scholarly journals Transparent Microelectrode Arrays Fabricated by Ion Beam Assisted Deposition for Neuronal Cell In Vitro Recordings

Micromachines ◽  
2020 ◽  
Vol 11 (5) ◽  
pp. 497 ◽  
Author(s):  
Tomi Ryynänen ◽  
Ropafadzo Mzezewa ◽  
Ella Meriläinen ◽  
Tanja Hyvärinen ◽  
Jukka Lekkala ◽  
...  
Keyword(s):  
Thin Films ◽  
Indium Tin Oxide ◽  
Microelectrode Array ◽  
Electrode Materials ◽  
Ion Beam ◽  
Neuronal Cell ◽  
Measurement Properties ◽  
Ito Thin Films ◽  
Sputter Deposited

Microelectrode array (MEA) is a tool used for recording bioelectric signals from electrically active cells in vitro. In this paper, ion beam assisted electron beam deposition (IBAD) has been used for depositing indium tin oxide (ITO) and titanium nitride (TiN) thin films which are applied as transparent track and electrode materials in MEAs. In the first version, both tracks and electrodes were made of ITO to guarantee full transparency and thus optimal imaging capability. In the second version, very thin (20 nm) ITO electrodes were coated with a thin (40 nm) TiN layer to decrease the impedance of Ø30 µm electrodes to one third (1200 kΩ → 320 kΩ) while maintaining (partial) transparency. The third version was also composed of transparent ITO tracks, but the measurement properties were optimized by using thick (200 nm) opaque TiN electrodes. In addition to the impedance, the optical transmission and electric noise levels of all three versions were characterized and the functionality of the MEAs was successfully demonstrated using human pluripotent stem cell-derived neuronal cells. To understand more thoroughly the factors contributing to the impedance, MEAs with higher IBAD ITO thickness as well as commercial sputter-deposited and highly conductive ITO were fabricated for comparison. Even if the sheet-resistance of our IBAD ITO thin films is very high compared to the sputtered one, the impedances of the MEAs of each ITO grade were found to be practically equal (e.g., 300–370 kΩ for Ø30 µm electrodes with 40 nm TiN coating). This implies that the increased resistance of the tracks, either caused by lower thickness or lower conductivity, has hardly any contribution to the impedance of the MEA electrodes. The impedance is almost completely defined by the double-layer interface between the electrode top layer and the medium including cells.

Room-temperature preparation of biaxially textured indium tin oxide thin films with ion-beam-assisted deposition

2003 ◽  
Vol 18 (2) ◽  
pp. 442-447 ◽  
Author(s):  
Karola Thiele ◽  
Sibylle Sievers ◽  
Christian Jooss ◽  
Jörg Hoffmann ◽  
Herbert C. Freyhardt
Keyword(s):  
Thin Films ◽  
Tin Oxide ◽  
Indium Tin Oxide ◽  
Room Temperature ◽  
Film Growth ◽  
Texture Evolution ◽  
Ion Beam ◽  
High Temperature Superconductors ◽  
Buffer Layers ◽  
Ito Thin Films

Biaxially aligned indium tin oxide (ITO) thin films were prepared by an ion-beamassisted deposition (IBAD) process at room temperature. Films with a transmittance at 550 nm of 90% and an electrical resistivity of 1.1 × 10−3 Ωcm for 300 and 250 nm thickness were obtained. Investigations of the texture evolution during IBAD film growth were carried out and compared to the well-established texture development in yttria-stabilized zirconia. An in-plane texture of 12.6° full width at half-maximum (FWHM) for a 1-μm-thick IBAD-ITO film was achieved. The quality of these films as electrically conductive buffer layers for YBa2Cu3O7-δ (YBCO) high-temperature superconductors was demonstrated by the subsequent deposition of high-currentcarrying YBCO films by thermal co-evaporation using a 3–5-nm-thick Y2O3 interlayer.A Jc of 0.76 MA/cm2 (77K, 0 T) was obtained for a 1 × 1 cm sample with ITO of 20° FWHM.

scholarly journals Nanostructural Characterisation and Optical Properties of Sputter-Deposited Thick Indium Tin Oxide (ITO) Coatings

Coatings ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1127
Author(s):  
Andrius Subacius ◽  
Bill Baloukas ◽  
Etienne Bousser ◽  
Steve J. Hinder ◽  
Mark A. Baker ◽  
...  
Keyword(s):  
Thin Films ◽  
Optical Properties ◽  
Tin Oxide ◽  
Indium Tin Oxide ◽  
Nanocrystalline Structure ◽  
Optical Transmittance ◽  
Glass Substrates ◽  
Ito Thin Films ◽  
Sputter Deposited ◽  
Thick Coatings

Indium tin oxide (ITO) thin films, used in many optoelectronic applications, are typically grown to a thickness of a maximum of a few hundred nanometres. In this work, the composition, microstructure and optical/electrical properties of thick ITO coatings deposited by radio frequency magnetron sputtering from a ceramic ITO target in an Ar/O2 gas mixture (total O2 flow of 1%) on unheated glass substrates are reported for the first time. In contrast to the commonly observed (200) or (400) preferential orientations in ITO thin films, the approximately 3.3 μm thick coatings display a (622) preferential orientation. The ITO coatings exhibit a purely nanocrystalline structure and show good electrical and optical properties, such as an electrical resistivity of 1.3 × 10−1 Ω·cm, optical transmittance at 550 nm of ~60% and optical band gap of 2.9 eV. The initial results presented here are expected to provide useful information for future studies on the synthesis of high-quality thick ITO coatings.

