scholarly journals Three-Dimensional Electro-Sonic Flow Focusing Ionization Microfluidic Chip for Mass Spectrometry

Micromachines ◽  
2015 ◽  
Vol 6 (12) ◽  
pp. 1890-1902 ◽  
Author(s):  
Cilong Yu ◽  
Xiang Qian ◽  
Yan Chen ◽  
Quan Yu ◽  
Kai Ni ◽  
...  
2021 ◽  
Author(s):  
Farbod Ahmadzadeh

Soft lithography techniques has been used widely in the past decade to fabricate microfluidic chips used in biomedical applications. Abrasive jet machining (AJM) has been used to fabricate similar chips using particle erosion mechanisms. This thesis proposes a new technique using a UV light sensitive self-adhesive mask (RapidMask) and AJM to fabricate a three dimensional flow focusing microfluidic chip where the depth of the channel is allowed to vary along the channel length. A detailed characterization of the effect of curing parameters of a UV light curing self-adhesive mask on the resulting feature resolution is reported. Instead of relying on the manufacturer recommended curing parameters which were vaguely described for specific UV curing units, it was found that measured energy density could be used to quantify a recommended cure that is independent of the curing unit. The best achievable pattern on borosilicate glass using RM and AJM was found and reported along with the erosion rates of uncured, cured RM during AJM. A new methodology was introduced to use multiple layers of the RM in order to increase the achievable feature aspect ratio. The results of the RM curing and multiple layer investigation were then used to fabricate a three dimensional flow focusing chip with a varying depth at the focusing junction. The chip was then sealed and tested to demonstrate its capabilities and potential in healthcare and biomedical applications. To the best knowledge of the author, this thesis is the first to report using a double layer RM to fabricate a microfluidic chip using AJM.


2021 ◽  
Author(s):  
Farbod Ahmadzadeh

Soft lithography techniques has been used widely in the past decade to fabricate microfluidic chips used in biomedical applications. Abrasive jet machining (AJM) has been used to fabricate similar chips using particle erosion mechanisms. This thesis proposes a new technique using a UV light sensitive self-adhesive mask (RapidMask) and AJM to fabricate a three dimensional flow focusing microfluidic chip where the depth of the channel is allowed to vary along the channel length. A detailed characterization of the effect of curing parameters of a UV light curing self-adhesive mask on the resulting feature resolution is reported. Instead of relying on the manufacturer recommended curing parameters which were vaguely described for specific UV curing units, it was found that measured energy density could be used to quantify a recommended cure that is independent of the curing unit. The best achievable pattern on borosilicate glass using RM and AJM was found and reported along with the erosion rates of uncured, cured RM during AJM. A new methodology was introduced to use multiple layers of the RM in order to increase the achievable feature aspect ratio. The results of the RM curing and multiple layer investigation were then used to fabricate a three dimensional flow focusing chip with a varying depth at the focusing junction. The chip was then sealed and tested to demonstrate its capabilities and potential in healthcare and biomedical applications. To the best knowledge of the author, this thesis is the first to report using a double layer RM to fabricate a microfluidic chip using AJM.


2021 ◽  
Vol 25 (3) ◽  
Author(s):  
Xiaofei Yuan ◽  
Andrew Glidle ◽  
Hitoshi Furusho ◽  
Huabing Yin

AbstractOptical-based microfluidic cell sorting has become increasingly attractive for applications in life and environmental sciences due to its ability of sophisticated cell handling in flow. The majority of these microfluidic cell sorting devices employ two-dimensional fluid flow control strategies, which lack the ability to manipulate the position of cells arbitrarily for precise optical detection, therefore resulting in reduced sorting accuracy and purity. Although three-dimensional (3D) hydrodynamic devices have better flow-focusing characteristics, most lack the flexibility to arbitrarily position the sample flow in each direction. Thus, there have been very few studies using 3D hydrodynamic flow focusing for sorting. Herein, we designed a 3D hydrodynamic focusing sorting platform based on independent sheath flow-focusing and pressure-actuated switching. This design offers many advantages in terms of reliable acquisition of weak Raman signals due to the ability to precisely control the speed and position of samples in 3D. With a proof-of-concept demonstration, we show this 3D hydrodynamic focusing-based sorting device has the potential to reach a high degree of accuracy for Raman activated sorting.


The Analyst ◽  
2015 ◽  
Vol 140 (20) ◽  
pp. 6955-6963 ◽  
Author(s):  
Xing Zhang ◽  
Yehia M. Ibrahim ◽  
Tsung-Chi Chen ◽  
Jennifer E. Kyle ◽  
Randolph V. Norheim ◽  
...  

Novel μFAIMS/IMS-MS three dimensional separations were optimized to enhance separation power and selectivity in biological analyses.


2017 ◽  
Vol 14 (12) ◽  
pp. 1139-1140 ◽  
Author(s):  
Klaus Dreisewerd ◽  
Joanne Y Yew

Sign in / Sign up

Export Citation Format

Share Document