scholarly journals Experiment of Process Strategy of Selective Laser Melting Forming Metal Nonhorizontal Overhanging Structure

Metals ◽  
2019 ◽  
Vol 9 (4) ◽  
pp. 385 ◽  
Author(s):  
Wentian Shi ◽  
Peng Wang ◽  
Yude Liu ◽  
Guoliang Han
Keyword(s):  
Surface Roughness ◽  
Selective Laser Melting ◽  
Laser Power ◽  
316L Stainless Steel ◽  
Laser Melting ◽  
Scanning Strategy ◽  
Forming Quality ◽  
Forming Angle ◽  
Suspension Structure

To improve the precision of the nonhorizontal suspension structure and the forming quality of the overhanging surface by selective laser melting, the influence of laser power on the upper surface and the overhanging surface forming quality of 316L stainless steel at different forming angles was studied in the experiment. The influence of different scanning strategies, upper surface remelting optimization, and overhang boundary scanning optimization on the formation of overhanging structures was compared and analyzed. The forming effect of chromium–nickel alloy is better than 316L stainless steel below the limit forming angle in the overhanging structure. The better forming effect of chromium–nickel alloy can be obtained by narrowing the hatch space with the boundary optimization process. The experiment results show that the forming of the overhanging structure below the limit forming angle should adopt the chessboard scanning strategy. The smaller laser power remelting is beneficial to both the forming of the overhanging surface and the quality of upper surface forming. The minimum value of surface roughness using the 110 W power laser twice during surface remelting and boundary scanning 75° overhanging surface can reach 11.9 μm and 31.1μm, respectively. The forming accuracy error range above the limit forming angle is controlled within 0.4 mm, and the forming quality is better. A boundary count scanning strategy was applied to this study to obtain lower overhanging surface roughness values. This research proposes a process optimization and improvement method for the nonhorizontal suspension structure formed by selective laser melting, which provides the process support for practical application.

scholarly journals Collaborative Optimization on Density and Surface Roughness of 316L Stainless Steel in Selective Laser Melting

2020 ◽  
Author(s):  
Yong Deng ◽  
Zhongfa Mao ◽  
Nan Yang ◽  
Xiaodong Niu ◽  
Xiangdong Lu
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Relative Density ◽  
Selective Laser Melting ◽  
Laser Power ◽  
316L Stainless Steel ◽  
Scanning Speed ◽  
Processing Parameters ◽  
Collaborative Optimization ◽  
Laser Melting

Although the concept of additive manufacturing has been proposed for several decades, momentum of selective laser melting (SLM) is finally starting to build. In SLM, density and surface roughness, as the important quality indexes of SLMed parts, are dependent on the processing parameters. However, there are few studies on their collaborative optimization in SLM to obtain high relative density and low surface roughness simultaneously in the previous literature. In this work, the response surface method was adopted to study the influences of different processing parameters (laser power, scanning speed and hatch space) on density and surface roughness of 316L stainless steel parts fabricated by SLM. The statistical relationship model between processing parameters and manufacturing quality is established. A multi-objective collaborative optimization strategy considering both density and surface roughness is proposed. The experimental results show that the main effects of processing parameters on the density and surface roughness are similar. It is noted that the effects of the laser power and scanning speed on the above objective quality show highly significant, while hatch space behaves an insignificant impact. Based on the above optimization, 316L stainless steel parts with excellent surface roughness and relative density can be obtained by SLM with optimized processing parameters.

scholarly journals Investigation of Laser Polishing of Four Selective Laser Melting Alloy Samples

2020 ◽  
Vol 10 (3) ◽  
pp. 760
Author(s):  
Dongqi Zhang ◽  
Jie Yu ◽  
Hui Li ◽  
Xin Zhou ◽  
Changhui Song ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Selective Laser Melting ◽  
Laser Power ◽  
Layer By Layer ◽  
Metal Powders ◽  
Laser Melting ◽  
Laser Polishing

Selective laser melting (SLM) is a layer by layer process of melting and solidifying of metal powders. The surface quality of the previous layer directly affects the uniformity of the next layer. If the surface roughness value of the previous layer is large, there is the possibility of not being able to complete the layering process such that the entire process has to be abandoned. At least, it may result in long term durability problem and the inhomogeneity, may even make the processed structure not be able to be predicted. In the present study, the ability of a fiber laser to in-situ polish the rough surfaces of four typical additive-manufactured alloys, namely, Ti6Al4V, AlSi10Mg, 316L and IN718 was demonstrated. The results revealed that the surface roughness of the as-received alloys could be reduced to about 3 μm through the application of the laser-polishing process, and the initial surfaces had roughness values of 8.80–16.64 μm. Meanwhile, for a given energy density, a higher laser power produced a laser-polishing effect that was often more obvious, with the surface roughness decreasing with an increase in the laser power. Further, the polishing strategy will be optimized by simulation in our following study.

