scholarly journals Technical Model of Micro Electrical Discharge Machining (EDM) Milling Suitable for Bottom Grooved Micromixer Design Optimization

Micromachines ◽  
2020 ◽  
Vol 11 (6) ◽  
pp. 594 ◽  
Author(s):  
Izidor Sabotin ◽  
Gianluca Tristo ◽  
Joško Valentinčič
Keyword(s):  
Design Optimization ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Electrode Wear ◽  
Micro Edm ◽  
Efficient Design ◽  
Machining Time ◽  
Micro Electrical Discharge Machining ◽  
Technical Model

In this paper, development of a technical model of micro Electrical Discharge Machining in milling configuration (EDM milling) is presented. The input to the model is a parametrically presented feature geometry and the output is a feature machining time. To model key factors influencing feature machining time, an experimental campaign by machining various microgrooves into corrosive resistant steel was executed. The following parameters were investigated: electrode dressing time, material removal rate, electrode wear, electrode wear control time and machining strategy. The technology data and knowledge base were constructed using data obtained experimentally. The model is applicable for groove-like features, commonly applied in bottom grooved micromixers (BGMs), with widths from 40 to 120 µm and depths up to 100 µm. The optimization of a BGM geometry is presented as a case study of the model usage. The mixing performances of various micromixer designs, compliant with micro EDM milling technology, were evaluated using computational fluid dynamics modelling. The results show that slanted groove micromixer is a favourable design to be implemented when micro EDM milling technology is applied. The presented technical model provides an efficient design optimization tool and, thus, aims to be used by a microfluidic design engineer.

Recent Patents on Micro-EDM Milling

2020 ◽  
Vol 13 (3) ◽  
pp. 219-229
Author(s):  
Baocheng Xie ◽  
Jianguo Liu ◽  
Yongqiu Chen
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Three Dimensional ◽  
Processing Method ◽  
Electrode Wear ◽  
Micro Edm ◽  
Processing Efficiency ◽  
Processing Methods ◽  
Machining Quality ◽  
Micro Electrical Discharge Machining

Background: Micro-Electrical Discharge Machining (EDM) milling is widely used in the processing of complex cavities and micro-three-dimensional structures, which is a more effective processing method for micro-precision parts. Thus, more attention has been paid on the micro-EDM milling. Objective : To meet the increasing requirement of machining quality and machining efficiency of micro- EDM milling, the processing devices and processing methods of micro-EDM milling are being improved continuously. Methods: This paper reviews various current representative patents related to the processing devices and processing methods of micro-EDM milling. Results: Through summarizing a large number of patents about processing devices and processing methods of micro-EDM milling, the main problems of current development, such as the strategy of electrode wear compensation and the development trends of processing devices and processing methods of micro-EDM milling are discussed. Conclusion: The optimization of processing devices and processing methods of micro-EDM milling are conducive to solving the problems of processing efficiency and quality. More relevant patents will be invented in the future.

Study on the Effect of Nano and Micro MoS2 Powder in Micro-Electrical Discharge Machining

2011 ◽  
Vol 264-265 ◽  
pp. 1450-1455 ◽  
Author(s):  
Gunawan Setia Prihandana ◽  
Tutik Sriani ◽  
Kei Prihandana ◽  
Yuta Prihandana ◽  
Muslim Mahardika ◽  
...  
Keyword(s):  
Surface Quality ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Micro Edm ◽  
Micro Electrical Discharge Machining ◽  
Powder Suspension ◽  
Size Powder

The application of powder mixed dielectric to improve the efficiency of electrical discharge machining (EDM) has been acknowledged extensively. However, the study of micro-size powder suspension in micro-EDM field is still limited. In this research, nano and micro size powder of MoS2 were used as catalyst agent. Powder suspension in different size was able to provide significant improvement in material removal rate and surface quality to increase the efficiency in μ- EDM processes.