Effect of Emitting Current Ion Source on Structural, Optical and Electrical Properties of Nanostructured ITO Thin Films by Ion-Beam Assisted Evaporation

2014 ◽  
Vol 979 ◽  
pp. 263-266 ◽  
Author(s):  
Bhumin Yosvichit ◽  
Mati Horprathum ◽  
Pitak Eiamchai ◽  
Viyapol Patthanasetakul ◽  
Benjarong Samransuksamer ◽  
...  
Keyword(s):  
Thin Films ◽  
Electrical Properties ◽  
Carrier Concentration ◽  
Indium Tin Oxide ◽  
Ion Beam ◽  
Ion Source ◽  
Optical And Electrical Properties ◽  
Substrate Heating ◽  
Ito Thin Films ◽  
Ito Films

Transparent conductive oxides (TCOs) with indium tin oxide (ITO) thin films were deposited without substrate heating and post-deposition anneal using ion-beam assisted evaporation technique on glass and silicon substrates. The oxygen ion with emitting current produced using End-Hall ion source for bombardment of growing surface to improve ITO films structure. In this study, we investigate the effect of an ion flux to ITO films in terms of structural, optical and electrical properties. The emitting current can be varied from 0.5 to 2.0 A with the oxygen flow rate 7 sccm. The total film thickness and deposition rate are 200 nm and 0.2 nm/s, respectively. The structural properties of thin films were characterized by X-ray diffraction (XRD) to discover the preferred orientation with phase of crystalline and scanning electron microscopy (SEM) to examine the surface morphology in cross-section view. To determine the transmission spectra of the films, UV-visible spectrometer is introduced. Moreover, the films were also measured to investigate resistivity, carrier concentration, mobility and sheet resistance by Hall-effect measurements and four-point probe. It has been found that the ITO films with lowest electrical resistivity for the emitting current of 1 A about 5.57x10-4 Ω.cm and slightly increases with increase of the emitting current. The mobility and carrier concentration rapidly decreases with increase the emitting current from 1.0 A to 2.0 A.

scholarly journals Improving Performance of CIGS Solar Cells by Annealing ITO Thin Films Electrodes

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Chuan Lung Chuang ◽  
Ming Wei Chang ◽  
Nien Po Chen ◽  
Chung Chiang Pan ◽  
Chung Ping Liu
Keyword(s):  
Thin Films ◽  
Optical Properties ◽  
Solar Cells ◽  
Indium Tin Oxide ◽  
Copper Indium Gallium Diselenide ◽  
Glass Substrates ◽  
Ito Film ◽  
Ito Thin Films ◽  
Cigs Solar Cells ◽  
Ito Films

Indium tin oxide (ITO) thin films were grown on glass substrates by direct current (DC) reactive magnetron sputtering at room temperature. Annealing at the optimal temperature can considerably improve the composition, structure, optical properties, and electrical properties of the ITO film. An ITO sample with a favorable crystalline structure was obtained by annealing in fixed oxygen/argon ratio of 0.03 at 400°C for 30 min. The carrier concentration, mobility, resistivity, band gap, transmission in the visible-light region, and transmission in the near-IR regions of the ITO sample were-1.6E+20 cm−3,2.7E+01 cm2/Vs,1.4E-03 Ohm-cm, 3.2 eV, 89.1%, and 94.7%, respectively. Thus, annealing improved the average transmissions (400–1200 nm) of the ITO film by 16.36%. Moreover, annealing a copper-indium-gallium-diselenide (CIGS) solar cell at 400°C for 30 min in air improved its efficiency by 18.75%. The characteristics of annealing ITO films importantly affect the structural, morphological, electrical, and optical properties of ITO films that are used in solar cells.

