scholarly journals On the Impact of the Fabrication Method on the Performance of 3D Printed Mixers

Micromachines ◽  
2019 ◽  
Vol 10 (5) ◽  
pp. 298 ◽  
Author(s):  
Zeraatkar ◽  
Filippini ◽  
Percoco
Keyword(s):  
3D Printing ◽  
Lab On A Chip ◽  
Microfluidic Devices ◽  
Fused Deposition Modelling ◽  
Fabrication Method ◽  
Fused Deposition ◽  
3D Printed ◽  
The Impact

A wide variety of 3D printing technologies have been used for the fabrication of lab-on-a-chip (LOC) devices in recent years. Despite the large number of studies having examined the use of 3D printing technologies in microfluidic devices, the effect of the fabrication method on their performance has received little attention. In this paper, a comparison is shown between unibody-LOC micro-mixers, a particular type of monolithic design for 3D printed LOCs, fabricated in polyjet, stereolithography (SLA) and fused deposition modelling (FDM or FFF) platforms, paying particular attention to the inherent limitations of each fabrication platform and how these affect the performance of the manufactured devices.

scholarly journals Parameters Affecting the Mechanical Properties of Three-Dimensional (3D) Printed Carbon Fiber-Reinforced Polylactide Composites

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2456
Author(s):  
Demei Lee ◽  
Guan-Yu Wu
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
3D Printing ◽  
Three Dimensional ◽  
Fused Deposition Modelling ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Bed Temperature ◽  
3D Printed ◽  
The Impact

Three-dimensional (3D) printing is a manufacturing technology which creates three-dimensional objects layer-by-layer or drop-by-drop with minimal material waste. Despite the fact that 3D printing is a versatile and adaptable process and has advantages in establishing complex and net-shaped structures over conventional manufacturing methods, the challenge remains in identifying the optimal parameters for the 3D printing process. This study investigated the influence of processing parameters on the mechanical properties of Fused Deposition Modelling (FDM)-printed carbon fiber-filled polylactide (CFR-PLA) composites by employing an orthogonal array model. After printing, the tensile and impact strengths of the printed composites were measured, and the effects of different parameters on these strengths were examined. The experimental results indicate that 3D-printed CFR-PLA showed a rougher surface morphology than virgin PLA. For the variables selected in this analysis, bed temperature was identified as the most influential parameter on the tensile strength of CFR-PLA-printed parts, while bed temperature and print orientation were the key parameters affecting the impact strengths of printed composites. The 45° orientation printed parts also showed superior mechanical strengths than the 90° printed parts.

scholarly journals 3D Printing of Thermo-Sensitive Drugs

Pharmaceutics ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1524
Author(s):  
Sadikalmahdi Abdella ◽  
Souha H. Youssef ◽  
Franklin Afinjuomo ◽  
Yunmei Song ◽  
Paris Fouladian ◽  
...  
Keyword(s):  
3D Printing ◽  
Three Dimensional ◽  
Fused Deposition Modelling ◽  
Future Directions ◽  
Digital Light Processing ◽  
Fused Deposition ◽  
Printing Technique ◽  
3D Printed ◽  
Semi Solid ◽  
Selection Of

Three-dimensional (3D) printing is among the rapidly evolving technologies with applications in many sectors. The pharmaceutical industry is no exception, and the approval of the first 3D-printed tablet (Spiratam®) marked a revolution in the field. Several studies reported the fabrication of different dosage forms using a range of 3D printing techniques. Thermosensitive drugs compose a considerable segment of available medications in the market requiring strict temperature control during processing to ensure their efficacy and safety. Heating involved in some of the 3D printing technologies raises concerns regarding the feasibility of the techniques for printing thermolabile drugs. Studies reported that semi-solid extrusion (SSE) is the commonly used printing technique to fabricate thermosensitive drugs. Digital light processing (DLP), binder jetting (BJ), and stereolithography (SLA) can also be used for the fabrication of thermosensitive drugs as they do not involve heating elements. Nonetheless, degradation of some drugs by light source used in the techniques was reported. Interestingly, fused deposition modelling (FDM) coupled with filling techniques offered protection against thermal degradation. Concepts such as selection of low melting point polymers, adjustment of printing parameters, and coupling of more than one printing technique were exploited in printing thermosensitive drugs. This systematic review presents challenges, 3DP procedures, and future directions of 3D printing of thermo-sensitive formulations.