A Simulation Study on Rod Electrode Wear in Micro-EDM

2012 ◽  
Vol 472-475 ◽  
pp. 2426-2429 ◽  
Author(s):  
Hu Wang ◽  
Yuan Gang Wang ◽  
Meng Hua Wu ◽  
Xiao Peng Li ◽  
Yu Liu
Keyword(s):  
Adverse Effect ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Electrical Discharge ◽  
Skin Effect ◽  
Electrical Discharge Machining ◽  
Electrode Wear ◽  
Micro Edm ◽  
Element Analysis ◽  
Micro Electrical Discharge Machining

Electrode wear has a great adverse effect on the accuracy of Micro Electrical Discharge Machining (Micro-EDM) and impedes the improvement of Micro-EDM. In this study the distribution of electric field and current density was analyzed exhaustively in order to explore the generating mechanisms of rod electrode wear by finite element analysis and experiment. Experimental results indicated that corner wear occurred first, followed by side wear resulted from skin effect and debris in Micro-EDM, which was significant in enhancing the accuracy of machining.

Experimental Analysis on Technology of Piezoelectric Self-Adaptive Micro-EDM

2010 ◽  
Vol 143-144 ◽  
pp. 1434-1438
Author(s):  
Xiu Zhuo Fu ◽  
Qin He Zhang ◽  
Guang Hua Bao ◽  
Yu Jie Zhu
Keyword(s):  
Surface Roughness ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
New Technology ◽  
Electrode Wear ◽  
Micro Edm ◽  
Working Process ◽  
Micro Electrical Discharge Machining ◽  
Working Principle ◽  
Self Adaptive

Micro electrical discharge machining (micro-EDM) has some shortcomings such as poor material removal rate (MRR) and high electrode wear ratio (EWR) etc, in order to overcome these demerits, a new piezoelectric self-adaptive micro-EDM, based on inverse piezoelectric effect, was developed in this paper. The structure and working principle of this new technology are different from traditional micro-EDM. Piezoelectric actuator used as the micro driven mechanism and it is simple. This new technology can realize self-elimination in the working process because of its special structure. Working principles and process of the new system were analyzed in this paper. The effect of parameters such as voltage, capacitance, and resistance on MRR, EWR and surface roughness was analyzed. Statistical analyses of the results show that voltage, capacitance significantly influence MRR, EWR and surface roughness. Resistance R1 and R2 has much influence on MRR and relative small effect on EWR and surface roughness.

Optimization of μEDM process assisted with rotating magnetic pulling force and ultrasonic vibration

2021 ◽  
pp. 095440892098440
Author(s):  
Gurpreet Singh ◽  
DR Prajapati ◽  
PS Satsangi
Keyword(s):  
Ultrasonic Vibration ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Machining Process ◽  
Micro Electrical Discharge Machining ◽  
Pulling Force ◽  
Tool Rotation

The micro-electrical discharge machining process is hindered by low material removal rate and low surface quality, which bound its capability. The assistance of ultrasonic vibration and magnetic pulling force in micro-electrical discharge machining helps to overcome this limitation and increase the stability of the machining process. In the present research, an attempt has been made on Taguchi based GRA optimization for µEDM assisted with ultrasonic vibration and magnetic pulling force while µEDM of SKD-5 die steel with the tubular copper electrode. The process parameters such as ultrasonic vibration, magnetic pulling force, tool rotation, energy and feed rate have been chosen as process variables. Material removal rate and taper of the feature have been selected as response measures. From the experimental study, it has been found that response output measures have been significantly improved by 18% as compared to non assisted µEDM. The best optimal combination of input parameters for improved performance measures were recorded as machining with ultrasonic vibration (U1), 0.25 kgf of magnetic pulling force (M1), 600 rpm of tool rotation (R2), 3.38 mJ of energy (E3) and 1.5 mm/min of Tool feed rate (F3). The confirmation trail was also carried out for the validation of the results attained by Grey Relational Analysis and confirmed that there is a substantial improvement with both assistance applied simultaneously.