Dependence of Ferroelectric Properties of SBT Based Capacitors on the Electrode Material

1998 ◽  
Vol 541 ◽  
Author(s):  
S. Tirumala ◽  
S. O. Ryu ◽  
K. B. Lee ◽  
R. Vedula ◽  
S. B. Desu
Keyword(s):  
Thin Films ◽  
Electrode Material ◽  
Electrode Materials ◽  
Perovskite Phase ◽  
Ferroelectric Properties ◽  
Si Substrates ◽  
Non Volatile Memory ◽  
Metal Organic ◽  
Sputter Deposited ◽  
Memory Applications

AbstractThe effect of various electrode materials on the ferroelectric properties of SrBi2Ta2O9 (SBT) thin films has been investigated for non-volatile memory applications. Two sets of electrode structures, viz., Pt-Ir based and Pt-Rh based, were sputter deposited in-situ on Si substrates. SBT thin films were deposited on these electrodes using a metal-organic solution deposition technique followed by a post-deposition anneal at 750 °C in oxygen. Structural characterization revealed a polycrystalline nature with predominant perovskite phase in SBT thin films. Ferroelectric properties were studied in capacitor mode by depositing top electrodes, where the top electrode material is identical to that of the bottom electrode. Extensive analysis of the ferroelectric properties signify the important role played by the electrode material in establishing the device applicability is reported in this work.

Characteristics of Ion Beam Assisted ITO Thin Films Deposited by RF Magnetron Sputtering

2014 ◽  
Vol 601 (1) ◽  
pp. 57-63 ◽  
Author(s):  
Kyong Chan Heo ◽  
Phil Kook Son ◽  
Youngku Sohn ◽  
Jonghoon Yi ◽  
Jin Hyuk Kwon ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Ion Beam ◽  
Rf Magnetron Sputtering ◽  
Ito Thin Films

ITO Thin Films on Silicon Buffer by Sol Gel Method

2006 ◽  
Vol 514-516 ◽  
pp. 1155-1160 ◽  
Author(s):  
Talaat Moussa Hammad
Keyword(s):  
Thin Films ◽  
Indium Tin Oxide ◽  
Optical Transmission ◽  
Sol Gel ◽  
Precursor Solution ◽  
Charge Carriers ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ito Thin Films ◽  
Uv Visible

Sol gel indium tin oxide thin films (In: Sn = 90:10) were prepared by the sol-gel dipcoating process on silicon buffer substrate. The precursor solution was prepared by mixing SnCl2.2H2O and InCl3 dissolved in ethanol and acetic acid. The crystalline structure and grain orientation of ITO films were determined by X-ray diffraction. The surface morphology of the films was characterized by scanning electron microscope (SEM). Optical transmission and reflectance spectra of the films were analyzed by using a UV-visible spectrophotometer. The transport properties of majority charge carriers for these films were studied by Hall measurement. ITO thin film with electrical resistivity of 7.6 ×10-3 3.cm, Hall mobility of approximately 2 cm2(Vs)-1 and free carrier concentration of approximately 4.2 ×1020 cm-3 are obtained for films 100 nm thick films. The I-V curve measurement showed typical I-V characteristic behavior of sol gel ITO thin films.

Magnetic characterization of ion-beam sputter deposited permalloy thin films

1992 ◽  
Vol 104-107 ◽  
pp. 1847-1850 ◽  
Author(s):  
Michael A. Russak ◽  
Christopher V. Jahnes ◽  
Erik Klokholm ◽  
Bojan Petek
Keyword(s):  
Thin Films ◽  
Ion Beam ◽  
Magnetic Characterization ◽  
Sputter Deposited ◽  
Permalloy Thin Films

scholarly journals Different electrode anodes used in OLED devices Diferentes eletrodos anodos usados em dispositivos OLEDs

2021 ◽  
Author(s):  
Emerson Roberto Santos ◽  
Thiago de Carvalho Fullenbach ◽  
Marina Sparvoli Medeiros ◽  
Luis da Silva Zambom ◽  
Roberto Koji Onmori ◽  
...  
Keyword(s):  
Thin Films ◽  
Tin Oxide ◽  
Threshold Voltage ◽  
Indium Tin Oxide ◽  
Light Emitting Diode ◽  
Electrical Current ◽  
High Threshold ◽  
Diamond Coatings ◽  
Ito Thin Films ◽  
Order Of Magnitude

Transparent conductive oxides (TCOs) known as indium tin oxide (ITO) and fluorine tin oxide (FTO) deposited on glass were compared by different techniques and also as anodes in organic light-emitting diode (OLED) devices with same structure. ITO produced at laboratory was compared with the commercial one manufactured by different companies: Diamond Coatings, Displaytech and Sigma-Aldrich, and FTO produced at laboratory was compared with the commercial one manufactured by Flexitec Company. FTO thin films produced at laboratory presented the lowest performance measured by Hall effect technique and also by I-V curve of OLED device with low electrical current and high threshold voltage. ITO thin films produced at laboratory presented elevated sheet resistance in comparison with commercial ITOs (approximately one order of magnitude greater), that can be related by a high number of defects as discontinuity of the chemical lattice or low crystalline structure. In the assembly of OLED devices with ITO and FTO produced at laboratory, neither presented luminances. ITO manufactured by Sigma-Aldrich company presented better electrical and optical characteristics, as low electrical resistivity, good wettability, favorable transmittance, perfect physicalchemical stability and lowest threshold voltage (from 3 to 4.5 V) for OLED devices.

Sign in / Sign up

Export Citation Format

Share Document