Use of polymer concrete for large-scale 3D printing

2021 ◽  
Vol 27 (3) ◽  
pp. 465-474
Author(s):  
Martin Krčma ◽  
David Škaroupka ◽  
Petr Vosynek ◽  
Tomáš Zikmund ◽  
Jozef Kaiser ◽  
...  
Keyword(s):  
3D Printing ◽  
Large Scale ◽  
Mechanical Performance ◽  
Construction Material ◽  
Polymer Concrete ◽  
Fused Deposition Modelling ◽  
Cast State ◽  
Content Type ◽  
Fused Deposition ◽  
3D Printed

Purpose This paper aims to focus on the evaluation of a polymer concrete as a three-dimensional (3D) printing material. An associated company has developed plastic concrete made from reused unrecyclable plastic waste. Its intended use is as a construction material. Design/methodology/approach The concrete mix, called PolyBet, composed of polypropylene and glass sand, is printed by the fused deposition modelling process. The process of material and parameter selection is described. The mechanical properties of the filled material were compared to its cast state. Samples were made from castings and two different orientations of 3D-printed parts. Three-point flex tests were carried out, and the area of the break was examined. Computed tomography of the samples was carried out. Findings The influence of the 3D printing process on the material was evaluated. The mechanical performance of the longitudinal samples was close to the cast state. There was a difference in the failure mode between the states, with cast parts exhibiting a tougher behaviour, with fractures propagating in a stair-like manner. The 3D-printed samples exhibited high degrees of porosity. Originality/value The results suggest that the novel material is a good fit for 3D printing, with little to no degradation caused by the process. Layer adhesion was shown to be excellent, with negligible effect on the finished part for the longitudinal orientation. That means, if large-scale testing of buildability is successful, the material is a good fit for additive manufacturing of building components and other large-scale structures.

Mechanical Properties of Diamond Schwarzites: From Atomistic Models to 3D-Printed Structures

MRS Advances ◽  
2020 ◽  
Vol 5 (33-34) ◽  
pp. 1775-1781 ◽  
Author(s):  
Levi C. Felix ◽  
Vladimir Gaál ◽  
Cristiano F. Woellner ◽  
Varlei Rodrigues ◽  
Douglas S. Galvao
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Uniaxial Compression ◽  
Chemical Vapour ◽  
Md Simulations ◽  
Atomic Model ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Structural Applications ◽  
3D Printed

ABSTRACTTriply Periodic Minimal Surfaces (TPMS) possess locally minimized surface area under the constraint of periodic boundary conditions. Different families of surfaces were obtained with different topologies satisfying such conditions. Examples of such families include Primitive (P), Gyroid (G) and Diamond (D) surfaces. From a purely mathematical subject, TPMS have been recently found in materials science as optimal geometries for structural applications. Proposed by Mackay and Terrones in 1991, schwarzites are 3D crystalline porous carbon nanocrystals exhibiting a TPMS-like surface topology. Although their complex topology poses serious limitations on their synthesis with conventional nanoscale fabrication methods, such as Chemical Vapour Deposition (CVD), schwarzites can be fabricated by Additive Manufacturing (AM) techniques, such as 3D Printing. In this work, we used an optimized atomic model of a schwarzite structure from the D family (D8bal) to generate a surface mesh that was subsequently used for 3D-printing through Fused Deposition Modelling (FDM). This D schwarzite was 3D-printed with thermoplastic PolyLactic Acid (PLA) polymer filaments. Mechanical properties under uniaxial compression were investigated for both the atomic model and the 3D-printed one. Fully atomistic Molecular Dynamics (MD) simulations were also carried out to investigate the uniaxial compression behavior of the D8bal atomic model. Mechanical testings were performed on the 3D-printed schwarzite where the deformation mechanisms were found to be similar to those observed in MD simulations. These results are suggestive of a scale-independent mechanical behavior that is dominated by structural topology.