Experimental Study of Machining of Shape Memory Alloys Using Dry Micro Electrical Discharge Machining Process

2018 ◽  
Author(s):  
Sagil James ◽  
Sharadkumar Kakadiya
Keyword(s):  
Shape Memory Alloys ◽  
Shape Memory ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Dielectric Medium ◽  
Machining Process ◽  
Machining Processes ◽  
Micro Electrical Discharge Machining

Shape Memory Alloys are smart materials that tend to remember and return to its original shape when subjected to deformation. These materials find numerous applications in robotics, automotive and biomedical industries. Micromachining of SMAs is often a considerable challenge using conventional machining processes. Micro-Electrical Discharge Machining is a combination of thermal and electrical processes, which can machine any electrically conductive material at micron scale independent of its hardness. It employs dielectric medium such as hydrocarbon oils, deionized water, and kerosene. Using liquid dielectrics has adverse effects on the machined surface causing cracking, white layer deposition, and irregular surface finish. These limitations can be minimized by using a dry dielectric medium such as air or nitrogen gas. This research involves the experimental study of micromachining of Shape Memory Alloys using dry Micro-Electrical Discharge Machining process. The study considers the effect of critical process parameters including discharge voltage and discharge current on the material removal rate and the tool wear rate. A comparison study is performed between the Micro-Electrical Discharge Machining process with using the liquid as well as air as the dielectric medium. In this study, microcavities are successfully machined on shape memory alloys using dry Micro-Electrical Discharge Machining process. The study found that the dry Micro-Electrical Discharge Machining produces a comparatively better surface finish, has lower tool wear and lesser material removal rate compared to the process using the liquid as the dielectric medium. The results of this research could extend the industrial applications of Micro Electrical Discharge Machining processes.

scholarly journals An Experimental Study on Processing TC4 with Nano Particle Surfactant Mixed Micro EDM

Materials ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6074
Author(s):  
Tingting Ni ◽  
Qingyu Liu ◽  
Zhiheng Chen ◽  
Dongsheng Jiang ◽  
Shufeng Sun
Keyword(s):  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Open Circuit ◽  
Deionized Water ◽  
Micro Edm ◽  
Nano Particle ◽  
Machining Performance ◽  
Machined Surface ◽  
Micro Electrical Discharge Machining ◽  
Lower Tool

Micro electrical discharge machining (micro EDM) is able to remove conductive material by non-contact instantaneous high temperature, which is more suitable for machining titanium and its alloys compared with traditional machining methods. To further improve the machining efficiency and machined surface quality of micro EDM, the nano particle surfactant mixed micro EDM method is put forward in this paper. Experiments were conducted to explore the effect of nano particle surfactant on the micro EDM performance of titanium alloy. The results show that the material removal rate of micro EDM in dielectric mixed with TiO2 is the highest when open-circuit voltage is 100 V, followed by Al2O3 and ZrO2. Lower tool wear rate can be produced by using dielectric mixed with nano particle surfactant. The taper ratio of micro EDM in dielectric mixed with nano particle surfactant is higher than that in deionized water. The surface roughness Ra of micro EDM in dielectric mixed with TiO2 can be 50% lower than that in deionized water. It is helpful to improve the machining performance by adding surface surfactant in the dielectric of micro EDM.

EXPERIMENTAL INVESTIGATION OF MICRO-EDM OPERATION IN INCONEL 718

2021 ◽  
pp. 2150102
Author(s):  
MAYANK CHOUBEY ◽  
K. P. MAITY
Keyword(s):  
Experimental Investigation ◽  
Inconel 718 ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Micro Edm ◽  
Machining Processes ◽  
Machining Time ◽  
Machine Material ◽  
Micro Holes ◽  
Unconventional Machining

The increasing trends towards miniaturized and lightweight components for various engineering and aerospace applications by unconventional machining the demand for micro-electrical discharge machining (EDM) have become increasingly wide. Micro-EDM is one of the most promising unconventional machining processes as compared to other unconventional machining due to its lower cost, ease of operation, and accuracy. This research explores the experimental investigation of micro-EDM operation on hard and difficult to machine material Inconel 718. The micro-holes were fabricated on an Inconel 718 workpiece with a copper electrode. The influence of input process parameters on material removal rate (MRR), machining time, and quality of the fabricated micro-holes were studied. Overcut and taperness of the fabricated micro-sized through holes were measured to address the accuracy of the fabricated micro-holes in micro-EDM operation. Experimental results reveal that the increase in current and voltage increases the MRR, and reduced machining time but at the cost of dimensional accuracy of the fabricated holes. The high value of current and voltage resulted in poor surface quality. The optimum machining condition that gives higher MRR with higher machining precision was obtained by experimenting while machining Inconel 718.

Sign in / Sign up

Export Citation Format

Share Document