Effects of laser power on the microstructure and mechanical properties of 316L stainless steel prepared by selective laser melting

2017 ◽  
Vol 31 (16-19) ◽  
pp. 1744015 ◽  
Author(s):  
Zeng Zheng ◽  
Lianfeng Wang ◽  
Biao Yan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Stainless Steel ◽  
Selective Laser Melting ◽  
Laser Power ◽  
Laser Scanning ◽  
316L Stainless Steel ◽  
Laser Melting ◽  
Scanning Strategy ◽  
Microstructure And Mechanical Properties

Selective laser melting (SLM) was used to prepare 316L stainless steel parts and the effects of laser power on the microstructure and mechanical properties of the final products were studied. With increasing applied laser power, the defects of as-built parts were reduced greatly and the as-built parts presented a highest relative density of 99.1%. The tensile strength of samples was significantly improved from 321 ± 10 MPa to 722 ± 10 MPa. The microhardness was homogeneous; the residual stresses in the samples were tensile, which were higher in the section perpendicular to the laser scanning strategy. The probable reasons for this phenomenon were proposed.

Effect of defocusing distance on the forming quality of inner structure parts manufactured via selective laser melting

2021 ◽  
pp. 095440892110590
Author(s):  
Weipeng Duan ◽  
Meiping Wu ◽  
Jitai Han ◽  
Yiqing Ma ◽  
Peipei Lu ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Energy Density ◽  
Selective Laser Melting ◽  
Surface Pressure ◽  
Laser Energy ◽  
Dimensional Accuracy ◽  
Laser Energy Density ◽  
Laser Melting ◽  
Forming Quality

A systematical work was studied to illustrate the influence of defocusing distance on the forming quality of inner structure fabricated by selective laser melting for Ti-6Al-4V alloy. The relationship between defocusing distance and dimensional accuracy, surface roughness as well as flatness was investigated, finite element analysis (FEA) was used to show the temperature distribution. The results show that defocusing distance not only had an impact on laser energy density, but also showed a significant influence on the surface pressure of the metal powder. Smaller defocusing distance (0.0 mm) accompanied with higher molten pool maximum temperature (3262.96°C), powder melting and splashing at the same time. On the contrary, larger defocusing distance leading to unmelted powder and powder bonding, which influences the forming quality of samples. Dimensional accuracy was less affected in 0.0, 1.0, 2.0 mm defocusing distance (5%), but changed dramatically when it is 3.0 mm (22%). In the same condition, similar variation trend of surface roughness (Ra) and flatness was observed, and varying from 5.1 to 27.3 μm and 0.05 to 0.26 mm, respectively. Simultaneously, the bottom surface is less affected, while the other three sides have the opposite situation. Pores and unmelted powder can be seen on the surface, it is the comprehensive effect of laser energy density and surface pressure. It proves that it is feasible to manufacture inner structure by controlling this process parameter during SLM process, the influence mechanism of defocusing distance on forming quality was also illustrated in this work.

scholarly journals Collaborative Optimization of Density and Surface Roughness of 316L Stainless Steel in Selective Laser Melting

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1601 ◽  
Author(s):  
Yong Deng ◽  
Zhongfa Mao ◽  
Nan Yang ◽  
Xiaodong Niu ◽  
Xiangdong Lu
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Relative Density ◽  
Selective Laser Melting ◽  
Laser Power ◽  
316L Stainless Steel ◽  
Scanning Speed ◽  
Processing Parameters ◽  
Collaborative Optimization ◽  
Laser Melting

Although the concept of additive manufacturing has been proposed for several decades, momentum in the area of selective laser melting (SLM) is finally starting to build. In SLM, density and surface roughness, as the important quality indexes of SLMed parts, are dependent on the processing parameters. However, there are few studies on their collaborative optimization during SLM to obtain high relative density and low surface roughness simultaneously in the literature. In this work, the response surface method was adopted to study the influences of different processing parameters (laser power, scanning speed and hatch space) on density and surface roughness of 316L stainless steel parts fabricated by SLM. A statistical relationship model between processing parameters and manufacturing quality is established. A multi-objective collaborative optimization strategy considering both density and surface roughness is proposed. The experimental results show that the main effects of processing parameters on the density and surface roughness are similar. We observed that the laser power and scanning speed significantly affected the above objective quality, but the influence of the hatch spacing was comparatively low. Based on the above optimization, 316L stainless steel parts with excellent surface roughness and relative density can be obtained by SLM with optimized processing parameters.