scholarly journals 3D Printed Microfluidics

2020 ◽  
Vol 13 (1) ◽  
pp. 45-65 ◽  
Author(s):  
Anna V. Nielsen ◽  
Michael J. Beauchamp ◽  
Gregory P. Nordin ◽  
Adam T. Woolley
Keyword(s):  
3D Printing ◽  
Early Stage ◽  
Three Dimensional ◽  
Microfluidic Devices ◽  
Fabrication Method ◽  
Size Scale ◽  
Additional Work ◽  
Fluidic Devices ◽  
3D Printed ◽  
Microfabrication Techniques

Traditional microfabrication techniques suffer from several disadvantages, including the inability to create truly three-dimensional (3D) architectures, expensive and time-consuming processes when changing device designs, and difficulty in transitioning from prototyping fabrication to bulk manufacturing. 3D printing is an emerging technique that could overcome these disadvantages. While most 3D printed fluidic devices and features to date have been on the millifluidic size scale, some truly microfluidic devices have been shown. Currently, stereolithography is the most promising approach for routine creation of microfluidic structures, but several approaches under development also have potential. Microfluidic 3D printing is still in an early stage, similar to where polydimethylsiloxane was two decades ago. With additional work to advance printer hardware and software control, expand and improve resin and printing material selections, and realize additional applications for 3D printed devices, we foresee 3D printing becoming the dominant microfluidic fabrication method.

scholarly journals Ten guidelines for the design of non-assembly mechanisms: The case of 3D-printed prosthetic hands

2018 ◽  
Vol 232 (9) ◽  
pp. 962-971 ◽  
Author(s):  
Juan Sebastian Cuellar ◽  
Gerwin Smit ◽  
Amir A Zadpoor ◽  
Paul Breedveld
Keyword(s):  
Developing Countries ◽  
3D Printing ◽  
Fused Deposition Modelling ◽  
Prosthetic Hand ◽  
Prosthetic Devices ◽  
Hand Prosthesis ◽  
Fused Deposition ◽  
Prosthetic Hands ◽  
Design Considerations ◽  
3D Printed

In developing countries, prosthetic workshops are limited, difficult to reach, or even non-existent. Especially, fabrication of active, multi-articulated, and personalized hand prosthetic devices is often seen as a time-consuming and demanding process. An active prosthetic hand made through the fused deposition modelling technology and fully assembled right after the end of the 3D printing process will increase accessibility of prosthetic devices by reducing or bypassing the current manufacturing and post-processing steps. In this study, an approach for producing active hand prosthesis that could be fabricated fully assembled by fused deposition modelling technology is developed. By presenting a successful case of non-assembly 3D printing, this article defines a list of design considerations that should be followed in order to achieve fully functional non-assembly devices. Ten design considerations for additive manufacturing of non-assembly mechanisms have been proposed and a design case has been successfully addressed resulting in a fully functional prosthetic hand. The hand prosthesis can be 3D printed with an inexpensive fused deposition modelling machine and is capable of performing different types of grasping. The activation force required to start a pinch grasp, the energy required for closing, and the overall mass are significantly lower than body-powered commercial prosthetic hands. The results suggest that this non-assembly design may be a good alternative for amputees in developing countries.

scholarly journals Three-dimensional Printing Versus Conventional Machining in the Creation of a Meatal Urethral Dilator: a Cost and Mechanical Strength Analysis

