scholarly journals Endless Single-Mode Photonics Crystal Fiber Metalens for Broadband and Efficient Focusing in Near-Infrared Range

Micromachines ◽  
2021 ◽  
Vol 12 (2) ◽  
pp. 219
Author(s):  
Qiancheng Zhao ◽  
Jiaqi Qu ◽  
Gangding Peng ◽  
Changyuan Yu
Keyword(s):  
Near Infrared ◽  
Focal Length ◽  
Single Mode ◽  
Infrared Range ◽  
Fiber Communication ◽  
Crystal Fiber ◽  
Phase Profile ◽  
Wide Wavelength Range ◽  
Mode Area ◽  
Near Infrared Range

The advent of the ‘lab-on-fiber’ concept has boosted the prosperity of optical fiber-based platforms integrated with nanostructured metasurface technology which are capable of controlling the light at the nanoscale for multifunctional applications. Here, we propose an endless single-mode large-mode-area photonic crystal fiber (LMA-PCF) integrated metalens for broadband and efficient focusing from 800 to 1550 nm. In the present work, the optical properties of the substrate LMA-PCF were investigated, and the metalens, consisting of dielectric TiO2 nanorods with varying radii, was elaborately designed in the fiber core region with a diameter of 48 μm to cover the required phase profile for efficient focusing with a high transmission. The focusing characteristics of the designed metalens were also investigated in detail over a wide wavelength range. It is shown that the in-fiber metalens is capable of converging the incident beams into the bright, symmetric, and legible focal spots with a large focal length of 315–380 μm depending on the operating wavelength. A high and average focusing efficiency of 70% was also obtained with varying wavelengths. It is believed the proposed fiber metalens may show great potential in applications including fiber laser configuration, machining, and fiber communication.

scholarly journals Accurately Shaping Supercontinuum Spectrum via Cascaded PCF

Sensors ◽  
2020 ◽  
Vol 20 (9) ◽  
pp. 2478
Author(s):  
Jifang Rong ◽  
Hua Yang ◽  
Yuzhe Xiao
Keyword(s):  
Photonic Crystal ◽  
Pump Power ◽  
Near Infrared ◽  
Cost Effective ◽  
Infrared Range ◽  
Crystal Fiber ◽  
Red Edge ◽  
Supercontinuum Spectrum ◽  
Cost Effective Alternative ◽  
Near Infrared Range

Shaping is very necessary in order to obtain a wide and flat supercontinuum (SC). Via numerical simulations, we accurately demonstrated shaping the SC using the fiber cascading method to significantly increase the width as well as the flatness of the spectrum in silica photonic crystal fiber (PCF). The cascaded PCF contains two segments, each of which has dual zero-dispersion frequencies (ZDFs). The spectral range of the SC can be expanded tremendously by tuning the spacing between the two ZDFs of the first segmented cascaded PCF. Increasing the pump power generates more solitons at the red edge, which accelerates solitons trapping and improves the spectral flatness of the blue edge. Furthermore, cascading the second segmented PCF by choosing appropriate fiber parameters ensures the flatness of the red end of SC. Therefore, a cost-effective alternative method for broad and flat supercontinuum generation in the near-infrared range is proposed here, which can be implemented easily in any photonics laboratory, where dual ZDFs PCFs are commonly found.

Coupling of Er light emissions to plasmon modes on In2O3: Sn nanoparticle sheets in the near-infrared range

2014 ◽  
Vol 105 (4) ◽  
pp. 041903 ◽  
Author(s):  
Hiroaki Matsui ◽  
Wasanthamala Badalawa ◽  
Takayuki Hasebe ◽  
Shinya Furuta ◽  
Wataru Nomura ◽  
...  
Keyword(s):  
Near Infrared ◽  
Infrared Range ◽  
Near Infrared Range ◽  
Sn Nanoparticle ◽  
Plasmon Modes

scholarly journals Fabrication of Dy2O3 Transparent Ceramics by Vacuum Sintering Using Precipitated Powders

2020 ◽  
Vol 7 (1) ◽  
pp. 6
Author(s):  
Dianjun Hu ◽  
Xin Liu ◽  
Ziyu Liu ◽  
Xiaoying Li ◽  
Feng Tian ◽  
...  
Keyword(s):  
Near Infrared ◽  
Optical Quality ◽  
Precipitation Method ◽  
Infrared Range ◽  
Transparent Ceramics ◽  
Vacuum Sintering ◽  
Hydrogen Carbonate ◽  
Ammonium Hydrogen ◽  
Liquid Precipitation ◽  
Near Infrared Range

