scholarly journals Study on the Nucleation and Growth of Pearlite Colony and Impact Toughness of Eutectoid Steel

Metals ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 1133 ◽  
Author(s):  
Zhang ◽  
Zhao ◽  
Tan ◽  
Ji ◽  
Xiang
Keyword(s):  
Grain Size ◽  
Impact Toughness ◽  
Colony Size ◽  
Eutectoid Steel ◽  
Austenitizing Temperature ◽  
Austenite Grain Size ◽  
Austenite Grain ◽  
Nucleation Sites ◽  
Pearlite Colony ◽  
The Impact

The relationship between microstructure parameters and mechanical properties was studied in this paper. The steel was heat-treated at different austenitizing temperatures to acquire varying microstructure. The results showed that austenite grain size increases with austenitizing temperature, while the pearlite colony size was relatively constant. The strength followed a Hall–Petch relationship with the austenite grain size, but the austenite grain size has nothing to do with the impact toughness. The control unit for determining the impact toughness of pearlitic steel is the pearlite colony size using a comparison method. Further studies have found that, in the hypoeutectoid steel and hypereutectoid steel, the pearlite colony size changes with the austenitizing temperature. However, when the eutectoid steel with a carbon content of 0.81% undergoes the isothermal transformation, the number of grain boundary precipitates is very few. There are many nucleation sites at the grain boundary. The pearlite colonies randomly nucleate at the grain boundaries and grow into the interior of the grains. Simultaneously, new pearlite colonies nucleate by the side of the existing pearlite colony. The intragranular pearlite colonies are also randomly nucleated. These nucleation sites increase the chance of the growing pearlite colonies colliding with each other, eventually resulting in a constant pearlite colony size.

Microstructure and Mechanical Properties of 3-Wire Electroslag Welded (ESW) High-Speed Pearlitic Rail Steel Joint

2020 ◽  
Vol 837 ◽  
pp. 28-34
Author(s):  
Adnan Raza Khan ◽  
Sheng Fu Yu
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Colony Size ◽  
High Speed ◽  
Fusion Line ◽  
Austenite Grain Size ◽  
Austenite Grain ◽  
Microstructure And Mechanical Properties ◽  
Pearlite Colony

The present paper aims at utilizing the 3-wire electroslag welding (ESW) to join high-speed pearlitic rail steels where microstructure and mechanical properties were investigated. The welded joint has produced an improved fracture force of 1396KN. WM was consisted of ferrite and pearlite having hardness of 27HRC, tensile strength of 748MPa and toughness of 12J, successively. HAZ was composed of pro-eutectoid ferrite and pearlite, where austenite grain size and pearlite colony size were reduced by moving away from the fusion line. In HAZ, near to the fusion line, the austenite grain size was 143±19μm, pearlite colony size was 52±9μm and pearlite interlamellar spacing was 90±27nm, which has produced hardness of 43.5HRC, tensile strength of 1228MPa, and toughness of 8J, successively. The entire investigation concludes that 3-wire ESW is an optimum and viable method, which has provided fine pearlite microstructure along with improved hardness and tensile strength.

Effect of Austenite Grain Size on Hardenability and Impact Toughness of SCM435H

2016 ◽  
Vol 867 ◽  
pp. 50-54
Author(s):  
Ji Lin Chen ◽  
Shi Peng Ruan ◽  
Li Jun Wang ◽  
Jin Po Zhai ◽  
Chao Liu
Keyword(s):  
Grain Size ◽  
Impact Toughness ◽  
Phase Region ◽  
Material Strength ◽  
Two Phase ◽  
Quenching Temperature ◽  
Austenite Grain Size ◽  
Austenite Grain ◽  
Strength And Plasticity ◽  
The Impact

The effects of austenite grain size on hardenability and impact toughness were investigated. The results show that: Since the beginning of the two-phase region with quenching temperature, the austenite grain size from the initial 4+6 mixed crystal at 740°C, and gradually increased to 10 at 860°C; Austenite grain size and hardenability was directly proportional to the austenite grain size increased from 8μm to 36μm, the biggest change is the hardness 10HRC; Austenite grain size and impact toughness is linear, with the decrease of grain size, the impact energy increases linearly, and the austenite grain size and impact toughness curve fitting. Comprehensive analysis for ensuring the hardenability of cold heading steels should be considered optimal matching of material strength and plasticity.

Effect of Austenitizing Temperature on the Quenching Microstructure and Properties of 51CrV4

2019 ◽  
Vol 944 ◽  
pp. 357-363
Author(s):  
Xiao Dong Zhang ◽  
Dian Xiu Xia ◽  
Shou Ren Wang
Keyword(s):  
Grain Size ◽  
Austenitizing Temperature ◽  
Austenite Grain Size ◽  
Microstructure And Properties ◽  
Austenite Grain ◽  
Test Steel ◽  
Austenite Grains ◽  
Martensite Structure

The effect of austenitizing temperature on the quenching microstructure and properties of 51CrV4 steel was studied. The results show that with the increase of austenitizing temperature, the austenite grains grow gradually. After quenching, the hardness increased first and then decreased, and the strength increased first and then decreased after tempering at 460°C. When the austenitizing temperature was 880°C, the austenite grains were fine and uniform, about 16μm, the martensite structure was dense, the strength and hardness reached maximum. When the austenitizing temperature was 910°C, the decarburization phenomenon was obvious, and the strength, hardness and plasticity of the test steel decreased obviously. When the austenitizing temperature exceeded 910°C, the austenite grains grow sharply and some grains were abnormally coarse. The austenite grain size reached 20μm and the microstructure was coarser at austenitizing temperature of 950°C. Therefore, in order to ensure uniform grain size and no decarburization under the premise of complete austenitization, the best austenitizing temperature of 51CrV4 steel for good properties is 880°C.