2020 ◽  
Author(s):  
Michael Yue-Cheng Chen ◽  
Jacob Skewes ◽  
Ryan Daley ◽  
Maria Ann Woodruff ◽  
Nicholas John Rukin
Keyword(s):  
3D Printing ◽  
Three Dimensional ◽  
Patient Specific ◽  
Strength Analysis ◽  
Fused Deposition Modelling ◽  
3D Printer ◽  
Current Time ◽  
Fused Deposition ◽  
3D Printed ◽  
Conventional Machining

Abstract BackgroundThree-dimensional (3D) printing is a promising technology but the limitations are often poorly understood. We compare different 3D printingmethods with conventional machining techniques in manufacturing meatal urethral dilators which were recently removed from the Australian market. MethodsA prototype dilator was 3D printed vertically orientated on a low cost fused deposition modelling (FDM) 3D printer in polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS). It was also 3D printed horizontally orientated in ABS on a high-end FDM 3D printer with soluble support material, as well as on a SLS 3D printer in medical nylon. The dilator was also machined in stainless steel using a lathe. All dilators were tested mechanically in a custom rig by hanging calibrated weights from the handle until the dilator snapped. ResultsThe horizontally printed ABS dilator experienced failure at a greater load than the vertically printed PLA and ABS dilators respectively (503g vs 283g vs 163g, p < 0.001). The SLS nylon dilator and machined steel dilator did not fail. The steel dilator is most expensive with a quantity of five at 98 USD each, but this decreases to 30 USD each for a quantity of 1000. In contrast, the cost for the SLS dilator is 33 USD each for five and 27 USD each for 1000. ConclusionsAt the current time 3D printing is not a replacement for conventional manufacturing. 3D printing is best used for patient-specific parts, prototyping or manufacturing complex parts that have additional functionality that cannot otherwise beachieved.

scholarly journals Development of a 3-dimensional printed tube thoracostomy task trainer: An improved methodology

2021 ◽  
Vol 6 (1) ◽  
pp. 109-113
Author(s):  
Wen Hao Chen ◽  
Shairah Radzi ◽  
Li Qi Chiu ◽  
Wai Yee Yeong ◽  
Sreenivasulu Reddy Mogali
Keyword(s):  
3D Printing ◽  
Chest Tube ◽  
Fused Deposition Modelling ◽  
3 Dimensional ◽  
Fused Deposition ◽  
Simulation Based ◽  
3D Printed ◽  
Medical Educators ◽  
Based Instruction ◽  
Training Modalities

Introduction: Simulation-based training has become a popular tool for chest tube training, but existing training modalities face inherent limitations. Cadaveric and animal models are limited by access and cost, while commercial models are often too costly for widespread use. Hence, medical educators seek a new modality for simulation-based instruction. 3D printing has seen growing applications in medicine, owing to its advantages in recreating anatomical detail using readily available medical images. Methods: Anonymised computer tomography data of a patient’s thorax was processed using modelling software to create a printable model. Compared to a previous study, 3D printing was applied extensively to this task trainer. A mixture of fused deposition modelling and material jetting technology allowed us to introduce superior haptics while keeping costs low. Given material limitations, the chest wall thickness was reduced to preserve the ease of incision and dissection. Results: The complete thoracostomy task trainer costs approximately SGD$130 (or USD$97), which is significantly cheaper compared to the average commercial task trainer. It requires approximately 118 hours of print time. The complete task trainer simulates the consistencies of ribs, intercostal muscles and skin. Conclusion: By utilising multiple 3D printing technologies, this paper aims to outline an improved methodology to produce a 3D printed chest tube simulator. An accurate evaluation can only be carried out after we improve on the anatomical fidelity of this prototype. A 3D printed task trainer has great potential to provide sustainable simulation-based education in the future.

scholarly journals O22 3D printed polyethylene oxide oral doses with innovative ‘radiator-like’ design: impact of molecular weight on mechanical and rheological properties and drug release