As a kind of promising material for a Faraday isolator used in the visible and near infrared range, Dy2O3 transparent ceramics were prepared by vacuum sintering from the nano-powders synthesized by the liquid precipitation method using ammonium hydrogen carbonate as precipitant with no sintering aids. The synthesized precursor was calcinated at 950 °C–1150 °C for 4 h in air. The influences of the calcination temperature on the morphologies and phase composition of Dy2O3 powders were characterized. It is found that the Dy2O3 powder calcinated at 1000 °C for 4 h is superior for the fabrication of Dy2O3 ceramics. The Dy2O3 transparent ceramic sample prepared by vacuum sintering at 1850 °C for 10 h, and subsequently with air annealing at 1400 °C for 10 h, from the 1000 °C-calcined Dy2O3 powders, presents the best optical quality. The values of in-line transmittance of the optimal ceramic specimen with the thickness of 1.0 mm are 75.3% at 2000 nm and 67.9% at 633 nm. The Verdet constant of Dy2O3 ceramics was measured to be −325.3 ± 1.9 rad/(T·m) at 633 nm, about 2.4 times larger than that of TGG (Tb3Ga5O12) single crystals.

scholarly journals Joint Measurements of PM<sub>2.5</sub> and light-absorptive PM in woodsmoke-dominated ambient and plume environments

2017 ◽  
Author(s):  
K. Max Zhang ◽  
Bo Yang ◽  
Geng Chen ◽  
Jiajun Gu ◽  
James Schwab ◽  
...  
Keyword(s):  
Near Infrared ◽  
Uv Light ◽  
Operating Conditions ◽  
Infrared Range ◽  
Wood Combustion ◽  
Near Ultraviolet ◽  
Linear Relationships ◽  
Saranac Lake ◽  
Near Infrared Range ◽  
Strong Linear Relationship

Abstract. DC, also referred to as Delta-C, measures enhanced light absorption of particulate matter (PM) samples at the near-ultraviolet (UV) range relative to the near-infrared range, which has been proposed previously as a woodsmoke marker due to the presence of enhanced UV light absorbing materials from wood combustion. In this paper, we further evaluated the applications and limitations of using DC as both a qualitative and semi-quantitative woodsmoke marker via joint continuous measurements of PM2.5 (by nephelometer pDR-1500) and light-absorptive PM (by 2-wavelength and 7-wavelength Aethalometer®) in three Northeastern U.S. cities/towns including Rutland, VT, Saranac Lake, NY and Ithaca, NY. We compared the pDR-1500 against a FEM PM2.5 sampler (BAM 1020), and identified a close agreement between the two instruments in a woodsmoke-dominated ambient environment. The analysis of seasonal and diurnal trends of DC, BC (880 nm) and PM2.5 concentrations supports the use of DC as an adequate qualitative marker. The strong linear relationships between PM2.5 and DC in both woodsmoke-dominated ambient and plume environments suggest that DC can reasonably serve as a semi-quantitative woodsmoke marker. We proposed a DC-based indicator for woodsmoke emission, which was then shown to exhibit relatively strong linear relationship with heating demand. While we observed reproducible PM2.5-DC relationships in similar woodsmoke-dominated ambient environments, those relationships differ significantly with different environments, and among individual woodsmoke sources. DC correlated much more closely with PM2.5 than EcoChem PAS2000-reported PAH in woodsmoke-dominated ambient environments. Our analysis also indicates the potential for PM2.5-DC relationships to be utilized to distinguish different combustion and operating conditions of woodsmoke sources, and that DC-Heating demand relationships could be adopted to estimate woodsmoke emissions. However, future studies are needed to elucidate those relationships.

scholarly journals Interaction in quasibinary systems based on TlSbP2Se6 and compounds of the Tl2Se-Sb2Se3 system

2019 ◽  
Vol 85 (3) ◽  
pp. 20-26
Author(s):  
Viktoria Sabov ◽  
Мaria Potorij ◽  
Iwan Kityk ◽  
Mykhailo Filep ◽  
Marian Sabov
Keyword(s):  
Cross Sections ◽  
Near Infrared ◽  
Practical Interest ◽  
Infrared Range ◽  
Thermally Stable ◽  
Quaternary Compound ◽  
Metal Compounds ◽  
Temperature Method ◽  
The Family ◽  
Near Infrared Range

