Lattice Strains ◽  
Heat Treated ◽  
Computer Controlled

This paper is intended to give an exemplary review of recent investigations performed in the X-ray laboratory of the Institut für Werkstoffkunde I of the Universität Karlsruhe, FRG, concerning particular problems of residual stresses of heat-treated and fatigued steels. The experimental work was mainly performed with computer-controlled Karlsruhe type ψ-diffractometers. If linear distributions of residual lattice strains occurred the sin2ψ-method was applied to determine residual stresses. The experiments were performed with plain carbon steels of 0.22 and 0.45 wt.-% carbon (German grade Ck 22 and Ck 45) and some low alloyed steels.

Semiquantitative Analysis by X-Ray Powder Diffraction (SQXRD) of the < 2 mm to 0.002 mm and < 0.002 mm Fractions of Soil

1988 ◽  
Vol 3 (3) ◽  
pp. 144-152 ◽  
Author(s):  
G. A. Raab
Keyword(s):  
Particle Size ◽  
Clay Fraction ◽  
Internal Standard ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heat Treated ◽  
Freeze Dried ◽  
Strict Protocol ◽  
Attention To Detail

AbstractThe method described in this paper is a strict protocol for X-ray diffraction (XRD) analysis of mineral phases found in soils. Its application is not restricted to soils and is an attempt to standardize XRD sample preparation and analysis. The protocol requires the particle size of the < 2 mm - 0.002 mm fraction be reduced to 0.002 mm before analysis. In die qualitative section, the clay fraction ( < 0.002 mm particle size) is prepared as oriented slides. The suspended clay fraction is saturated with ethylene glycol, K +, and Mg+2; pipeted; air-dried; heat-treated at 110°C, 350°C, and 550°C; and X-rayed at each step in order to properly identify the clay minerals. In the quantitative section, the method employs a matrix-flushing agent, corundum (Al2O3). The corundum acts also as an internal standard, a calibration standard, and a reference standard. The suspended clay fraction is freeze-dried and corundum is added to each sample. Randomly oriented powder mounts are prepared from the < 2 mm - 0.002 mm fraction, and the < 0.002 mm fraction, and X-rayed. A series of reference standards are prepared based on the existing mineralogy, corundum is added, and each mixture is X-rayed. The software integrates the area under specific peaks (chosen for intensity and no overlap) in each sample, calculates the reference intensity ratios (RIRs) and calculates the percentage of each mineral based on the equation of Chung (1974). The attention to detail allows documentation and verification of the results yielding data of known quality.

scholarly journals Heat Treatment Effect on Eu3+ Doped TeO2-BaO-Bi2O3 Glass Systems with Ag Nanoparticles

2017 ◽  
Vol 2017 ◽  
pp. 1-12 ◽  
Author(s):  
Tomasz Lewandowski ◽  
Michał Dembski ◽  
Michalina Walas ◽  
Marcin Łapiński ◽  
Magdalena Narajczyk ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Silver Nanoparticles ◽  
Photoelectron Spectroscopy ◽  
Rare Earth Ions ◽  
Molar Ratio ◽  
Excitation Wavelength ◽  
X Ray ◽  
Dsc Measurements ◽  
Heat Treated ◽  
Luminescence Measurement

Glass systems of 73TeO2-4BaO-3Bi2O3-2Eu2O3-xAg (in molar ratio where x = 0, 1, 2, and 3) compositions have been successfully synthesized. Silver nanoparticles were obtained with the employment of heat treatment (HT) procedure executed at 350°C. Glass transition temperatures of different compositions have been determined through DSC measurements. XRD results presented characteristic amorphous halo indicating lack of long range order in the samples. FTIR structural studies revealed that glass matrix is mainly composed of TeO3 and TeO4 species and is stable after different applied heat treatment times. X-ray photoelectron spectroscopy (XPS) measurements confirmed that in selected samples part of Ag ions changed oxidation state to form Ag0 species. TEM measurements revealed nanoparticles of size in the range of 20–40 nm. UV-vis absorption results demonstrated characteristic transitions of Eu3+ ions. Additionally, UV-vis spectra of samples heat-treated for 6, 12, 24, and 48 hours presented bands related to silver nanoparticles. Photoluminescence (PL) studies have been performed with excitation wavelength of λexc=395 nm. Obtained spectra exhibited peaks due to 5D0-7FJ (where J=2,3,4) and 5D1-7FJ (where J=1,2,3) transitions of Eu3+. Moreover, luminescence measurement indicated enhancement of rare earth ions emissions in several of the annealed samples. Increase of emission intensity of about 35% has been observed.

Sign in / Sign up

Export Citation Format

Share Document