2019 ◽  
Vol 104 (6) ◽  
pp. e10.1-e10 ◽  
Author(s):  
M Peak ◽  
K Baj ◽  
A Isreb ◽  
M Wojsz ◽  
I Mohammad ◽  
...  
Keyword(s):  
Molecular Weight ◽  
3D Printing ◽  
Drug Release ◽  
Rheological Properties ◽  
Oral Dosage ◽  
Parallel Plates ◽  
Fused Deposition ◽  
Plate Spacing ◽  
3D Printed ◽  
The Impact

BackgroundDespite regulatory advances, lack of age-appropriate formulations (AAFs) remains a challenge in paediatric practice. 3D-printing of oral dosage forms (ODFs) offers potential for AAFs for children. Optimising drug release from 3D-printed ODFs is an important technological step. Despite the abundant use of polyethylene oxides (PEOs) and their extensive use as an excipient, there have been no previous reports of applying this thermoplastic polymer species alone to fused deposition modelling (FDM) 3D printing. We assessed the impact of polymer molecular weight (MW) on the mechanical properties of the resultant filaments and their rheological properties. In the FDM 3D printing process, we also tested the effect of an innovative radiator-like design of the ODF on the acceleration of drug release patterns.MethodsBlends of PEO (MW: 100K, 200K, 300K, 600K or 900K) with PEG 6K (plasticiser) and a model drug (theophylline) were prepared by hot-melt extrusion. The resultant filaments were used as a feed for a FDM 3D printer to fabricate innovative designs of ODFs in a radiator-like geometry with inter-connected paralleled plates and inter-plate spacing of either 0.5mm, 1mm, 1.5mm or 2mm.ResultsVarying blends of PEO and PEG allowed formation of mechanically resistant filaments (maximum load at break of 357, 608, 649, 882, 781 N for filament produced with 100K, 200K, 300K, 600K or 900K, respectively). Filaments of PEO at a MW of 200K-600K were compatible with FDM 3D printing. Further increase in PEO MW resulted in elevated shear viscosity (>104 Pa.S) at the printing temperature and hindered material flow during FDM 3D printing. A minimum spacing (1 mm) between parallel plates of the radiator-like design was essential to boost drug release from the structure.ConclusionThese findings are essential in the development of next-generation personalised drug delivery doses using specialised polymer/polymer blends purposely optimised for FDM 3D printing.Disclosure(s)Nothing to disclose

Impact of 3D-printing structure on the tribological properties of polymers

2020 ◽  
Vol 72 (6) ◽  
pp. 811-818 ◽  
Author(s):  
Muammel M. Hanon ◽  
Róbert Marczis ◽  
László Zsidai
Keyword(s):  
3D Printing ◽  
Tribological Properties ◽  
Future Research ◽  
Fused Deposition Modelling ◽  
Wear Depth ◽  
Printing Process ◽  
Content Type ◽  
Fused Deposition ◽  
Polylactide Acid ◽  
The Impact

Purpose The purpose of this paper is to examine the impact of three-dimensional (3D)-printing process settings (particularly print orientation) on the tribological properties of different polymers. Design/methodology/approach In this study, fused deposition modelling 3D-printing technology was used for fabricating the specimens. To evaluate the influence of print orientation, the test pieces were manufactured horizontally (X) and vertically (Z). The tribological properties of various printed polymers, which are polylactide acid, high tensile/high temperature-polylactide acid and polyethylene terephthalate-glycol have been studied. The tribological tests have been carried out under reciprocating sliding and dry condition. Findings The results show that the presence of various orientations during the 3D-printing process makes a difference in the coefficient of friction and the wear depth values. Findings suggest that printing structure in the horizontal orientation (X) assists in reducing friction and wear. Originality/value To date, there has been very limited research on the tribology of objects produced by 3D printing. This work was made as an attempt to pave the way for future research on the science of tribology of 3D-printed polymers.

Sign in / Sign up

Export Citation Format

Share Document