Complex chalcogenides display semiconductor properties. In particular, heavy metal compounds that are formed in the Tl2Se-Sb2Se3 system are good thermoelectric materials. At the same time TlSbP2Se6 compound belongs to the family of hexaseleno-hypodiphosphates, which representatives have a number of interesting properties (optoelectric, non-linear, etc.) in the near infrared range. The combination of these properties in one material causes some scientific and practical interest, therefore our research was aimed to study the nature of the interaction between TlSbP2Se6 and the thermally stable phases of the Tl2Se-Sb2Se3 system in order to find new promising candidate for applications in electronic devices. The alloys were prepared from corresponding binary, ternary compounds and quaternary TlSbP2Se6 by a direct one-temperature method in evacuated quartz ampoules at temperatures above the melting point of the initial and final products. The initial compounds were synthesized by the reaction of their high purity component elements in stoichiometric proportion. According to the results of the research, it was found that cross-sections based on TlSbP2Se6 and the thermally stable compounds of the Tl2Se-Sb2Se3 section are quasibinary: Sb2Se3–TlSbP2Se6 and TlSbSe2–TlSbP2Se6. Tl9SbSe6 – TlSbP2Se6 and Tl2Se - TlSbP2Se6 systems are not quasibinary, instead quasibinary sections Tl2Se-Tl4P2Se6 and Tl9SbSe6-Tl4P2Se6 which crossing their. The phase equilibrium in Sb2Se3 – TlSbP2Se6 and TlSbSe2 – TlSbP2Se6 systems were studied by common differential thermal analysis (DTA), X-ray powder diffraction (XRD) and microstructure analysis. The eutectic interactions are observed in both systems. The invariant points coordinates are: 77 mol.% TlSbP2Se6, 709 K (system Sb2Se3 – TlSbP2Se6) and 45 mol.% TISbSe2, 680 K (system TlSbSe2 – TlSbP2Se6). Significant boundary solid solutions are formed on the basis of the quaternary compound. Their region extends up to 10 mol% in the system Sb2Se3 – TlSbP2Se6 and to about 18 mol.% in the system TlSbSe2 –TlSbP2Se6 at annealing temperature (573 К). Near the Sb2Se3 and TlSbSe2, the solubility limits do not exceed several mol.%.

scholarly journals Numerical simulation of all-normal dispersion visible to near-infrared supercontinuum generation in photonic crystal fibers with core filled chloroform

2021 ◽  
Vol 130 (1B) ◽  
pp. 43-51
Author(s):  
Thi Minh Ngoc Vo ◽  
Dinh Quang Ho ◽  
Tung Thanh Le ◽  
Thi Gai Le ◽  
Canh Trung Le ◽  
...  
Keyword(s):  
Photonic Crystal ◽  
Photonic Crystal Fiber ◽  
Near Infrared ◽  
Cost Effective ◽  
Fused Silica ◽  
Fiber Structure ◽  
Normal Dispersion ◽  
Crystal Fiber ◽  
Crystal Fibers ◽  
Mode Area

This study proposes a photonic crystal fiber made of fused silica glass, with the core infiltrated with chloroform as a new source of supercontinuum (SC) spectrum. We numerically study the guiding properties of the fiber structure in terms of characteristic dispersion and mode area of the fundamental mode. Based on the results, we optimized the structural geometries of the CHCl3-core photonic crystal fiber to support the broadband SC generations. The fiber structure with a lattice constant of 1 μm, a filling factor of 0.8, and the diameter of the first-ring air holes equaling 0.5 μm operates in all-normal dispersion. The SC with a broadened spectral bandwidth of 0.64 to 1.80 μm is formed by using a pump pulse with a wavelength of 850 nm, 120 fs duration, and power of 0.833 kW. That fiber would be a good candidate for all-fiber SC sources as cost-effective alternative to glass core fibers.

3D Plant Modelling Using Spectral Data from Visible to Near Infrared Range

2015 ◽  
pp. 273-294
Author(s):  
Ali Zia ◽  
Jie Liang
Keyword(s):  
Hyperspectral Imaging ◽  
Material Properties ◽  
Near Infrared ◽  
Infrared Range ◽  
Plant Surface ◽  
Imaging Device ◽  
Plant Phenomics ◽  
Physical Traits ◽  
Plant Modelling ◽  
Near Infrared Range

Plant phenomics research requires different types of sensors employed to measure the physical traits of plant surface and to estimate the biomass. Of particular interests is the hyperspectral imaging device which captures wavelength indexed band images that characterize material properties of objects under study. This chapter introduces a proof of concept research that builds 3D plant model directly from hyperspectral images captured in a controlled lab environment. The method presented in this chapter allows fine structural-spectral information of an object be captured and integrated into the 3D model, which can be used to support further research and applications. The hyperspectral imaging has shown clear advantages in segmenting plant from its background and is very promising in generating comprehensive 3D plant models.

Sign in / Sign up

Export Citation Format

Share Document