scholarly journals Study of Static Recrystallization Kinetics and the Evolution of Austenite Grain Size by Dynamic Recrystallization Refinement of an Eutectoid Steel

Metals ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 1289
Author(s):  
Cesar Facusseh ◽  
Armando Salinas ◽  
Alfredo Flores ◽  
Gerardo Altamirano
Keyword(s):  
Grain Size ◽  
Dynamic Recrystallization ◽  
Static Recrystallization ◽  
Controlled Rolling ◽  
Strain Rates ◽  
Peak Strain ◽  
Compression Tests ◽  
Eutectoid Steel ◽  
Austenite Grain Size ◽  
Austenite Grain

Interrupted and continuous hot compression tests were performed for eutectoid steel over the temperature range of 850 to 1050 °C and while using strain rates of 0.001, 0.01, 0.1, and 1 s−1. The interrupted tests were carried out to characterize the kinetics of static recrystallization(SRX) and determinate the interpass time conditions that are required for initiation and propagation of dynamic recrystallization (DRX), while considering that the material does not contain microalloying elements additions for the recrystallization delay. Continuous testing was used to investigate the evolution of the austenite grain size that results from DRX. The results indicate that carbon content accelerates the SRX rate. This effect was observed when the retardation of recrystallization due to a decrease in deformation temperature from 1050 to 850 °C was only about one order of magnitude. The expected decelerate effect on the SRX rate when the initial grain size increases from 86 to 387 µm was not significant for this material. Although the strain parameter has a strong influence on SRX rate, in contrast to a lesser degree of strain rate, both of the effects are nearly independent of the chemical composition. The calculated maximum interpass times that are compatible with DRCR (Dynamic Recrystallization Controlled Rolling), for relatively low strain rates, suggest that the onset and maintaining of the DRX is possible. However, while using the empirical equations that were developed in the present work to estimate the maximum times for high strain rates, such as those observed in the wire and rod mills, indicate that the DRX start is feasible, but maintaining this mechanism for 5% softening in each pass after peak strain is not possible.

The Influence of Increased Cr Content and Austenite Grain Size on the Kinetics of Phase Transformations when Cooling Hypo-Eutectoid Steel

2006 ◽  
Vol 258-260 ◽  
pp. 421-426
Author(s):  
Ignacy Wierszyłłowski
Keyword(s):  
Activation Energy ◽  
Grain Size ◽  
Carbon Steel ◽  
Phase Transformations ◽  
Austenite Phase ◽  
Eutectoid Steel ◽  
Austenite Grain Size ◽  
Cr Content ◽  
Austenite Grain ◽  
Kinetics Of

The paper presents the influence of the grain size and a little higher Cr content on the kinetics of austenite phase transformations during continuous cooling of hypo-eutectoid steel. The kinetics of austenite phase transformations during continuous cooling were determined by means of analysis of the dilatometric curves and structure investigations. The influence of the austenite grain size and the higher Cr content was analysed in two hypoeutectoid steels containing about 0.4% C. One of them had, Cr content higher, by about 1%. In both steels, the austenite grain size was changing insignificantly up to the austenitising temperature of about 950fl. Above that temperature, the austenite grain size in carbon steel grew much quicker than that in the steel with Cr addition. The austenite grain in the Cr enriched steel was smaller than that in carbon steel and, in spite of that, the duration of cooled austenite transformations were several times longer. This means that the phase transformations are much more strongly influenced by the addition of chromium slowing down carbon diffusion in austenite, than by the austenite grain size. For each phase transformation in the examined steels, the activation energy of the transformation has been determined. The activation energy of all the phase transformations varied slightly with the increase of austenitising temperature. On the basis of the obtained results, curves of true isothermal transformations have been developed for the beginning of the phase transformations in both steels, related to infinitely quick cooling down to the transformation temperature.

scholarly journals Effects of Austenitizing Temperature on Tensile and Impact Properties of a Martensitic Stainless Steel Containing Metastable Retained Austenite

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 1000
Author(s):  
Biao Deng ◽  
Dapeng Yang ◽  
Guodong Wang ◽  
Ziyong Hou ◽  
Hongliang Yi
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Retained Austenite ◽  
Chromium Content ◽  
Total Elongation ◽  
X Ray Diffraction ◽  
Austenitizing Temperature ◽  
Austenite Grain Size ◽  
The Impact ◽  
M23c6 Carbides

Austenitizing temperature is one decisive factor for the mechanical properties of medium carbon martensitic stainless steels (MCMSSs). In the present work, the effects of austenitizing temperature (1000, 1020, 1040 and 1060 °C) on the microstructure and mechanical properties of MCMSSs containing metastable retained austenite (RA) were investigated by means of electron microscopy, X-ray diffraction (XRD), as well as tensile and impact toughness tests. Results suggest that the microstructure including an area fraction of undissolved M23C6, carbon and chromium content in matrix, prior austenite grain size (PAGS), fraction and composition of RA in studied MCMSSs varies with employed austenitizing temperature. By optimizing austenitizing temperature (1060 °C for 40 min) and tempering (250 °C for 30 min) heat treatments, the MCMSS demonstrates excellent mechanical properties with the ultimate tensile strength of 1740 ± 8 MPa, a yield strength of 1237 ± 19 MPa, total elongation (ductility) of 10.3 ± 0.7% and impact toughness of 94.6 ± 8.0 Jcm−2 at room temperature. The increased ductility of alloys is mainly attributed to the RA with a suitable stability via a transformation-induced plasticity (TRIP) effect, and a matrix containing reduced carbon and chromium content. However, the impact toughness of MCMSSs largely depends on M23C6 carbides.

Sign in / Sign up

Export Citation Format

Share Document