scholarly journals Interferometry of Gas-Phase Flows during Selective Laser Melting

2019 ◽  
Vol 10 (1) ◽  
pp. 231 ◽  
Author(s):  
Pavel A. Podrabinnik ◽  
Alexander E. Shtanko ◽  
Roman S. Khmyrov ◽  
Andrey D. Korotkov ◽  
Andrey V. Gusarov
Keyword(s):  
Gas Phase ◽  
Selective Laser Melting ◽  
Laser Power ◽  
Metal Vapor ◽  
Gas Jet ◽  
Laser Melting ◽  
Pressure Fields ◽  
Ambient Gas ◽  
Processing Zone

Gas-phase flows occurring in a plume in a processing zone during selective laser melting (SLM) can significantly affect the quality of the process. To further enhance SLM performance, the characteristics of the flows should be considered. In this article, the vapor-gas jet emerging from the laser processing zone was studied. It was visualized by interferometry to evaluate flow velocity, geometry and changes in refractory index depending on laser power. The velocity and pressure fields of the vapor jet and the entrained ambient gas were estimated by mathematical modeling. It was shown that the increase of laser power led to higher jet velocity and greater change in its refractory index. The latter also was used to evaluate the content of metal vapor in the plume and its influence on the absorption of laser radiation.

scholarly journals The Influence of Process Parameters and Scanning Strategy on Lower Surface Quality of TA15 Parts Fabricated by Selective Laser Melting

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1228
Author(s):  
Junjie Jiang ◽  
Jianming Chen ◽  
Zhihao Ren ◽  
Zhongfa Mao ◽  
Xiangyu Ma ◽  
...  
Keyword(s):  
Surface Quality ◽  
Selective Laser Melting ◽  
Process Parameters ◽  
Flexible Manufacturing ◽  
Molten Pool ◽  
Lower Surface ◽  
Laser Melting ◽  
Scanning Strategy ◽  
Influence Of Process Parameters

With superior flexible manufacturing capability, selective laser melting (SLM) has attracted more and more attention in the aerospace, medical, and automotive industries. However, the poor quality of the lower surface in overhanging structures is still one of the factors that limits the wide application of SLM. In this work, the influence of process parameters and scanning strategy on the lower surface quality of SLMed TA15 (Ti-6Al-2Zr-1Mo-1V) titanium alloy parts were studied. The results showed that the laser surface energy density (EF) had a significant influence on the quality of the lower surface. Excessive EF led to obvious sinking of the molten pool and a serious slag hanging phenomenon. However, the too low EF easily contributed to the insufficient powder fusion in the lower surface area, which led to the agglomeration of a molten pool during core processing, resulting in slag hanging, pores, and powder spalling that reduced the quality of the lower surface. Moreover, the cross-remelting strategy and non-remelting strategy gained better surface quality at the low EF and high EF, respectively. In addition, it was found that the quality of the lower surface could be quickly and accurately evaluated by the cooling time of the molten pool during the processing of the lower surface. This research can increase the understanding of the forming mechanism of the lower surface and has certain guiding significance for the process optimization of the lower surface.

scholarly journals Selective laser melting of Ti6Al7Nb with hydroxyapatite addition

2014 ◽  
Vol 20 (4) ◽  
pp. 301-310 ◽  
Author(s):  
Teodora Marcu ◽  
Cinzia Menapace ◽  
Luca Girardini ◽  
Dan Leordean ◽  
Catalin Popa
Keyword(s):  
Selective Laser Melting ◽  
Laser Power ◽  
Design Methodology ◽  
Point Of View ◽  
Medical Applications ◽  
Laser Melting ◽  
Scanning Strategy ◽  
Content Type ◽  
Processing Times ◽  
Scanning Electron

Purpose – The purpose of this paper was to obtain by means of selective laser melting and then characterize biocomposites of medical-grade Ti6Al7Nb with hydroxyapatite (2 and 5 vol.%) and without hydroxyapatite, as reference. Design/methodology/approach – Rectangular samples were manufactured with the same scanning strategy; the laser power was between 50 W and 200 W. Processed samples were analysed by means of optical microscopy, scanning electron microscopy and microhardness. Findings – The results showed that despite the very short processing times, hydroxyapatite decomposed and interacted with the base Ti6Al7Nb material. The decomposition degree was found to depend on the applied laser power. From the porosity and bulk microstructure point of view, the most appropriate materials for the purposed medical applications were Ti6Al7Nb with hydroxyapatite processed with a laser power of 50 W. Originality/value – The originality of the present work consists in the study of the behaviour and interaction of hydroxyapatite additive with the Ti6Al7Nb base powder under selective laser melting conditions, as depending on the applied laser power.

Sign in / Sign up

Export Citation Format

Share Document